Moxa Technologies EDS-2010-ML Series Manuel utilisateur

P/N: 1802020003011

*1802020003011*

EDS-2010/2018-ML Series

Quick Installation Guide

Moxa EtherDevice Switch

Version 1.1, August 2019

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The EDS-2010/2018-ML series of industrial Ethernet switches are

equipped with 8/16-ports 10/100M copper ports and 2

10/100/1000BaseT(X) or 100/1000BaseSFP combo ports. The switches

are ideal for applications that require high-bandwidth data convergence

and long-distance uplinks.

The EDS-2010/2018-ML provides 12/24/48 VDC redundant power

inputs, and the switches are available with a standard operating

temperature range from -10 to 60°C, or with a wide operating

temperature range from -40 to 75°C. The switches are rugged enough

to operate reliably in harsh industrial environments.

To provide greater versatility for use with applications from different

industries, the EDS-2010/2018-ML also allow users to enable or disable

broadcast storm protection, Quality of Service (QoS) function, and port

break alarm function with DIP switches on the outer panel.

The EDS-2010/2018-ML switches can be easily installed with DIN-Rail

mounting as well as distribution boxes. The DIN-rail mounting

capability and IP30 metal housing with LED indicators make the plug-

and-play EDS-2010/2018-ML switches reliable and easy to use.

NOTE

Throughout this Quick Installation Guide, we use EDS as an

abbreviation for Moxa EtherDevice Switch:

EDS = Moxa EtherDevice Switch

ATTENTION

This device complies with part 15 of FCC Rules. Operation is

subject

to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

Package Checklist

Your EDS is shipped with the following items. If any of these items are

missing or damaged, please contact your customer service

representative for assistance.

•Moxa EtherDevice™ Switch

•Quick installation guide (printed)

•Warranty card

•Protective caps for unused ports

- 3 -

Features

High Performance Network Switching Technology

•10/100/1000BaseT(X), 10/100BaseT(X) auto-negotiation speed,

full/half duplex mode, auto MDI/MDI-X connection, and

100/1000Base SFP slot.

•IEEE 802.3 for 10BaseT, IEEE 802.3u for 100BaseT(X), IEEE

802.3ab for 1000BaseT, and IEEE 802.3z for 1000BaseX.

•IEEE 802.1p for Quality of Service (QoS) traffic prioritized function.

•Store-and-forward switching process type.

Industrial-grade Reliability

•Power failure, port break alarm by relay output

•Redundant dual DC power inputs

•Broadcast storm protection to prevent network devices from

crashing

Rugged Design

•Operating temperature range from -10 to 60°C, or extended

operating temperature from -40 to 75°C for “-T” models

•IP30, rugged high-strength case

•DIN-rail or panel mounting ability

WARNING

The

power for this product is intended to be supplied by a

Listed Power Supply, with output marked LPS, and rated to

deliver 12 to 48 VDC at a maximum

of 0.62 A.

The DC

jack should be used with an LPS unit that is rated to

deliver 12 to 48 VDC at a minimum of 1.1A. The product should

not be disassembled by operators or service people.

- 4 -

Panel Layout of EDS-2010-ML-2GTXSFP / EDS-

2018-ML-2GTXSFP

1. Grounding screw

2. Terminal block for power input

(PWR1, PWR2) and relay output

3. DIP switch

4. Power input PWR1 LED

5. Power input PWR2 LED

6. Fault LED

7. Port number

8. 10/100 BaseT(X) Port

9. TP port’s 100 Mbps LED

10. TP port’s 10 Mbps LED

11. 10/100/1000 BaseT(X) Port

12. TP port’s 1000 Mbps LED

13. TP port’s 100 Mbps LED

14. 100/1000Base SFP slot

15. SFP port's 100/1000 Mbps LED

16. Model Name

- 5 -

Mounting Dimensions

EDS-2010-ML Series

EDS-2018-ML Series

- 6 -

DIN-rail Mounting

There are two options for DIN-rail mounting that can be used on an

EDS. Option 1 is the default type when the product is shipped.

Option 1 (Default):

When shipped, the metal DIN-rail mounting kit is fixed to the back

panel of the EDS. Mount the EDS on the corrosion-free mounting rail

that adheres to the EN 60715 standard.

Suggested Installation Method

STEP 1:

Insert the upper lip of the DIN

rail kit into the mounting rail.

TEP 2:

Press the device towards the

mounting rail until it snaps into

place.

Suggested Removal Method

STEP 1:

Pull down the latch on the DIN

rail kit with a screwdriver.

STEP 2:

Slightly pull the device forward

and lift up to remove it from the

mounting rail.

Option 2 (when side cabling is needed):

The metal DIN-rail mounting kit can be fixed to the side panel (mold

side) of the EDS (horizontal or vertical). Mount the EDS on the

corrosion-free mounting rail that adheres to the EN 60715 standard.

- 7 -

Suggested Installation Method

STEP 1:

Detach the metal DIN-rail mounting kit from the back panel and attach

it to the side panel (mold side) in either the horizontal or vertical

direction as indicated in the figure below.

STEP 2:

Insert the upper lip of the DIN

-rail kit

into the mounting rail.

STEP 3:

Press the device towards the mounting

rail until it snaps into place

Suggested Removal Method

STEP 1:

Pull down the latch

on the DIN-rail kit

with a screwdriver.

STEP 2:

Slightly pull the device forward and lift

up to remove it from the mounting rail.

NOTE

Screws that are used to fix the DIN-rail kit on the EDS should

be securely fastened before mounting on the mounting

rail.

Please make sure that if you remove the DIN

-rail, it must be

securely fastened when it is reattached.

- 8 -

Wall Mounting (optional)

For some applications, you will find it convenient to mount EDS on the

wall, as illustrated below.

STEP 1:

Remove the aluminum DIN-Rail attachment plate from EDS’s rear

panel, and then attach the wall mount plates, as shown in the diagram

below.

EDS-2010-ML Series

EDS-2018-ML Series

STEP 2:

Mounting EDS

on the wall requires 4 screws. Use the

switch, with wall mount plates attached, as a guide

to mark the correct locations of the 4 screws. The

heads of the screws should be less than 6.0 mm in

diameter, and the shafts should be less than 3.5 mm

in diameter, as shown in the figure at the right.

NOTE

Before tightening screws into the wall, make sure the screw

head and shank size are suitable by inserting th

e screw into

one of the keyhole

-shaped apertures of the Wall Mounting

Plates.

Do not screw the screws in all the way—leave about 2 mm to allow

room for sliding the wall mount panel between the wall and the screws.

STEP 3:

Once the screws are fixed in the

wall, insert the four screw heads

through the large parts of the

keyhole

-shaped apertures, and

hen slide EDS downwards, as

indicated. Tighten the four

screws for added stability.

WARNING

External metal parts are hot. Take necessary precautions if

it is necessary to touch.

- 9 -

Wiring Requirements

WARNING

Do not

disconnect modules or wires unless the power supply

has been switched off or the area is known to be non

hazardous.

The devices may only be connected to the supply

voltage shown on the type plate.

The devices are designed for operation with a

Safety Extra-L

oltage. Thus, they may only be connected to the supply

voltage connections and to the signal contact with the

Safety

xtra-Low Voltages (SELV) in compliance with IEC950/

EN60950/ VDE0805.

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your

Moxa EtherDevice Switch.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire

size.

If the current goes above the maximum ratings, the wiring

could overheat, causing serious damage to your equipment.

You should also pay attention to the following items:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power

wiring in the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb

is that wiring that shares similar electrical characteristics can be

bundled together.

•Keep input wiring and output wiring separated.

•It is strongly advised that you label wiring to all devices in the

system when necessary.

- 10 -

Grounding Moxa EtherDevice Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from

the ground screw to the grounding surface prior to connecting devices.

A 4 mm2conductor must be used when a connection to the external

grounding screw is utilized.

ATTENTION

This

product is intended to be mounted to a well-grounded

mounting surface, such as a metal panel.

Wiring the Alarm Contact

The Alarm Contact consists of the two middle contacts of the terminal

block on EDS’s top panel. You may refer to the next section for detailed

instructions on how to connect the wires to the terminal block

connector, and how to attach the terminal block connector to the

terminal block receptor. In this section, we explain the meaning of the

two contacts used to connect the Alarm Contact.

FAULT: The two middle contacts of the 6-

contact

terminal block connector are used to

detect both power faults and port faults. The

two wires attached to the Fault contacts form

n open circuit when:

1. The EDS has lost power from one of the

DC power inputs.

2. One of the ports for which the

corresponding PORT ALARM DIP Switch

is set to ON is not properly connected.

neither of these two conditions is satisfied,

the Fault circuit will be closed.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Moxa Technologies Changer

Moxa Technologies

Moxa Technologies TN-5516A Series Manuel

Moxa Technologies

Moxa Technologies PT-G510 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EDS-G4014 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies TN-G4516-8GPoE-4XGPoE-WV-T Manuel utilisateur

Moxa Technologies

Moxa Technologies PowerTransPT-7728-PTP Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-2016-ML Series Manuel utilisateur

Moxa Technologies

Moxa Technologies TN-4516A non-PoE series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-4012 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-828 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies PT-G7728 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 1220 Manuel utilisateur

Moxa Technologies

Moxa Technologies NE-4100 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies IEX-408E-2VDSL2 series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510A-8PoE Series Manuel

Moxa Technologies

Moxa Technologies EDS-516A Series Manuel

Moxa Technologies

Moxa Technologies EDS-516A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A Series Manuel

Moxa Technologies

Moxa Technologies UPORT 1200 series Manuel utilisateur

Moxa Technologies

Moxa Technologies PT-7710 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-4009 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-208A series Manuel

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A Series Manuel

Moxa Technologies

Moxa Technologies PowerTrans PT-7528-24TX-WV Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice EDS-405A-PTP Series Manuel

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur