M-system R3-SV8C Manuel utilisateur
R3-SV8C
P. 1 / 3EM-8423 Rev.2
DC VOLTAGE INPUT MODULE
(8 points, isolated, wide span voltage up to ±50V) MODEL R3-SV8C
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■ PACKAGE INCLUDES:
DC voltage input module ............................................. (1)
■ MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■ INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■ HOT INSERTION/REMOVAL OF MODULES
Removing or replacing modules does not affect other mod-
ules on the same backplane. It is possible to replace them
without removing the power supply. However, replacing
multiple modules at once may greatly change line voltage
levels. We recommend that you replace them one by one.
■ ENVIRONMENT
• Indoor use
• When heavy dust or metal particles are present in the air,
install the unit inside proper housing with sufficient ven-
tilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■ WIRING
• Do not install cables (power supply, input and output)
close to noise sources (relay drive cable, high frequency
line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■ UNUSED INPUT CHANNELS
Set the unused channels to -50 – +50V range. Otherwise, set
them as “Unused” with PC Configurator software: R3CON.
Unused channels left open with other settings may be equal
to the input lower than -15%, which sets a data abnormality
at the PLC or the host device.
■ AND ....
The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for sat-
isfying complete performance described in the data sheet.
INSTALLATION
Use the Installation Base (model: R3-BSx).
R3-SV8C
P. 2 / 3EM-8423 Rev.2
■ STATUS INDICATOR LED
RUN indicator: Bi-color (red/green) LED;
Red when the bus A operates normally;
Green when the bus B operates normally;
Amber when both buses operate normally.
ERR indicator: Bi-color (red/green) LED;
Red with the input circuit abnormality (AD
converter response failure);
Green in normal operating conditions.
■ SIDE DIP SW
• Input Range: SW1, SW2 (selectable per 4 channels)
INPUT 1 through INPUT 4 (SW1)
RANGEINPUT 5 through INPUT 8 (SW2)
1 2 3 4
OFF OFF OFF OFF -50 – +50V (*)
ON OFF OFF OFF -25 – +25V
OFF ON OFF OFF 0 – 50V
ON ON OFF OFF 0 – 25V
• Conversion Rate: SW3
SW CONVERSION RATE
160 ms (*)80 ms 40 ms 20 ms
SW3-1 OFF ON OFF ON
SW3-2 OFF OFF ON ON
(*)Factory setting
SW2SW1
ON
1
2
3
4
5
6
7
8
ON
ON
1
2
3
4
5
6
7
8
SW3
1
2
3
4
5
19
20
21
22
15
16
17
18
23
24
25
26
27
28
6
7
8
9
10
11
12
13
14
1
2
3
4
■ FRONT VIEW
ERR LED
RUN LED
■ SIDE VIEW
Range
Input 1-4 (SW1)
or
Input 5-8 (SW2)
Conv.
Rate
Functions
COMPONENT IDENTIFICATION
R3-SV8C
P. 3 / 3EM-8423 Rev.2
WIRING INSTRUCTIONS
■ SOLDERLESS TERMINAL mm (inch)
Refer to the drawing below for recommended ring tongue
terminal size. Spade tongue type is also applicable. Solder-
less terminals with insulation sleeve do not fit. Applicable
wire size: 0.3 – 0.5 mm2
3.2 (.13) dia.
4 min.
(.16)
12 (.47) max.
6 max.
(.24)
3 (.12) max.
TERMINAL
COVER
5
19
20
21
22
15
16
17
18
23
24
25
26
27
28
6
7
8
9
10
11
12
13
14
1
2
3
4
130 (5.12)
27.5 (1.08) 109 (4.29) POSITIONING
GUIDE
28–M3
SCREW
6.2
(.24)
INTERNAL POWER
BUS A
BUS B*
*For dual redundant communication.
DO NOT connect external wiring to the unused terminals.
BUS CONNECTOR
1
3
–
INPUT 1
+
4
6
–
INPUT 2
+
7
9
–
INPUT 3
+
10
12
–
INPUT 4
+
15
17
–
INPUT 5
+
18
20
–
INPUT 6
+
21
23
–
INPUT 7
+
24
26
–
INPUT 8
+
■ DIMENSIONS mm (inch)
■ CONNECTION DIAGRAM
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
M-SYSTEM WARRANTY
M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such
product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System’s sole liability, and purchaser’s exclusive
remedies, under this warranty are, at M-System’s option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this
warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original
sales invoice.
THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR
SPECIAL DAMAGES OF ANY KIND WHATSOEVER.
M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]
Autres manuels M-system Unité de contrôle
M-system
M-system R3-SV8B Manuel utilisateur
M-system
M-system R5T-DA4 Manuel utilisateur
M-system
M-system R3-RR8 Manuel utilisateur
M-system
M-system R3-NP1 Manuel utilisateur
M-system
M-system R3-NC2 Manuel utilisateur
M-system
M-system TR3EX Manuel utilisateur
M-system
M-system R7ML-YV2 Manuel utilisateur
M-system
M-system R3-PD16A Manuel utilisateur
M-system
M-system R3-PA4 Manuel utilisateur
M-system
M-system R3-AR4 Manuel utilisateur
M-system
M-system R7HL-DC16A Manuel utilisateur
M-system
M-system R7ML-EC8B Manuel utilisateur
M-system
M-system R7M-MS4 Manuel utilisateur
M-system
M-system R7C-YS2 Manuel utilisateur
M-system
M-system R30YS4 Manuel utilisateur
M-system
M-system R7ML-EC16B Manuel utilisateur
M-system
M-system R7F4DD-DC16A-H Manuel utilisateur
M-system
M-system LONWORKS R3-NL2 Manuel utilisateur
M-system
M-system R3-GD1 Manuel utilisateur
M-system
M-system R6D-TS2 Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
