Moxa Technologies EtherDevice EDS-P510 Series Manuel utilisateur

P/N: 1802005101013

*1802005101013*

EDS-P510 Series

Quick Installation Guide

Moxa EtherDevice™ Switch

Edition 4.0, July 2017

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The Moxa EtherDevice™ EDS-P510 Series Ethernet switches are

Gigabit managed redundant Ethernet switches that come standard with 4

10/100BaseT(X) 802.3af (PoE) compliant Ethernet ports and 3 combo

Gigabit Ethernet ports. The EDS-P510 Ethernet switches provide up to

15.4 watts of power per PoE port, and allow power to be supplied to

connected devices (such as surveillance cameras, wireless access points,

and IP phones) when AC power is not readily available or cost-prohibitive

to provide locally. The EDS-P510 Ethernet switches are highly versatile,

and their SFP fiber port can transmit data up to 80 km from the device to

the control center with high EMI immunity. The Ethernet switches support

a variety of management functions, including Turbo Chain, IEEE 1588 PTP,

Turbo Ring, RSTP/STP, IGMP, VLAN, QoS, RMON, bandwidth

management, and port mirroring. The EDS-P510 series is designed

especially for security automation applications such as IP surveillance and

gate of entry systems, which can benefit from a scalable backbone

construction and Power-over-Ethernet support.

Package Checklist

The EDS-P510 is shipped with the following items. If any of these items

are missing or damaged, please contact your customer service

representative for assistance.

•1 EDS-P510 EtherDevice Switch

•RJ45 to DB9 console port cable

•Protective caps for unused ports

•DIN-Rail mounting kit (attached to the EDS-P510’s rear panel by

default)

•CD-ROM with user’s manual and Windows utility

•Quick installation guide (printed)

•Warranty card

- 3 -

Panel Views of EDS-P510

Front Panel:

1. 1 to 7: 10/100BaseT(X) port

2. G1 to G3: Combo

(10/100/1000BaseT(X) or

100/1000BaseSFP slot Gigabit

port.)

3. PWR1: LED for power input 1

4. PWR2: LED for power input 2

5. Fault LED

6. MSTR/HEAD LED

7. CPLR/TAIL LED

8. G1, G2, G3 LED for

10/100/1000Mbps speed

9. Port 1 to Port 7 LED for

10/100Mbps speed

10.

PoE port LED (Port 1 to Port 4)

11.

Model name

Top Panel

1. Ground screw

2. RS-232 console port

3. Heat dissipation orifices

4. DIP switches for Ring Master,

Ring Coupler, and Turbo Ring

5. 6-pin terminal block for DI 1,

DI 2, and PWR 2

6. 6-pin terminal block

for PWR1,

Relay 1 and Relay 2

Rear Panel:

Screw holes for Wall Mounting

Kit

8. DIN-Rail Kit

- 4 -

Mounting Dimensions

Unit = mm (inch)

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the

back panel of the EDS-P510 when you take it out of the box. If you need

to reattach the DIN-Rail attachment plate to the EDS-P510, make sure

the stiff metal spring is situated towards the top, as shown by the

following figures.

STEP 1

—Insert the top of the

DIN

-Rail into the slot just below

the stiff metal spring.

STEP 2

—The DIN-Rail attachment

unit will snap into place as shown in

the following illustration.

To remove the EDS-P510 from the DIN-Rail, simply reverse Steps 1 and

2 above.

- 5 -

Wall Mounting (Optional)

For some applications, you will find it convenient to mount Moxa

EDS-P510 on the wall, as shown in the following illustrations:

STEP 1

—

Remove the

aluminum DIN

-Rail

attachment plate from the

rear panel of the EDS

P510,

and then attach the wall

mount plates with M3

screws, as shown

in the

figure at the right.

STEP 2—Mounting the EDS-P510 on the wall requires 4

screws. Use the EDS

-P510, with wall mount plates

attached, as a guide to mark the correct locations of the

4 screws. The heads of the screws should be less than 6.0

mm in diameter, and the shafts should be less than 3.5

mm in diameter, as shown in the figure on at right.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw through

one of the keyhole-shaped apertures of the Wall Mounting Plates.

Do not screw the screws in all the way—leave about 2 mm to allow room

for sliding the wall mount panel between the wall and the screws.

STEP 3—Once the screws are

fixed to the wall, insert the four

screw heads through the wide

parts of the keyhole

-shaped

apertures, and then slide the

EDS

-P510 downwards, as

indicated in the figure at the right.

Tighten the four screws for more

stability.

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been

switched off or the area is known to be non

-hazardous. The

devices may only be connected to the supply voltage shown on

the type plate. The devices are designed for operation with a

afety Extra-Low V

oltage. Thus, they may only be connected to

the supply voltage connections and to the signal contact with the

afety Extra-Low Voltages (SELV) in compliance with

IEC60950-1/EN60950-1.

- 6 -

ATTENTION

This unit is a built

-in type. When the unit is installed in another

piece of equipment, the equipment enclosing the unit must

comply with fire enclosure regulation

IEC60950-1/EN60950-1

(or

similar regulation).

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa EtherDevice Switch.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable

for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

Please read and follow these guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together.

•You should separate input wiring from output wiring.

•We advise that you label the wiring to all devices in the system.

Grounding the Moxa EDS-P510

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to

a well-grounded

mounting surface such as a metal panel.

- 7 -

Wiring the Relay Contact

The EDS-P510 has two sets of relay outputs—relay 1 and relay 2. Each

relay contact uses two contacts of the terminal block on the EDS-P510’s

top panel. Refer to the next section for detailed instructions on how to

connect the wires to the terminal block connector, and how to attach the

terminal block connector to the terminal block receptor.

In this section, we illustrate the meaning of the two contacts used to

connect the relay contact.

FAULT:

The two sets of relay contacts of

the 6

pin terminal block connector

are used to detect user

configured

events. The two wires attached to

the

fault contacts form an open

circuit when a user

-configured

event is triggered. If a

user

-configured event does not

occur, the

fault circuit remains

closed.

Wiring the Redundant Power Inputs

The EDS-P510 has two sets of power inputs—power input 1 and power

input 2. The top two contacts and the bottom two contacts of the 6-pin

terminal block connector on the EDS-P510’s top panel are used for the

two digital inputs. The top and front views of one of the terminal block

connectors are shown here.

STEP 1: Insert the

negative/positive DC wires into

the V

/V+ terminals, respectively.

STEP 2:

To keep the DC wires

from pulling loose, use a small

flat

-blade screwdriver to tighten

the wire

clamp screws on the front

of the terminal block connector.

STEP 3:

Insert the p

lastic terminal

block connector prongs into the

terminal block receptor, which is

located on

the EDS-P510’s top

panel.

- 8 -

Wiring the Digital Inputs

The EDS-P510 has two sets of digital inputs, DI 1 and DI 2. Each DI

consists of two contacts of the 6-pin terminal block connector on the

EDS-P510’s top panel, which are used for the two DC inputs. The top and

front views of one of the terminal block connectors are shown here.

STEP 1: Insert the negative

(ground)/positive DI wires into the

┴

/I1 terminals, respectively.

STEP 2:

To keep the DI wires from

pulling loose, use a small

flat

-blade screwdriver to tighten

the wire

clamp screws on the front

of the terminal block connector.

STEP 3:

Insert the plastic terminal

block connector prongs into the

terminal bl

ock receptor, which is

located on

the EDS-P510’s top

panel.

Turbo Ring DIP Switch Settings

EDS-P510 series are plug-and-play managed redundant Ethernet

switches. The proprietary Turbo Ring protocol was developed by Moxa to

provide better network reliability and faster recovery time. Moxa Turbo

Ring’s recovery time is less than 300 ms (Turbo Ring) or 20 ms (Turbo

Ring V2) —compared to a 3- to 5-minute recovery time for commercial

switches—decreasing the possible loss caused by network failures in an

industrial setting.

There are 4 Hardware DIP Switches for Turbo Ring on the top panel of

EDS-P510 that can help setup the Turbo Ring easily within seconds. If you

do not want to use a hardware DIP switch to setup the Turbo Ring, you

can use a web browser, telnet, or console to disable this function.

NOTE

Please refer to the Turbo Ring DIP Switch section and Using

Communication Redundancy

section in User’s Manual for

more detail information about the settings and usage of

Turbo

Ring and Turbo Ring V2.

EDS-P510 Series DIP Switches

The default setting for each DIP Switch is OFF. The

following table explains the effect of setting the DIP

Switch to the ON position

- 9 -

“Turbo Ring” DIP Switch Settings

DIP 1

DIP 2

DIP 3

DIP 4

Reserved for

future use.

ON: Enables this

EDS as

the Ring

Master.

ON: Enables the

default “Ring

Coupling” ports.

ON: Activates DIP

switches 1, 2, 3 to

configure “Turbo

Ring” settings.

OFF: This EDS

will not be the

Ring Master.

OFF: Do not use

this EDS as the

ring coupler.

OFF: DIP

switches 1, 2, 3

will be disabled.

“Turbo Ring V2” DIP Switch Settings

DIP 1

DIP 2

DIP 3

DIP 4

ON: Enables the

default “Ring

Coupling

(backup)” port.

ON: Enables this

EDS as the Ring

Master.

ON: Enables the

default “Ring

Coupling” port.

ON: Activates

DIP switches 1,

2, 3 to configure

“Turbo Ring V2”

settings.

OFF: Enables the

default “Ring

Coupling

(primary)” port.

OFF: This EDS

will not be the

Ring Master.

OFF: Do not use

this EDS as a ring

coupler.

OFF: DIP

switches 1, 2, 3

will be disabled.

NOTE

You must enable the Turbo Ring function first before using the

DIP switch to activate the Master and Coupler functions.

NOTE

If you do not enable any of the EDS

P510 switches to be the Ring

Master, the Turbo Ring protocol

will automatically choose the

EDS

-P510 with the smallest MAC address range to be the Ring

Master. If you accidentally enable more than one EDS

P510 to be

the Ring Master, these EDS

-P510 switches will auto-

negotiate to

determine which one will be the Ring Master.

LED Indicators

The front panel of the Moxa EDS-P510 contains several LED indicators.

The function of each LED is described in the following table:

LED

Color

State

Description

PWR1 AMBER

Power is being supplied to power input

P1.

Off

Power is not being supplied to power

input P1.

PWR2 AMBER

Power is being supplied to power input

P2.

Off

Power is not being supplied to power

input P2.

FAULT RED

When a user-configured event is

triggered.

Off

When a user-configured event is not

triggered.

- 10 -

LED

Color

State

Description

MSTR/HEAD

GREEN

When the EDS-P510 is set as the

Master of the Turbo Ring, or as the

Head of the Turbo Chain.

Blinking

The EDS-P510 has become the Ring

Master of the Turbo Ring, or the Head

of the Turbo Chain, after the Turbo

Ring or the Turbo Chain is down.

Off

When the EDS-

P510 is not the Master

of this Turbo Ring or is set as the

Member of the Turbo Chain.

CPLR/TAIL GREEN

When the EDS-P510 coupling function

is enabled to form a back-

up path, or

when it's set as the Tail of the Turbo

Chain.

Blinking

When the Turbo Chain is down.

Off

When the EDS-P510 disables the

coupling function.

Port1 to

Port7 (10M)

AMBER

TP port’s 10 Mbps link is active.

Blinking

Data is being transmitted at 10 Mbps.

Off

TP port’s 10 Mbps link is inactive.

Port1 to

Port7

(100M)

GREEN

TP port’s 100 Mbps link is active.

Blinking

Data is being transmitted at 100

Mbps.

Off

TP port’s 100 Mbps link is inactive.

G1 to G3

(10/100M) AMBER

G1 to G3 port’s 10/100Mbps link is

active.

Blinking Data is being transmitted at

10/100Mbps.

Off

G1 to G3 port’s 10/100Mbps link is

inactive.

G1 to G3

(1000M) GREEN

G1 to G3 port’s 1000 Mbps link is

active.

Blinking Data is being transmitted at 1000

Mbps.

Off

G1 to G3 port’s 1000 Mbps link is

inactive.

PoE AMBER

Power is being supplied to Powered

Device (PD)

Blinking

PoE port is in Power-Fail status

Off

Power is not being supplied to

Powered Device (PD)

Autres manuels pour EtherDevice EDS-P510 Series

Table des matières

Autres manuels Moxa Technologies Changer

Moxa Technologies

Moxa Technologies EDS-516A Series Manuel

Moxa Technologies

Moxa Technologies EDS-316 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-P506E-4PoE Series Manuel utilisateur

Moxa Technologies

Moxa Technologies ICS-G7526 Series Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-405A-PTP Series Manuel

Moxa Technologies

Moxa Technologies MDS-G4000-L3-4XGS Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 1220 Manuel utilisateur

Moxa Technologies

Moxa Technologies TN-4516A non-PoE series Manuel utilisateur

Moxa Technologies

Moxa Technologies IKS-6324 Series Manuel

Moxa Technologies

Moxa Technologies EDS-2008-EL Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-505A Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-P206A-4PoE Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-G2005-EL Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-205A series Instructions de montage

Moxa Technologies

Moxa Technologies PT-7528-24TX-HV Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-510E Series Manuel utilisateur

Moxa Technologies

Moxa Technologies PowerTrans PT-7728-F-24 Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-405A Manuel utilisateur

Moxa Technologies

Moxa Technologies PT-7528 Manuel

Moxa Technologies

Moxa Technologies NPort 1220 Manuel utilisateur

Moxa Technologies

Moxa Technologies S9450I Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-408A Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-G4008 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies MDS-G4000-4XGS Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur