Moxa Technologies TN-G6512 Serie Manuel utilisateur

P/N: 1802065120010

*1802065120010*

TN-G6512 Series

Quick Installation Guide

Moxa ToughNet Switch

Edition 1.0, December 2018

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The ToughNet TN-G6512 series of M12 managed Ethernet switches are

designed for railway applications, including rolling stock and wayside

installations. The switches use M12 and other circular connectors to

ensure tight, robust connections, and guarantee reliable operation in

industrial environments where vibration and shock are commonplace.

The TN-G6512 series of Ethernet switches provide 12 gigabit Ethernet

M12 ports; 8 ports support IEEE 802.3at/af compliant PoE functionality.

These PoE switches are classified as power source equipment (PSE); they

provide up to 30 watts of power per port, and can be used to power IEEE

802.3at/af compliant powered devices (PDs), such as IP cameras,

wireless access points, and IP phones.

The TN-G6512 Series has push-pull M12 connectors that are tailor-made

for push-pull cables in order to facilitate quick installation, and also allow

M12 rotary cables to be utilized. The 24 to 110 VDC wide power input

range and isolated dual power inputs not only allow the same type of

power source at different sites around the globe, but also increase the

reliability of communications systems. Furthermore, the -40 to 70°C

operating temperature capability and IP67-rated enclosure make the

switches suitable for deployment in harsh environments. The TN-G6512

series of Ethernet switches are compliant with the essential sections of EN

50155, covering operating temperature, power input voltage, surge, ESD,

and vibration, as well as conformal coating and power insulation, which

makes the switches suitable for a variety of industrial applications.

Package Checklist

Your ToughNet TN-G6512 switch is shipped with the following items. If

any of these items are missing or damaged, please contact your customer

service representative for assistance.

•TN-G6512 switch

•M12-to-DB9 console port cable

•15 protective caps for the power connector, all Ethernet ports,

console port, and USB storage port (already fixed on switch)

•Panel mounting kit

•Quick installation guide (printed)

•Warranty card

Features

Anti-Vibration Push-Pull/Circular Connectors for Robust Links

•M12 X-coded 8-pin female connectors for gigabit Ethernet

10/100/1000BaseT(X) ports

•M12 B-coded 5-pin female connector for serial console port

•M12 A-coded 5-pin female connector for USB storage port

•M12 K-coded 5-pin male connector for power input

Isolated Power Inputs

•Supports 24 to 110 VDC (16.8 to 137.5 VDC)

High Performance Network Switching Technology

•Provides up to 30 watts per PoE port with a total power budget of 96

watts per switch

•IPv6 Ready logo awarded (IPv6 Logo Committee certified)

•DHCP Option 82 for IP address assignment with different policies

- 3 -

•Turbo Ring and Turbo Chain (recovery time < 50 ms @ 250 switches),

and STP/RSTP/MSTP for network redundancy

•IGMP snooping and GMRP for filtering multicast traffic

•EtherNet/IP and Modbus/TCP industrial Ethernet protocols supported

•Port-based VLAN, IEEE 802.1Q VLAN, and GVRP to ease network

planning

•QoS (IEEE 802.1p/1Q and ToS/DiffServ) allows real-time traffic

classification and prioritization

•IEEE 802.3ad, LACP for optimum bandwidth utilization

•SNMPv1/v2c/v3 for different levels of network management

•TACACS+, SNMPv3, IEEE 802.1X, HTTPS, and SSH to enhance

network security

•RMON for efficient network monitoring and proactive capability

•Bandwidth management prevents unpredictable network status

•Lock port allows access by only authorized MAC addresses

•Port mirroring for online debugging

•Automatic warning by exception through email and relay output

•Line-swap fast recovery

•LLDP for automatic topology discovery in network management

software

•Configurable by web browser, Telnet/serial console, CLI, and

Windows utility

•Loop protection prevents network loops

Designed for Industry-Specific Applications

•Twelve Gigabit Ethernet ports to meet high bandwidth requirements.

•Complies with all EN 50155 mandatory test items*

•-40 to 70°C operating temperature range

•IP67-rated rugged case

•Panel mounting installation capability

*This product is suitable for rolling stock railway applications, as defined

by the EN 50155 standard. For a more detailed statement, click here:

www.moxa.com/doc/specs/EN_50155_Compliance.pdf

Recommended Optional Accessories

•CBL-M12XMM8PRJ45-Y-200-IP67: 2-meter M12-to-RJ45 Cat-5 UTP

Ethernet cable with IP67-rated 8-pin male X-coded crimp type M12

connector

•CBL-M12XMM8P-Y-300-IP67: 3-meter M12-to-M12 Cat-5 UTP

Ethernet cable with IP67-rated 8-pin male X-coded crimp type M12

connector

•CBL-M12XMM8P-Y-100-IP67: 1-meter M12-to-M12 Cat-5 UTP

Ethernet cable with IP67-rated 8-pin male X-coded crimp type M12

connector

•M12X-8PMM-IP67-HTG: Field-installable M12 X-coded crimp type,

slim design connector, 8-pin male, IP67-rated

•A-CAP-M12F-M-PP: Metal Cap for M12 female push-pull connector

- 4 -

Panel Layouts

1. Screw holes for panel

mounting kit

2. Console port

3. USB port

4. FAULT LED

5. PWR1 LED:

for power input 1

6. PWR2 LED:

for power input 2

10/100/1000BaseT(X) port

(M12 X-coded 8-

pin female

connector)

10/100/1000BaseT(X) port

LED

9. PoE LED

10.

Grounding screw

11.

Power input port (M12

K-coded 5-pin male

connector)

12.

CPLR/TAIL LED: for ring

coupler or chain tail

13.

MSTR/HEAD LED: for ring

master or chain head

14.

Alignment mark for

X-coded connector

15.

Waterproof vent

ATTENTION

Exposed connectors when not in use must be tightly covered with

protective caps (an optional accessory) to ensure IP

67-rated

protection.

- 5 -

Mounting Dimensions (unit = mm)

- 6 -

Panel/Wall Mounting

STEP 1: Mounting the TN-G6512 to a wall requires 4 screws. Use the

ToughNet switch as a guide to mark the correct positions of the 4 screws.

STEP 2: Use the 4 screws in the

panel mounting kit. If you

would like

to use your own screws, make sure

the screw head

between 6.0 mm

and 7.0 mm

in diameter and the

shaft

is less than 4.0 mm in

diameter, as shown

at the right.

Do not screw the screws in all the way—leave a space of about 2 mm to

allow room for sliding the ToughNet switch between the wall and the

screws.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shaft size are suitable by inserting the screw through

one of the keyhole-shaped apertures of the ToughNet switch.

STEP 3: Once the screws are fixed in the wall, hang the ToughNet switch

on the 4 screws through the large opening of the keyhole-shaped

apertures, and then slide the switch downwards. Tighten the four screws

for added stability.

NOTE

To provide greater protection from vibration and shock, use

screws with shaft diameter between 6.0 mm and 7.0 mm, and fix

the ToughNet switch onto the wall directly through the large

opening of the keyhole-shaped apertures.

Wiring Requirements

WARNING

Turn the power off before disconnecting modules or wires. The

correct power supply voltage is listed on the product label. Check

the voltage of your power source to make sure you are using the

correct voltage. Do NOT use a voltage great

er than what is

specified on the product label.

These devices must be supplied by a SELV source as defined in

the Low Voltage Directive 2006/95/EC and 2004/108/EC.

- 7 -

ATTENTION

Safety First!

Be sure to disconnect the power

cord before installing and/or

wiring your Moxa switch.

This device has UL 61010-2-201

approval. Use copper conductors only,

°C, and tighten to 4.5

pound-inches. For use in pollution degree 2 environments.

ATTENTION

Safety First!

Observe all electrical codes dictating the

maximum current

allowable for each wire size. If the current

goes above the

maximum ratings, the wiring could overheat,

causing serious

damage to your equipment.

Please read and follow these guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together.

•Keep input wiring and output wiring separated.

•It is strongly advised that you label wiring for all devices in the system

when necessary.

Grounding the ToughNet Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

grounding screw to the grounding surface prior to connecting devices.

- 8 -

ATTENTION

This product

is intended to be mounted to a well-grounded

mounting surface such as a metal panel.

Connecting the Power Supplies

ToughNet TN-G6512 series switches support dual power inputs—power

input 1 and power input 2. The M12 K-coded 6-pin male connector on the

TN-G6512 series switches' front panel is used for the dual power inputs.

Pinouts for the power input port

PWR

V1+

V1–

V2–

V2+

GND

Description

Usage

1 PWR1 / DC +

Connect “PWR1 Live / DC +” to the positive (+)

terminal when using a DC power source.

2 PWR1 / DC –

Connect “PWR1 Neutral / DC –” to the negative (–)

terminal when using a DC power source.

3 PWR2 / DC – Connect “PWR2 Neutral / DC –” to the negative (–

)

terminal when using a DC power source.

4 PWR2 / DC +

Connect “PWR2 Live / DC +” to the positive (+)

terminal when using a DC power source.

PE Chassis Ground

Connect the “Chassis Ground” to the equipment

ground bus for DC inputs.

STEP 1: Plug your power cord connector into the power input port of the

TN-G6512 switch.

STEP 2: Screw the nut on your power cord connector into the power input

connector on the switch to ensure a tight connection.

ATTENTION

Before connecting the

TN-G6512

series to the power input, make

sure the power source voltage is stable.

ATTENTION

Do not power on

the TN-G6512 series before connecting the M1

power connector.

- 9 -

Connecting the Data Lines

10/100/1000BaseT(X) Ethernet Port Connection

The TN-G6512 Series has 12 10/100/1000BaseT(X) Ethernet ports (M12

X-coded 8-pin female connector). The 10/100/1000TX ports located on

the front panel of the TN-G6512 Series are used to connect to

Ethernet-enabled devices. Most users configure these ports for Auto

MDI/MDI-X mode, in which case the port’s pinouts are adjusted

automatically depending on the type of Ethernet cable used

(straight-through or cross-over), and the type of device (NIC-type or

HUB/Switch-type) connected to the port.

In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports. We also give cable wiring diagrams for

straight-through and cross-over Ethernet cables.

Pinouts for the 10/100/1000BaseT(X) M12 (8-pin) Port

M12 (8-pin, M) to M12 (8-pin, M) Cross-Over Cable Wiring

- 10 -

M12 (8-pin, M) to M12 (8-pin, M) Straight-Trough Cable Wiring

M12 (8-pin, M) to RJ45 (8-pin) Cross-Over Cable Wiring

M12 (8-pin, M) to RJ45 (8-pin) Straight-Trough Cable Wiring

Table des matières

Autres manuels Moxa Technologies Changer

Moxa Technologies

Moxa Technologies TN-4516A non-PoE series Manuel utilisateur

Moxa Technologies

Moxa Technologies MDS-G4000 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies ToughNet TN-5816A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies IEX-408E-2VDSL2 series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A Series Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-728 Series Manuel

Moxa Technologies

Moxa Technologies UPort 404 Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-G2005-EL Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-2005-ELP Series Manuel utilisateur

Moxa Technologies

Moxa Technologies SPL-24 Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A Series Manuel

Moxa Technologies

Moxa Technologies ICS-G7526 Series Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-G509 Manuel

Moxa Technologies

Moxa Technologies EDS-508 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-G508E-T Manuel

Moxa Technologies

Moxa Technologies EDS-G308 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510-T Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-316 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies PowerTrans PT-7728-PTP Manuel

Moxa Technologies

Moxa Technologies PT-G7728 Manuel utilisateur

Moxa Technologies

Moxa Technologies TN-5305-T Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4PoE-1GSFP Manuel

Moxa Technologies

Moxa Technologies MDS-G4000 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-208 series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur