M-system R3S-RS4A Manuel utilisateur
R3S-RS4A
P. 1 / 3EM-8936
RTD INPUT MODULE
(high accuracy, 4 points, isolated) MODEL R3S-RS4A
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
RTD input module........................................................ (1)
■MODEL NO.
Confirm that the model number described on the product is
exactly what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■HOT INSERTION/REMOVAL OF MODULES
Removing or replacing modules does not affect other mod-
ules on the same backplane. It is possible to replace them
without removing the power supply. However, replacing
multiple modules at once may greatly change line voltage
levels. We recommend that you replace them one by one.
■ENVIRONMENT
•Indooruse
•Whenheavydustormetalparticlesarepresentintheair,
install the unit inside proper housing with sufficient ven-
tilation.
•Donotinstalltheunitwhereitissubjectedtocontinuous
vibration.Donotsubjecttheunittophysicalimpact.
•Environmentaltemperaturemustbewithin-10to+55°C
(14to131°F)withrelativehumiditywithin30to90%RH
in order to ensure adequate life span and operation.
■WIRING
•Do not install cables (power supply, input and output)
close to noise sources (relay drive cable, high frequency
line, etc.).
•Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
The unit is designed to function as soon as power is sup-
plied,however,awarmupfor10minutesisrequiredforsat-
isfying complete performance described in the data sheet.
INSTALLATION
Use the Installation Base (model: R3-BSx).
COMPONENT IDENTIFICATION
1
20
■ FRONT VIEW
RUN LED
ERR LED
SW2SW1
ON ON
SW3
Input 2 (SW1)
or
Input 4 (SW2)
RTD
Conv.
Rate
Temp.
Unit
Burnout
■ SIDE VIEW
Input 1 (SW1)
or
Input 3 (SW2)
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
ON
4
3
2
1
R3S-RS4A
P. 2 / 3EM-8936
■INDICATORS
RUN indicator:Bi-color(red/green)LED;Redwhenthebus
Aoperatesnormally;GreenwhenthebusB
operatesnormally;Amberwhenbothbuses
operate normally.
ERR indicator:Bi-color(red/green)LED;Redwiththein-
putabnormality;Greeninnormaloperating
conditions.
■SIDE DIP SW
• RTD Type: SW1, SW2
INPUT 1 (SW1) INPUT 2 (SW1)
RTDINPUT 3 (SW2) INPUT 4 (SW2)
12345678
OFF OFF OFF OFF OFF OFF OFF OFF Pt100(*)(JIS’97,IEC)
ON OFF OFF OFF ON OFF OFF OFF Pt100(JIS’89)
OFF ON OFF OFF OFF ON OFF OFF JPt100
OFF ON ON OFF OFF ON ON OFF Pt1000
• Burnout: SW3
SW3-1 BURNOUT
OFF Upscale(*)
ON Downscale
• Temperature Unit: SW3
SW3-2 SW3-3 TEMP. UNIT
OFF OFF °C(*)
ON OFF °F
• Conversion Rate: SW3
SW3-4 CONV. RATE
OFF 250msec.(*)
ON 1 sec.
(*)Factorysetting
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
1
3
2
5
7
6
11
13
12
15
17
16
*1. For dual redundant communication.
*2. To make use of shield line, connect to SLD and ground the terminal 20’s shield.
Note: Do not use void terminals.
SLD
SLD
SLD
SLD
SLD
SLD
*2
4
14
18
8
19
20
BUS CONNECTOR
INPUT 1
A
B
B
RTD
INPUT 2
A
B
B
RTD
INPUT 3
A
B
B
RTD
INPUT 4
A
B
B
RTD
INTERNAL POWER
BUS A
BUS B*1
• Unused Input Channels
Close across the unused input terminals with a resistor as
shownbelowandsettheDIPswitchforPt100input.
Unused channels left open are equal to the burnout, which
turnstheredERRLEDonandsetsaburnoutagatthe
PLC or the host device.
Unused channels can be specified and set so on the PC Con-
figurator Software (model: R3CON) without needing to con-
nect resistors at the field terminals.
1
2
INPUT 1
5
6
INPUT 2
11
12
INPUT 3
16
INPUT 4
100
3 7 13 17
15
R3S-RS4A
P. 3 / 3EM-8936
EXTERNAL DIMENSIONS unit: mm (inch)
1
20
130 (5.12)
27.5 (1.08) 109 (4.29)
120 (4.72)
POSITIONING
GUIDE
WIRING INSTRUCTIONS
■ APPLICABLE WIRE SIZE mm
• Solid: 0.2to1.0mm2(0.55to1.12dia.)
• Stranded:0.2to1.5mm2
(Tinning wire ends may cause contact failure and therefore
is not recommended.)
• Ferruled:
Unsheathed:0.25to1.5mm2
Sheathed:0.25to0.75mm2
•Exposewireconductorsby10mm(0.39”).
■CONNECTION PROCEDURE
Insert the wire end until it comes to a full stop while push-
ing slot with the tip of a screw driver as shown below. Be
sure wire insulation is not inside the terminal.
Screw Driver
Power wire
Stripped length
10mm
M-SYSTEM WARRANTY
M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such
product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System’s sole liability, and purchaser’s exclusive
remedies, under this warranty are, at M-System’s option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this
warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original
sales invoice.
THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR
SPECIAL DAMAGES OF ANY KIND WHATSOEVER.
M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: info@m-system.co.jp
PIN No. FUNCTION
1 INA1
2 INB1
3 INb1
4 SLD
5 INA2
6 INB2
7 INb2
8 SLD
9N
C
10 NC
11 INA3
12 INB3
13 INb3
14 SLD
15 INA4
16 INB4
17 INb4
18 SLD
19 SLD
20 SLD
INPUT PIN ASSIGNMENT
Autres manuels M-system Unité de contrôle
M-system
M-system R3-RS8 Manuel utilisateur
M-system
M-system R7HL-DC16B-R Manuel utilisateur
M-system
M-system R6N-RS2 Manuel utilisateur
M-system
M-system R7F4HD-DC32B Manuel utilisateur
M-system
M-system R7L-EC16B Manuel utilisateur
M-system
M-system R7E-DC16A Manuel utilisateur
M-system
M-system R7ML-EC16B Manuel utilisateur
M-system
M-system R7HL-DC16B Manuel utilisateur
M-system
M-system TR3EX Manuel utilisateur
M-system
M-system R8-NECT1 Manuel utilisateur
M-system
M-system R6S-RS2 Manuel utilisateur
M-system
M-system R7M-DC4G Manuel utilisateur
M-system
M-system R3-NMW1F Manuel utilisateur
M-system
M-system R3-NM4 Manuel utilisateur
M-system
M-system R3-NL1 Manuel utilisateur
M-system
M-system R7M-EC8C Manuel utilisateur
M-system
M-system R7C-EC8B/UL Manuel utilisateur
M-system
M-system R3-NF1 Manuel utilisateur
M-system
M-system R8-NC3 Manuel utilisateur
M-system
M-system R7ML-DC16B Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
