Moxa Technologies EDS-600 Series Manuel utilisateur

P/N: 1802006000017

*1802006000017*

EDS-600 Series

Quick Installation Guide

Moxa EtherDevice™ Switch

Version 5.3, March 2021

Technical Support Contact Information

www.moxa.com/support



- 2 -

Package Checklist

The Moxa EDS-600 Series is shipped with the following items. If any of

these items is missing or damaged, please contact your customer service

representative for assistance.

•1 EDS-600 EtherDevice Switch

•RJ45 to DB9 console port cable

•Protective caps for unused ports (Only for EDS-611 Series and

EDS-619 Series)

•Wall mounting kit (optional—must be ordered separately)

•Anti-vibration wiring kit (optional, must be ordered separately)

•Quick installation guide (printed)

•Warranty card

Features

Advanced Industrial Networking Capabilities

•IPv6 ready (certified by the IPv6 Logo Committee).

•IEEE 1588 PTP V2 (Precision Time Protocol) for precise time

synchronization of networks.

•Supports LLDP (Link Layer Discovery Protocol)

•DHCP Option 82 for IP address assignment with different policies.

•Supports Modbus/TCP industrial Ethernet protocol.

•Turbo Ring and Turbo Chain (< 20 ms recovery time) and STP/RSTP.

•IGMP snooping and GMRP for filtering multicast traffic.

•Port-based VLAN, IEEE 802.1Q VLAN, and GVRP to ease network

planning.

•QoS (IEEE 802.1p/1Q) and TOS/DiffServ to increase determinism.

•Port Trunking for optimal bandwidth utilization.

•IEEE 802.1X, HTTPS, and SSH to enhance network security.

•SNMPv1/v2c/v3 for different levels of network management.

•RMON for efficient network monitoring and proactive capability.

•Bandwidth management prevents unpredictable network status.

•Lock port function for blocking unauthorized access based on MAC

address.

•Port mirroring allows for online debugging.

•Automatic warning by exception through e-mail and relay output.

•Digital inputs to integrate sensors and alarms with IP networks.

- 3 -

Panel Views of the EDS-608

Front Panel:

1. System Status LEDs

2. Fast Ethernet Interface Module port LEDs

3. Fast Ethernet Interface Module

4. Terminal block for 2 power inputs, 1 DI/DO, and 1 relay output

5. Grounding screw

6. DIP switches for Ring Master, Ring Coupler, and Turbo Ring

7. RS-232 Console port

8. Screw to attach Fast Ethernet Interface Module

Rear Panel:

9. DIN-Rail Attachment Plate

10. Screw holes for wall mounting kit

- 4 -

Panel Views of the EDS-611

Front Panel:

1. System Status LEDs

2. Fast Ethernet Interface Module port LEDs

3. Fast Ethernet Interface Module

4. Terminal block for 2 power inputs, 1 DI/DO, and 1 Relay output

5. Grounding screw

6. DIP switches for Ring Master, Ring Coupler, and Turbo Ring

7. RS-232 Console port

G1 to G3: 10/100/1000 BaseT(X) or 100/1000Base SFP slot combo

ports

9. Screw to attach Fast Ethernet Interface Module

10.

Gigabit Ethernet LEDs

Rear Panel:

11.

DIN-Rail Attachment Plate

12. Screw holes for wall mounting kit

- 5 -

Panel Views of the EDS-616

Front Panel:

1. System Status LEDs

2. Fast Ethernet Interface Module port LEDs

3. Fast Ethernet Interface Module

4. Terminal block for 2 power inputs, 1 DI/DO, and 1 relay output

5. Grounding screw

6. DIP switches for Ring Master, Ring Coupler, and Turbo Ring

7. RS-232 Console port

8. Screw to attach Fast Ethernet Interface Module

Rear Panel:

9. DIN-Rail Attachment Plate

10. Screw holes for wall mounting kit

- 6 -

Panel Views of the EDS-619

Front

Panel:

1. System Status LEDs

2. Fast Ethernet Interface Module port LEDs

3. Fast Ethernet Interface Module

4. Terminal block for 2 power inputs, 1 DI/DO, and 1 relay output

5. Grounding screw

6. DIP switches for Ring Master, Ring Coupler, and Turbo Ring

7. RS-232 Console port

8. G1 to G3: 10/1

00/1000 BaseT(X) or 100/1000Base SFP slot combo

ports

9. Screw to attach Fast Ethernet Interface Module

10.

Gigabit Ethernet LEDs

Rear Panel:

11.

DIN-Rail Attachment Plate

12. Screw holes for wall mounting kit

- 7 -

Mounting Dimensions

EDS-608/EDS-611

- 8 -

EDS-616/EDS-619

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the

back panel of the EDS-600 when you take it out of the box. If you need to

reattach the DIN-Rail attachment plate to the EDS-600, be sure the

spring-loaded bracket is situated towards the bottom, as shown in the

following figures.

STEP 1:

If the spring

-loaded bracket is

locked in place, p

ush the recessed

button to release it. Once released,

you should feel some resistance

from the sp

ring as you slide the

bracket up and down a few

millimeters in each direction.

- 9 -

STEP 2:

Insert the top of the DIN

-Rail into

the

top slots on the DIN-Rail

attachment plate.

STEP 3:

The DIN

-Rail attachment unit will

snap into place as shown

in the

following illustration.

To remove the Moxa

EDS-600

switch

from the DIN

Rail, use a screwdriver

to push down the spring

-loaded

bracket until it locks in place, as

shown in the following diagram.

Next, rotate the bottom of the switch

upwards and

then remove the

switch from the DIN

-Rail.

Wall Mounting (Optional)

For some applications, you will find it convenient to mount the EDS-600

on the wall, as shown in the following illustrations:

STEP 1: Remove the aluminum DIN-Rail attachment plate from the rear

panel of the EDS-600, and then attach the wall mount plates with M3

screws, as shown in the figure at the right.

EDS-608/EDS-611

EDS-616/EDS-619

STEP 2: Mounting the EDS-600 on the wall requires 4

screws. Use the

EDS-600, with wall mount plates

attached, as a guide to mark the correct locations of the

4 screws. The heads of the screws should be less than

6.0 mm in diameter, and the shafts should be less than

3.5 mm in diameter, as shown in the figure at the right.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw through

one of the keyhole-shaped apertures of the Wall Mounting Plates.

- 10 -

Do not screw the screws in all the way—leave about 2 mm to allow room

for sliding the wall mount panel between the wall and the screws.

STEP 3: Once the screws are fixed to the wall, insert the four screw heads

through the wide parts of the keyhole-shaped apertures, and then slide

the EDS-600 downwards, as indicated in the figure at the right. Tighten

the four screws for more stability.

ATEX Information

1. Certificate number: DEMKO 11 ATEX 1007817X

2. Certification string: Ex nA nC IIC T4 Gc

3. Standards covered: EN 60079-0:2012+A11:2013, EN

60079-15:2010

4. Special Conditions of Use:

•Devices are to be installed in an ATEX certified Zone 2 enclosure

rated IP54 in accordance with EN 60529 that is accessible only

with the use of a tool.

•Devices are for use in an area of not more than pollution degree

2 in accordance with EN 60664-1.

•Provisions shall be made, external to the apparatus, to prevent

the rated voltage being exceeded by the transient disturbances

of more than 140%.

•Accessory Modules CM-600-4TX, CM-600-4MSC, CM-600-4SSC,

CM-600-4MST, CM-600-2MSC/2TX, CM-600-2SSC/2TX,

CM-600-3MSC/1TX, CM-600-3SSC/1TX must be used with

Models EDS-608, EDS-608-T, EDS-611, EDS-611-T, EDS-616,

EDS-616-T, EDS-619, and EDS-619-T.

•When customers use their own optical SFP communication

modules, these must be limited to Laser Class 1 only in

accordance with EN 60825-1.

Autres manuels pour EDS-600 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Moxa Technologies Changer

Moxa Technologies

Moxa Technologies PT-510 Series Manuel

Moxa Technologies

Moxa Technologies TRC-190 Manuel utilisateur

Moxa Technologies

Moxa Technologies PowerTrans PT-7828 Manuel

Moxa Technologies

Moxa Technologies PT-G7509 Manuel utilisateur

Moxa Technologies

Moxa Technologies ToughNet TN-5510-2GLSX-ODC Manuel

Moxa Technologies

Moxa Technologies EDS-316 EtherDevice Manuel

Moxa Technologies

Moxa Technologies PT-G7728 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPORT 6610 Manuel utilisateur

Moxa Technologies

Moxa Technologies ICS-G7748A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies TN-5500A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies TN-4516A non-PoE series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-505A Manuel

Moxa Technologies

Moxa Technologies EDS-G4014 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies TN-G6512 Serie Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice Switch EDS-G205 Manuel

Moxa Technologies

Moxa Technologies EDS-316 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies UPORT 1200 series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4POE-1GSFP-T Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-P206A-4PoE-SS-SC Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-305-T Manuel

Moxa Technologies

Moxa Technologies TN-5305-T Manuel utilisateur

Moxa Technologies

Moxa Technologies PowerTrans PT-7528-24TX-WV Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-2010-ML Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-516A Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur