Moxa Technologies EDS-316 Series Manuel utilisateur

P/N: 1802003160015

*1802003160015*

EDS-316 Series

Quick Installation Guide

Moxa EtherDevice Switch

Version 6.2, January 2021

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

The Moxa EtherDevice™ EDS-316 series of 16-port smart Ethernet

switches provides an economical solution for your Ethernet connections.

As an added bonus, the built-in smart alarm function helps system

maintainers monitor the health of your Ethernet network.

EDS-316 has a wide operating temperature range of -40 to 75°C, and is

designed to withstand a high degree of vibration and shock. The rugged

hardware design makes EDS-316 series perfect for ensuring that your

Ethernet equipment can withstand critical industrial applications, such as

in hazardous locations (Class 1 Division 2/ Zone 2), and complies with

FCC, TÜV, UL, and CE Standards.

NOTE

Throughout this Hardware Installation Guide, we use EDS as an

abbreviation for Moxa EtherDevice Switch:

EDS = Moxa EtherDevice Switch

Package Checklist

Moxa EDS-316 is shipped with the following items. If any of these items is

missing or damaged, please contact your customer service

representative for assistance.

•Moxa EtherDevice™ Switch

•Protective caps for unused ports

•Quick installation guide (printed)

•Warranty card

Features

High Performance Network Switching Technology

•10/100BaseT(X) (RJ45), 100BaseFX (SC/ST type, Multi/Single mode)

•IEEE 802.3/802.3u/802.3x

•Store and Forward switching process type, with 4K address entries

•10/100M, Full/Half-Duplex, MDI/MDIX auto-sensing

Industrial Grade Reliablity

•Power failure, port break alarm by relay output

•Redundant dual DC power inputs

•Broadcast storm protection to prevent network devices from crashing

Rugged Design

•Operating temperature range of 0 to 60°C, or extended operating

temperature of -40 to 75°C for (-T) models

•IP30, rugged high-strength case

•DIN-Rail or wall mounting ability

- 3 -

Panel Layout of EDS-316 (standard-type)

1. Grounding screw

2. Terminal block for power input

(PWR1, PWR2) and relay output

3. Heat dissipation orifices

4. DIP switches

(EDS-316 has 18 DIP switches

total; 1 DIP switch is reserved)

5. Power input PWR1 LED

6. Power input PWR2 LED

7. Fault LED

8. 10/100BaseT(X) Port

9. TP port’s 100 Mbps LED

10.

TP port’s 10 Mbps LED

11.

Model Name

12.

Screw hole for wall mounting kit

13.

DIN-Rail Kit

- 4 -

Panel Layout of EDS-316 (SC-type)

Product models not shown here:

EDS

-316-S-SC is identical to

EDS

-316-M-SC.

EDS

-316-SS-SC and EDS-316-MS-

are identical to

EDS-316-MM-SC.

1. Grounding screw

2. Terminal block for power input

(PWR1, PWR2) and relay output

3. Heat dissipation orifices

4. DIP switches (EDS-316 series has

18 DIP switches in total; 1 DIP

switch is reserved)

5. Power input PWR1 LED

6. Power input PWR2 LED

7. Fault LED

8. 10/100BaseT(X) Port

9. TP port’s 100 Mbps LED

10.

TP port’s 10 Mbps LED

11.

Model Name

12.

100BaseFX Port

SSC for EDS-316-MS-SC

SSC-80 for EDS-316-SS-SC-40/80

13.

100BaseFX Port

MSC for EDS-316-MS-SC

SSC-40 for EDS-316-SS-SC-40/80

14.

FX port’s 100 Mbps LED

15.

Screw hole for wall mounting kit

16.

DIN-Rail Kit

NOTE

MSC = Multi-Mode SC Connector

SSC

= Single-Mode SC Connector

SSC-80 = Single-Mode SC Connector (80 km)

- 5 -

Panel Layout of EDS-316 (ST-type)

1. Grounding screw

2. Terminal block for power input

(PWR1, PWR2) and relay output

3. Heat dissipation orifices

4. DIP switches

(EDS-316 has 18 DIP switches in

total; 1 DIP switch is reserved)

5. Power input PWR1 LED

6. Power input PWR2 LED

7. Fault LED

8. 10/100BaseT(X) Port

9. TP port’s 100 Mbps LED

10.

TP port’s 10 Mbps LED

11.

Model Name

12.

100BaseFX Port

13.

FX port’s 100 Mbps LED

14.

Screw hole for wall mounting kit

15.

DIN-Rail Kit

- 6 -

Mounting Dimensions

Unit = mm (inch)

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the

back panel of EDS-316 when you take it out of the box. If you need to

reattach the DIN-Rail attachment plate, make sure the stiff metal spring

is situated towards the top, as shown in the figures below.

STEP 1:

Insert the top of the DIN

-Rail into

the slot just

below the stiff metal

spring.

STEP 2:

The DIN

-Rail attachment unit will

snap into place as shown below.

To remove Moxa EtherDevice Switch from the DIN-Rail, simply reverse

Steps 1 and 2 above.

- 7 -

Wall Mounting (optional)

For some applications, you will find it convenient to mount EDS-316 on

the wall, as illustrated in the figure.

STEP 1: Remove the

aluminum DIN

-Rail

attachment plate from

EDS

-316’s rear panel, and

then attach the wall mount

plates, as shown in the

figu

re.

STEP 2:

Mounting EDS-316 on the wall requires 4

screws. Use the

switch, with wall mount plates

attached, as a guide to mark the correct locations of the

4 screws. The heads of the screws should

be less than

6.0 mm in diameter, and the shafts should be less than

3.5 mm in diameter, as shown in the figure at the right.

NOTE

Before tightening screws into the wall, make sure the screw head

and shank size are suitable by inserting the screw into one of the

keyhole-shaped apertures of the Wall Mounting Plates.

Do not screw the screws in all the way—leave about 2 mm to allow room

for sliding the wall mount panel between the wall and the screws.

STEP 3: Once the screws are fixed

in the wall, insert

the four screw

heads through the large parts of

the keyhole

-shaped apertures,

and then slide EDS

-316

downwards, as indicated. Tighten

the four screws for

added

stability.

ATTENTION

The equipment shall be installed in a

n enclosure that is only

accessible using the correct tool with at least

an IP54 rating in

accordance with IEC/EN 60079

-15. It should not be used in an

area with pollution degree 2 or higher as defined in IEC 60664-1.

These devices are open-type devices that are to be installed in an

enclosure only accessible with the use of a correct tool. This equipment is

only suitable for use in Class I, Division 2, Groups A, B, C and D or

non-hazardous locations.

- 8 -

WARNING

EXPLOSION HAZ

ARD – Servicing, replacing, and installing the

product can only take place is an area that is non-hazardous.

ATEX Information

1. Certificate number DEMKO 09 ATEX 0812123X

2. Ambient range: 0°C to 60°C (For suffix without–T), -40°C to 75°C

(For suffix with–T)

3. Certification string: Ex nA nC IIC T4 Gc

4. Rated Cable Temperature: ≧100°C

5. Standards covered:

EN 60079-0:2012+A11:2013, EN 60079-15:2010

6. The conditions of safe usage:

•These products must be mounted in an IP54 enclosure.

•Install in an area of pollution degree 2 or less.

•Use a conductor wire of size 0.2 mm² or greater.

•Conductors suitable for use in an ambient temperature of 93°C

must be used for the Power Supply Terminal.

•PROVISIONS SHALL BE MADE, EITHER IN EXTERNAL TO THE

APPARATUS, TO PREVENT THE RATED VOLTAGE BEING

EXCEEDED BY THE TRANSIENTS DISTURBANCES OF MORE

THAN 40 %

Wiring Requirements

WARNING

EXPLOSION HAZARD

- Substitution of any components may

impair suitability for Class I, Division 2.

WARNING

Do not disconnect modules or wires unless the power supply has

been switched off or the area is known to be non

-hazardous.

The

devices may only be connected to the supply voltage shown on

the type plate.

The devices a

re designed for operation with a Safety Extra-L

Voltage. Thus, they may only be connected to the supply voltage

connections and to the signal contact with the

Safety Extra-L

Voltages (SELV) in compliance with IEC950/ EN60950/ VDE0805.

- 9 -

WARNING

Substitution of components may impair suitability for Class

Division 2

, and Zone 2. These devices must be supplied by an

SELV source as defined in Low Voltage Directive 73/23/EEC and

93/68/EEC.

WARNING

This unit is a built

-in type. When the unit is installed in another

piece of equipment, the equipment enclosing the unit must

comply with fire enclosure regulation IEC 60950/EN60950 (or

similar regulation).

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your

Moxa EtherDevice Switch.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes

dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

You should also pay attention to the following items:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together.

•Keep input wiring and output wiring separated.

•It is strongly advised that you label wiring to all devices in the system

when necessary.

•Only use copper conductors with 60/75°C capability

Grounding Moxa EtherDevice Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices. A

4mm 2 conductor must be used when a connection to the external

grounding screw is utilized.

- 10 -

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface, such as a metal panel.

Wiring the Alarm Contact

The Alarm Contact consists of the two middle contacts of the terminal

block on EDS’s top panel. You may refer to the next section for detailed

instructions on how to connect the wires to the terminal block connector,

and how to attach the terminal block connector to the terminal block

receptor.

In this section, we explain the meaning of the two contacts used to

connect the Alarm Contact.

FAULT: The two middle contacts of the 6-contact

terminal block connector

are used to detect both

power faults and port faults. The two wires attached

to the Fault contacts

form an open circuit when:

1. EDS has lost power from one of the DC power

inputs.

The PORT ALARM DIP Switch for one of the ports

is set to ON, but the port is not connected

properly.

neither of these two conditions is satisfied, the

Fault circuit will be closed.

Wiring the Redundant Power Inputs

The top two contacts and the bottom two contacts of the 6-contact

terminal block connector on EDS’s top panel are used for EDS’s two DC

inputs. Top and front views of one of the terminal block connectors are

shown here.

STEP 1:

Insert the negative/positive DC wires into

the

V-/V+ terminals.

STEP 2:

To keep the DC wires from pulling

loose, use

a small flat

-blade screwdriver to tighten the

wire

clamp screws on the front of the terminal block

connector.

STEP 3:

Insert the plastic terminal block connector

prongs into the terminal block receptor, which is

located on

EDS’s top panel.

ATTENTION

Before connecting EDS to the DC power inputs, make sure the DC

power source voltage is stable.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Moxa Technologies Changer

Moxa Technologies

Moxa Technologies PT-G7509 Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-405A-PTP Series Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-P206A-4PoE Series Manuel utilisateur

Moxa Technologies

Moxa Technologies ToughNet TN-4500A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies UPORT 1200 series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-510E Series Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-P506A-4PoE Series Manuel utilisateur

Moxa Technologies

Moxa Technologies PT-G7728 Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-P308 Series Manuel

Moxa Technologies

Moxa Technologies PT-G7828 Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-516A-T Manuel

Moxa Technologies

Moxa Technologies NPort 1220 Manuel utilisateur

Moxa Technologies

Moxa Technologies ICS-G7748A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies TN-G6512 Serie Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-G308 Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205-T Manuel

Moxa Technologies

Moxa Technologies ToughNet TN-5524-8PoE-P24-T Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4PoE Manuel utilisateur

Moxa Technologies

Moxa Technologies ToughNet TN-5510A-2GLSX-ODC Manuel

Moxa Technologies

Moxa Technologies IKS-6726-8PoE Series Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-P206A-4PoE Series Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A-T Manuel

Moxa Technologies

Moxa Technologies EDS-510E Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur