M-system R5-TS Manuel utilisateur

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-6112 Rev.3 P. 1 / 3

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Thermocouple input module (body + CJC sensors *1).......(1)

*1. Two provided for 2 channels input.

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■HOT INSERTION/REMOVAL OF MODULES

• Removing or replacing modules does not affect other mod-

ules on the same backplane. It is possible to replace them

without removing the power supply. However, replacing

multiple modules at once may greatly change line voltage

levels. We recommend that you replace them one by one.

■GENERAL PRECAUTIONS

• DO NOT set the switches while the power is supplied.

The switches are used only for maintenance without the

power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R5-BS).

THERMOCOUPLE INPUT MODULE MODEL R5-TS

R5-TS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-6112 Rev.3 P. 2 / 3

COMPONENT IDENTIFICATION

RUN LED

456

123

T/C Burnout

Temp. Unit

2345678

Function

Euro Type

Connector Terminals

RUN

■ SIDE VIEW ■FRONT VIEW

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

■SIDE DIP SW

(*) Factory setting

• Thermocouple Type: SW1, 2, 3, 4

SW T/C

1234

OFF OFF OFF OFF (PR)

ON OFF OFF OFF K (CA) (*)

OFF ON OFF OFF E (CRC)

ON ON OFF OFF J (IC)

OFF OFF ON OFF T (CC)

ON OFF ON OFF B (RH)

OFF ON ON OFF R

ON ON ON OFF S

OFF OFF OFF ON C (WRe 5-26)

ON OFF OFF ON N

OFF ON OFF ON U

ON ON OFF ON L

OFF OFF ON ON P (Platinel II)

• Temperature Unit: SW5, 6

SW TEMP. UNIT

5 6

OFF OFF °C (*)

ON OFF °F

OFF ON K (Absolute Temp)

• Burnout: SW7, 8

BURNOUT7 8

INPUT 1 INPUT 2

OFF OFF Downscale

ON ON Upscale (*)

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R5CON for detailed operation.

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Zero Scale -32000 to +32000 0

Full Scale -32000 to +32000 10000

Bias [Zero Adj.] -320.00 to +320.00 0.00

Gain [Span Adj.] -32000 to +32000 1.0000

Zero Base Depends on sensor type 0.00

Full Base Depends on sensor type 0.00

■CHANNEL BATCH SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Limit (V1.00 or higher) No check mark: Limits to the scaling values equivalent to -15 % to

+115 %.

Check-marked: Limits within Zero Scale to Full Scale.

No check mark

R5-TS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-6112 Rev.3 P. 3 / 3

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

456

123

6.5

(.26)

90 (3.54) LOCKING CLAMP

90 (3.54) 5.6

(.22)

18 (.71)

POSITIONING GUIDE

*Euro type connector terminals (4, 5 and 6) provided only with 2-ch. option.

CJC Sensor (model: CJM)

■CONNECTION DIAGRAM

INPUT 2

–

T / C

CJC

SENSOR

comp. wire

–

T / C

INPUT 1

CJC

SENSOR

–

BUS CONNECTOR

INTERNAL

POWER

INTERNAL

BUS A

INTERNAL

BUS B*

*For dual redundant communication.

Note: The section enclosed by broken line is with 2-ch. option.

WIRING INSTRUCTIONS

■EURO TYPE CONNECTOR TERMINAL

Applicable wire size: 0.2 to 2.5 mm2

Stripped length: 7 mm

Autres manuels M-system Unité de contrôle

M-system

M-system R8-SVT8 Manuel utilisateur

M-system

M-system R7M-DC4G Manuel utilisateur

M-system

M-system R7 Series Manuel utilisateur

M-system

M-system R7M-DAC16C Manuel utilisateur

M-system

M-system M6DXF1 Manuel utilisateur

M-system

M-system R7F4HD-DC32B Manuel utilisateur

M-system

M-system F2DL Manuel utilisateur

M-system

M-system R3-NC1 Manuel utilisateur

M-system

M-system M8CD1 Manuel utilisateur

M-system

M-system R7L-EC8A Manuel utilisateur

M-system

M-system R7ML-DC16B Manuel utilisateur

M-system

M-system R3-PA8 Manuel utilisateur

M-system

M-system R7M-RS4 Manuel utilisateur

M-system

M-system R7HL-DC16B-R Manuel utilisateur

M-system

M-system R3-SV8B Manuel utilisateur

M-system

M-system M8YC Manuel utilisateur

M-system

M-system MECHATROLINK R7K4FML3-6-DAC32B Manuel utilisateur

M-system

M-system R3Y-SS8N Manuel utilisateur

M-system

M-system R3-GC1 Manuel utilisateur

M-system

M-system R7D-EC16B Manuel utilisateur

M-system

M-system R7C-DC16B Manuel utilisateur

M-system

M-system R3-NC3 Manuel utilisateur

M-system

M-system R3-GM1 Manuel utilisateur

M-system

M-system R3Y-SV16 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur