Moxa Technologies EtherDevice EDS-510A Series Manuel

Moxa EtherDevice™ Switch

EDS-510A Series Hardware Installation Guide

Sixth Edition, May 2010

Reproduction without permission is prohibited.

Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City, Taipei, Taiwan,

R.O.C.

TEL: +886-2-8919-1230

P/N: 1802005100013

- 2 -

Package Checklist

The EDS-510A is shipped with the following items. If any of these items are

missing or damaged, please contact your customer service representative for

assistance.

y1 EDS-510A EtherDevice Switch

yHardware Installation Guide (this guide)

yCD-ROM with user’s manual and Windows utility

yMoxa product warranty statement

yRJ45 to DB9 console port cable

yProtective caps for unused ports

yDIN-Rail mounting kit (attached to the EDS-510A’s rear panel by default)

Optional Accessories

ySFP-1GSXLC: Small Form factor Pluggable transceiver with 1000BaseSX,

LC, 0.5km, 0 to 60°C

ySFP-1GSXLC-T: Small Form factor Pluggable transceiver with

1000BaseSX, LC, 0.5km, 20 to 75°C

ySFP-1GLXLC: Small Form factor Pluggable transceiver with 1000BaseLX,

LC, 10km, 0 to 60°C

ySFP-1GLXLC-T: Small Form factor Pluggable transceiver with

1000BaseLX, LC, 10km, -40 to 75°C

ySFP-1GLHXLC: Small Form factor Pluggable transceiver with

1000BaseLHX, LC, 40 km, 0 to 60°C

ySFP-1GLHXLC-T: Small Form factor Pluggable transceiver with

1000BaseLHX, LC, 40 km, -40 to 75°C

ySFP-1GZXLC: Small Form factor Pluggable transceiver with 1000BaseZX,

80 km, LC, 0 to 60°C

yABC-01: Automatic Backup Configurator via RS-232 Console Port, 0 to

60°C

yDR-4524—DIN-Rail Power Supply (24 VDC, 45W/2A, with 85 to 264

VAC input)

yDR-75-24—DIN-Rail Power Supply (24 VDC, 75W/3.2A, with 85 to 264

VAC input)

yDR-120-24—DIN-Rail Power Supply (24 VDC, 120W/5A, with 88 to 132

VAC/176 to 264 VAC input by switch)

yEDS-SNMP OPC Server Pro—CD with EDS-SNMP OPC Server

software and user’s manual

yWK-46—Wall Mounting Kit (will be shipped with the product)

yRK-4U—4U-high 19" rack mounting kit

- 3 -

Panel Views of EDS-510A

EDS-510A-1GT2SFP

Front Panel View

EDS-510A-3GT

Front Panel View

EDS-510A-3SFP

Front Panel View

MSTR/HEAD

CPLR/TAILD

MSTR/HEAD

CPLR/TAILD

MSTR/HEAD

CPLR/TAILD

1. 1 to 7: 10/100BaseT(X) port

2. G1:

EDS-510A-3GT

10/100/1000BaseT(X) port

EDS-510A-1GT2SFP

10/100/1000BaseT(X) port

EDS-510A-3SFP

1000BaseSX/LX/LHX/ZX port

3. G2:

EDS-510A-3GT

10/100/1000BaseT(X) port

EDS-510A-1GT2SFP

1000BaseSX/LX/LHX/ZX port

EDS-510A-3SFP

1000BaseSX/LX/LHX/ZX port

4. G3:

EDS-510A-3GT

10/100/1000BaseT(X) port

EDS-510A-1GT2SFP

1000BaseSX/LX/LHX/ZX port

EDS-510A-3SFP

1000BaseSX/LX/LHX/ZX port

5. G1, G2, G3: LED indicators for

1000 Mbps ports

6. PWR1: LED for power input 1

7. PWR2: LED for power input 2

8. FAULT: LED indicator

9. MSTR/HEAD: LED indicator

10. CPLR/TAIL: LED indicator

11. Turbo Chain logo

12. 100M: LED indicator for TP port

13. 10M: LED indicator for TP port

14. Model Name

- 4 -

RS-232 CONSOLE

------

OFF

MASTER

COUPLER

TURBO

RING

PWR2

RELAY2

RELAY1

DI2

DI1

V2-

V2+

V1-

V1+

Top Panel View

Rear Panel View

4PWR1

Top Panel:

1. Ground screw

2. RS-232 console port

3. Heat dissipation orifices

4. DIP switches for Ring Master,

Ring Coupler, and Turbo Ring

5. 6-pin terminal block for DI 1, DI 2,

and PWR 2

6. 6-pin terminal block for PWR1,

Relay 1, and Relay 2

Rear Panel:

7. Screw holes for Wall Mounting Kit

8. DIN-Rail Kit

Mounting Dimensions (unit = mm)

Rear View

Side View Front View

DlN-Rail Kit

DlN-Rail

105.00

9.00

00.53

00.531

3.42

73.9377.6465.42

00.531

Wall Mounting Kit

7.75 30.50 7.75

3.5

08.66 50.75

13.9 18.2 13.9

30.00 15.0

51.3 13.9

80.2

DlN-Rail Kit

7.5 55 7.5

02.72 03.84

- 5 -

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the back

panel of the EDS-510A when you take it out of the box. If you need to

reattach the DIN-Rail attachment plate to the EDS-510A, make sure the stiff

metal spring is situated towards the top, as shown by the following figures.

STEP 1—Insert the top of the

DIN-Rail into the slot just below the

stiff metal spring.

STEP 2—The DIN-Rail attachment

unit will snap into place as shown in

the following illustration.

metal

spring

DIN-Rail

metal

spring

DIN-Rail

To remove the EDS-510A from the DIN-Rail, simply reverse Steps 1 and 2

above.

Wall Mounting (Optional)

For some applications, you will find it convenient to mount Moxa EDS-510A

on the wall, as shown in the following illustrations:

STEP 1—Remove the

aluminum DIN-Rail

attachment plate from the rear

panel of the EDS-510A, and

then attach the wall mount

plates with M3 screws, as

shown in the figure at the

right.

STEP 2—Mounting the EDS-510A on the wall requires 4

screws. Use the EDS-510A, with wall mount plates attached, as a

guide to mark the correct locations of the 4 screws. The heads of

the screws should be less than 6.0 mm in diameter, and the shafts

should be less than 3.5 mm in diameter, as shown in the figure on

at right.

6.0 mm

3.5 mm

NOTE Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw through

one of the keyhole-shaped apertures of the Wall Mounting Plates.

- 6 -

Do not screw the screws in all the

way—leave about 2 mm to allow room

for sliding the wall mount panel between

the wall and the screws.

STEP 3—Once the screws are fixed to

the wall, insert the four screw heads

through the wide parts of the

keyhole-shaped apertures, and then slide

the EDS-510A downwards, as indicated

in the figure at the right. Tighten the four

screws for more stability.

II 3G

ATEX Information

1. Certificate number DEMKO 08 ATEX 0810937x

2. Ambient range (-40°C ≤Tamb ≤75°C)

3. Certification string (Ex nC nL IIC T4)

4. Standards covered ( EN60079-0:2006,

EN60079-15:2005)

5. The conditions of safe usage:

yThese products must be mounted in an IP54 enclosure.

yInstall in an area of pollution degree 2 or less.

yUse a conductor wire of size 0.2 mm² or greater.

yPROVISIONS SHALL BE MADE, EITHER IN EXTERNAL TO

THE APPARATUS, TO PREVENT THE RATED VOLTAGE BEING

EXCEEDED BY THE TRANSIENTS DISTURBANCES OF MORE

THAN 40 %

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been

switched off or the area is known to be non-hazardous. The

devices may only be connected to the supply voltage shown on

the type plate. The devices are designed for operation with a

Safety Extra-Low Voltage. Thus, they may only be connected to

the supply voltage connections and to the signal contact with the

Safety Extra-Low Voltages (SELV) in compliance with IEC950/

EN60950/ VDE0805.

ATTENTION

This unit is a built-in type. When the unit is installed in another

piece of equipment, the equipment enclosing the unit must

comply with fire enclosure regulation IEC 60950/EN60950 (or

similar regulation).

- 7 -

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa EtherDevice Switch.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

Please read and follow these guidelines:

yUse separate paths to route wiring for power and devices. If power wiring

and device wiring paths must cross, make sure the wires are perpendicular

at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately

yYou can use the type of signal transmitted through a wire to determine

which wires should be kept separate. The rule of thumb is that wiring that

shares similar electrical characteristics can be bundled together

yYou should separate input wiring from output wiring

yWe advise that you label the wiring to all devices in the system.

Grounding the Moxa EDS-510A

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well-grounded

mounting surface such as a metal panel.

Wiring the Relay Contact

The EDS-510A has two sets of relay outputs—relay 1 and relay 2. Each relay

contact uses two contacts of the terminal block on the EDS-510A’s top panel.

Refer to the next section for detailed instructions on how to connect the wires

to the terminal block connector, and how to attach the terminal block

connector to the terminal block receptor.In this section, we illustrate the

meaning of the two contacts used to connect the relay contact.

RELAY1

RELAY2

FAULT:

The two sets of relay contacts of the

6-pin terminal block connector are

used to detect user-configured events.

The two wires attached to the fault

contacts form an open circuit when a

user-configured event is triggered. If a

user-configured event does not occur,

the fault circuit remains closed.

- 8 -

Wiring the Redundant Power Inputs

The EDS-510A has two sets of power inputs—power input 1 and power input

2. The top two contacts and the bottom two contacts of the 6-pin terminal

block connector on the EDS-510A’s top panel are used for the two digital

inputs. The top and front views of one of the terminal block connectors are

shown here.

PWR1

PWR2

V1- V1+

PWR1

V2- V2+

PWR2

V1- V1+V2- V2+

STEP 1: Insert the negative/positive

DC wires into the V-/V+ terminals,

respectively.

STEP 2: To keep the DC wires from

pulling loose, use a small flat-blade

screwdriver to tighten the wire-clamp

screws on the front of the terminal

block connector.

STEP 3: Insert the plastic terminal

block connector prongs into the

terminal block receptor, which is

located on the EDS-510A’s top panel.

Wiring the Digital Inputs

The EDS-510A has two sets of digital inputs, DI 1 and DI 2. Each DI consists

of two contacts of the 6-pin terminal block connector on the EDS-510A’s top

panel, which are used for the two DC inputs. The top and front views of one

of the terminal block connectors are shown here.

D2I

D1I

I1I2

D2ID1I

STEP 1: Insert the negative

(ground)/positive DI wires into the ┴/I1

terminals, respectively.

STEP 2: To keep the DI wires from

pulling loose, use a small flat-blade

screwdriver to tighten the wire-clamp

screws on the front of the terminal block

connector.

STEP 3: Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is located on the

EDS-510A’s top panel.

Communication Connections

Each EDS-510A switch has 3 types of communication port:

y1 RJ45 console port (RS-232 interface)

y7 10/100BaseTX Ethernet ports

y3 gigabit Ethernet ports:

3 10/100/1000BaseTX ports, or 1 10/100/1000BaseTX and 2

1000BaseSFP (mini-GBIC) ports, or 3 1000BaseSFP (mini-GBIC) ports

- 9 -

In this section, we present two types of diagrams—Pinout Diagrams and Cable

Wiring Diagrams—that convey information about the ports and the cables used

to connect the EDS-510A to other devices:

Pinouts—The “Pinouts” diagrams display the type of signal passing through

each of the port’s pins.

Cable Wiring—The “Cable Wiring” diagrams present standard cable wiring

schemes for cables used to connect the EDS-510A’s ports to other devices.

These diagrams display three pieces of information:

1. When building your own cable, refer to the “pin-to-pin” cable wiring

information displayed between the two vertical dashed lines to see

which pin of the connector on the left should be connected to which pin

of the connector on the right.

2. The information to the left of the left vertical dashed lines gives the

pinouts of the relevant EDS-510A port.

3. The information to the right of the right vertical dashed line gives the

pinouts of the opposing device’s port.

NOTE 1. The pin numbers for male DB9 connectors and hole numbers

for female DB9 connectors are labeled on the connector.

2. The pin numbers for 10-pin RJ45 connectors (and ports) are

typically not labeled on the connector (or port). Refer to the

following Pinout and Cable Wiring diagrams to see how

10-pin RJ45 pins are numbered

RS-232 Connection

The EDS-510A has one RS-232 (10-pin RJ45) console port, located on the

top panel. Use either an RJ45-to-DB9 (see the cable following wiring

diagrams) to connect the EDS-510A’s console port to your PC’s COM port.

You may then use a console terminal program, such as Moxa PComm

Terminal Emulator, to access the EDS-510A’s console configuration utility.

RJ45 (10-pin) Console Port Pinouts

Pin Description

1 ------

2 DSR

3 ------

4 GND

5 TxD

6 RxD

7 GND

8 ------

9 DTR

10 ------

110

- 10 -

RJ45 (10-pin) to DB9 (F) Cable Wiring

RJ45 Plug Pin 1

Moxa

EtherDevice

Server

RJ45

Connector

DCD

DSR

RTS

GND

TxD

RxD

CTS

DTR

COM Port

Female DB9

Connector

DCD

DTR

CTS

GND

RxD

TxD

RTS

DSR

Cable Wiring

4/7

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the EDS-510A’s front panel are used to

connect to Ethernet-enabled devices. Most users configure these ports for

Auto MDI/MDI-X mode, in which case the port’s pinouts are adjusted

automatically depending on the type of Ethernet cable used (straight-through

or cross-over), and the type of device (NIC-type or HUB/Switch-type)

connected to the port.

In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports. We also give cable wiring diagrams for

straight-through and cross-over Ethernet cables.

RJ45 (8-pin, MDI) Port Pinouts

Pin Signal

1 Tx+

2 Tx-

3 Rx+

6 Rx-

RJ45 (8-pin, MDI-X) Port Pinouts

Pin Signal

1 Rx+

2 Rx-

3 Tx+

6 Tx-

RJ45 (8-pin) to RJ45 (8-pin) Straight-through Cable Wiring

Straight-Through Cable

RJ45 Plug Pin 1

Switch Port

RJ45

Connector RJ45

Connecto

Tx+

Tx-

Rx+

Rx-

NIC Port

Cable Wiring

3 3

6 6

1 1

2 2

Rx+

Rx-

Tx+

Tx-

RJ45 (8-pin) to RJ45 (8-pin) Cross-over Cable Wiring

Cross-Over Cable

RJ45 Plug Pin 1

Switch Port

(NIC Port)

RJ45

Connector RJ45

Connector

Tx+

Tx-

Rx+

Rx-

(Rx+)

(Rx-)

(Tx+)

(Tx-)

(Tx+)

(Tx-)

(Rx+)

(Rx-)

Switch Port

(NIC Port)

Cable Wiring

3 1

6 2

1 3

2 6

Rx+

Rx-

Tx+

Tx-

Autres manuels pour EtherDevice EDS-510A Series

Table des matières

Autres manuels Moxa Technologies Changer

Moxa Technologies

Moxa Technologies EtherDevice EDS-P206A-4PoE Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-316 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies PT-7828 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-516A-T Manuel

Moxa Technologies

Moxa Technologies EDS-2008-EL Series Manuel utilisateur

Moxa Technologies

Moxa Technologies IEX-408E-2VDSL2-HV Manuel utilisateur

Moxa Technologies

Moxa Technologies IKS-6728 Series Manuel

Moxa Technologies

Moxa Technologies PT-7710 Series Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510 Series Manuel

Moxa Technologies

Moxa Technologies EDS-405A Manuel utilisateur

Moxa Technologies

Moxa Technologies PT-G7728 Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-30 Manuel

Moxa Technologies

Moxa Technologies PowerTrans PT-508-MM-ST-48 Manuel utilisateur

Moxa Technologies

Moxa Technologies PowerTrans PT-7728-PTP Manuel

Moxa Technologies

Moxa Technologies SPL-24 Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A Series Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A-3GT Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-728 Series Manuel

Moxa Technologies

Moxa Technologies EDS-726 Series Manuel

Moxa Technologies

Moxa Technologies EDS-600 Series Manuel

Moxa Technologies

Moxa Technologies PT-7528 Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-508 Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur