Lutron Electronics GRAFIK Eye QSGRJ-3P Mode d'emploi

LUTRON

Installation and

Operation Guide

Please Read

The GRAFIK Eye QS control unit allows

for control of both lights and shades,

without interfaces, using a single control

unit. Features include pushbutton scene

recall, info screen that displays energy

savings and status, IR receiver, astronomic

timeclock, contact closure input, and

engravable backlit buttons that are easy to

find and operate.

Model Numbers: QSGRJ-3P, QSGRJ-4P, QSGRJ-6P

QSGR-3P, QSGR-4P, QSGR-6P

120 V 50/60 Hz 220 - 240 V 50/60 Hz

Unit Capacity (watts) 2000 W 3000 W

MLV 2000 VA / 1 600 W 3000 VA / 2 400 W

Zone Capacity (watts) 25 – 800 W 40 – 1200 W

MLV 25 – 800 VA / 25 – 600 W 40 – 1200 VA / 40 – 960 W

See page 8 for PELV (Class 2: USA) ratings.

®GRAFIK Eye® QS Installation and Operation Guide 2

Contents

Features and Functions of the

GRAFIK Eye® QS...............................3

Wiring the GRAFIK Eye® QS

Overview of Line Voltage/Mains Wiring . . . . . . . . . 4

Line Voltage Wiring Details. . . . . . . . . . . . . . . . . . . 5

Overview of PELV (Class 2: USA) Wiring . . . . . . . . 7

QS Link Control Wiring Details. . . . . . . . . . . . . . . . 8

QS Link Control Wiring

and Terminal Connection Example . . . . . . . . . . . 9

Powering More Than 3 Wallstations . . . . . . . . . . 10

Completing Installation of the

GRAFIK Eye® QS.......................11

General Functionality . . . . . . . . . . . . . . . . . . . 12

Pre-Programmed Button Functionality . . . . . 13

Zone Button Operation

Zone LED Displays for % of Lighting Levels . . . . 14

Programming Mode

Entering and Exiting Programming Mode . . . . . . 15

Navigating Menus in Programming Mode . . . . . . 15

Wireless Mode.........................16

FCC Information ..........................16

Zone Setup

Assign Load Types ........................17

Assign Non-Dim Load Type . . . . . . . . . . . . . . . . . 17

Setting Load Types........................18

Set High End or Low End Trim. . . . . . . . . . . . . . . 19

Set Minimum Level (optional) . . . . . . . . . . . . . . . . 19

Label a Zone (optional) . . . . . . . . . . . . . . . . . . . . . 20

Contact Closure Input (CCI) Mode Setup . . . 21

Associating Wireless Occupancy Sensors

and GRAFIK Eye® QS Wireless

Control Units.........................22

Occupancy Sensor Setup

Mode Assignment.........................23

Scene Mode .............................24

Zone Mode ..............................25

Label an Occupancy Sensor (optional) . . . . . . . . 26

Configure Occupancy Sensor Settings . . . . . . . . 27

Associating Wireless Daylight Sensors

and GRAFIK Eye® QS Wireless

Control Units.........................28

Daylight Sensor Setup

Assign Sensors ...........................29

Label a Daylight Sensor (optional) . . . . . . . . . . . . 30

Scene Setup

Set Zone Levels, Fade Rates,

and Shade Group Actions . . . . . . . . . . . . . . . . . 31

Label a Scene (optional) . . . . . . . . . . . . . . . . . . . . 32

Enable/Disable Daylighting per Scene. . . . . . . . . 32

Set Save Mode

Save Modes..............................33

Quick Scene Programming

Save by OK Mode.........................34

Timeclock Operation

Set Time and Date ........................35

Set Location .............................36

Set Daylight Saving Time . . . . . . . . . . . . . . . . . . . 36

Add an Event.............................37

Delete an Event...........................38

View an Event ............................38

Set a Holiday.............................39

View a Holiday............................39

Delete a Holiday ..........................39

Copy a Schedule..........................40

Delete a Schedule.........................40

Afterhours Mode..........................41

Set Up Afterhours Mode . . . . . . . . . . . . . . . . . . . . 42

End Afterhours Mode . . . . . . . . . . . . . . . . . . . . . . 42

Associating Pico® Wireless Controls and

GRAFIK Eye® QS Wireless Control Units

To use the Pico Wireless Control as a

Scene Controller.........................43

To use the Pico Wireless Control as a

Zone Controller..........................44

Associating Sivoia® QS Shades/Drapes

and GRAFIK Eye® QS Control Units . . . . . . 45

Adjusting Shade Settings

Setting Limits.............................46

Preset Adjustment: Simple Method . . . . . . . . . . . 47

Preset Adjustment: Advanced Method . . . . . . . . 47

Name a Group of Shades . . . . . . . . . . . . . . . . . . . 48

Associating Multiple GRAFIK Eye® QS

Control Units.........................49

Diagnostics and Special Settings

Enable/Disable Timeclock . . . . . . . . . . . . . . . . . . 50

Enable/Disable IR Receiver . . . . . . . . . . . . . . . . . 50

Enable/Disable Backlighting. . . . . . . . . . . . . . . . . 50

Diagnostics ..............................50

Activate System Accessories . . . . . . . . . . . . . 51

Faceplate Removal . . . . . . . . . . . . . . . . . . . . . 51

Language Selection . . . . . . . . . . . . . . . . . . . . 51

Troubleshooting .......................52

Troubleshooting: Wireless Functions. . . . . . . 53

Troubleshooting: Shade Functions . . . . . . . . 54

Warranty .............................55

Contact Information . . . . . . . . . . . . . . . . . . . . 55

1 2 3 4 5 6

®GRAFIK Eye® QS Installation and Operation Guide 3

Info screen

Displays status or

programming functions

Scene buttons

With integral scene

indicator LEDs

Optional Shade

button groups

Preset and raise/lower

buttons with integral LEDs

(maximum of 3 button

groups)

Zone numbers

Zone raise/lower buttons

Zone LEDs display current

lighting zone levels

Timeclock button

Displays current

timeclock info

OK button

Used for programming,

fade time

Infrared receiver

For handheld remote use

Master buttons

Temporarily raise and lower

lighting levels on unit

USB type mini B

For programming via PC

{

Hinged faceplate

Features and Functions of the GRAFIK Eye® QS

®GRAFIK Eye® QS Installation and Operation Guide 4

1234

1 2 ABC

123456LN

Wiring the GRAFIK Eye® QS:

Overview of Line Voltage/Mains Wiring

12 AWG (4.0 mm2)

each terminal

120 - 127 V

220 - 240 V

Distribution

Panel

Line Voltage/Mains

Cables and Load Wiring

123456LN

Incandescent load

Load controlled

by power module

Terminal labels:

L: Hot/Live

N: Neutral

: Ground

1-6: Dimmed/Switched

line voltage outputs

Power module

®GRAFIK Eye® QS Installation and Operation Guide 5

Wiring the GRAFIK Eye® QS: Line Voltage Wiring Details

• Use properly certified cable for all line

voltage/mains cables.

• Proper short-circuit and overload

protection must be provided at the

distribution panel. You can use up to a

20 A circuit breaker for your installation.

• Install in accordance with all local and

national electrical codes.

• PELV (Class 2: USA) terminals may be

temporarily unplugged for ease of IR,

occupancy sensor, and control wiring.

• Notice: Risk of damage to unit. Do not

connect line voltage/mains cable to PELV

(Class 2: USA) terminals.

Step 1: Install wallbox. Mount a 3½-in

(89 mm) deep 4-gang U.S. wallbox on a

dry, flat indoor surface that is accessible

and allows for system programming and

operation. Allow at least 4½ in (110 mm)

clearance above and below the faceplate

to ensure proper heat dissipation. Allow

1 in (25 mm) for faceplate overhang on

all sides.

Note: 4-gang wallbox available from

Lutron; P/N 241400.

Step 2: Test load wiring.

• Turn power OFF at the circuit breaker or

fuse box.

• Connect a standard light switch between

the live lead and load wire to test the

circuit.

• Turn power ON and check for short or

open circuits. If load does not operate,

the circuit is open. If the circuit breaker

trips (fuse blows or opens), a load short

may exist. Correct short or open circuits

and test again.

Step 3: Check control unit wiring.

• Earth/ground terminal connection must

be made as shown in wiring diagrams

(see page 4).

• Do not mix different load types on the

same zone.

• Follow all local and national electrical

codes when installing PELV (Class 2:

USA) wiring with line voltage/mains

wiring.

WARNING! Shock hazard. May

result in serious injury or death.

Always turn off circuit breaker or

remove main fuse from power line

before doing any work. Before

connecting the loads to the

GRAFIK Eye QS control unit, test

the loads for short-circuits.

Neutral

Hot/Live Switch

Load

LUTRON

Faceplate overhangs

wallbox on all sides;

allow 1 in (25 mm)

4.5 in

(110 mm)

®GRAFIK Eye® QS Installation and Operation Guide 6

Wiring the GRAFIK Eye® QS: Line Voltage Wiring Details (continued)

Step 4: Connect line voltage and loads

to control unit.

• Strip 5/16 inch (8 mm) of insulation off the

line voltage/mains cables in the wallbox.

• Connect the line voltage/mains, ground,

and load wires to the appropriate

terminals on the back of the control unit.

L: Hot/Live

N: Neutral

: Ground

Terminals 1-6: Dimmed/Switched

line voltage outputs

5/16 inch

(8 mm)

The recommended installation torque is

5.0 in∙lbs (0.6 N∙m) for line voltage/mains

connections and 5.0 in∙lbs (0.6 N∙m) for

the earth/ground connection.

Note: See page 18 for a list of

compatible load types and instructions

for programming the GRAFIK Eye QS to

properly recognize them.

Notice: Risk of damage to unit. GRAFIK Eye QS control units must be in stalled by a

qual i fied electrician in accordance with all applica ble reg u la tions and building codes.

Im prop er wiring can result in dam age to control units or oth er equipment.

Note: To avoid over heat ing and pos si ble damage to equipment, do not install control

units to dim re cep ta cles, mo tor-op erated ap pli ances, or flu o res cent lighting not

equipped with Lutron Hi-lume®, Eco-10®, or Tu-Wire® electronic dim ming ballasts, or

other devices approved for your location. In dimmed magnet ic low-voltage cir cuits, you

can pre vent trans former overheating and failure by avoid ing excessively high current

flow. Do not op erate control units with any lamps re moved or burned out; re place

any burned out lamps immediate ly; use only transform ers that in cor po rate ther mal

pro tection or fused pri ma ry wind ings. Control units are de signed for res i den tial and

commercial use, for indoor use only.

1234

1 2 ABC

123456LN

Contact Closure Input Wiring

For settings, see page 21.

®GRAFIK Eye® QS Installation and Operation Guide 7

1 2 ABC

NH123456

1234

1 2

ABC

123456LN

1234

1 2

ABC

123456LN

Note: Use appropriate wire connecting devices

as specified by local codes.

Example:

Occupancy sensor

(maximum 1)

1: COM

2: 24 V *

3: MUX

4: MUX

Control Wiring

Wiring the GRAFIK Eye® QS:

Overview of PELV (Class 2: USA) Wiring

IR Wiring

From external

IR connection

(by others)

18 AWG (1.0 mm2)

each terminal

18 AWG

(1.0 mm2)

each

terminal

1: IR DATA

2: IR COM

A: CCI SIG

B: 24 V

C: CCI COM

To control stations,

shades, or other

GRAFIK Eye QS

control units

Data (terminals 3 and 4):

Twisted, shielded pair 22 AWG (0.5 mm2)

each terminal

Common and power (terminals 1 and 2):

Two 18 AWG (1.0 mm2) each terminal

* Do not connect terminal 2

between any GRAFIK Eye QS and

any other power supply, including

another GRAFIK Eye QS.

See page 9 for detailed wiring

example.

1234

1 2

ABC

123456LN

Example:

Emergency lighting interface (maximum 1)

Note: The GRAFIK Eye QS control unit

must be powered by a Normal/Emergency

distribution panel for proper ELI operation.

Refer to the LUT-ELI-3PH Installation Guide

for the complete wiring diagram.

A: CCI SIG

B: 24 V

C: CCI COM

LUT-ELI-3PH

Signal

+V Input

Circuit Common

• System communication uses PELV (Class 2: USA)

wiring.

• Follow all local and national electrical codes when

installing PELV (Class 2: USA) wiring with line

voltage/mains wiring.

• Each terminal accepts up to two 18 AWG (1.0 mm2)

wires.

• Total length of control link must not exceed

2 000 feet (610 m).

• Make all connections in the control unit’s wallbox.

• Wiring can be T-tapped or daisy-chained.

• Wire sizes:

- Two 18 AWG (1.0 mm2) conductors for control

power.

- One twisted, shielded pair of 22 AWG (0.5 mm2) for

data link.

- Cable is available from Lutron:

GRX-CBL-346S-500 (non-plenum) and

GRX-PCBL-346S-500 (plenum). Check

compatibility in your area.

• PELV (Class 2: USA) 24 V 150 mA.

®GRAFIK Eye® QS Installation and Operation Guide 8

QS smart

power

panel

LUTRON

LUTRONLUTRON

LUTRON

T-Tap Wiring Example

GRAFIK Eye QS

Sivoia QS

seeTouch QS

Wiring the GRAFIK Eye® QS:

QS Link Control Wiring Details

System Limits

The QS wired communication link is limited to 100 devices or 100 zones. Please

note the zone count and power draw unit information in the following table.

QS Device Zone

Count

Power Draw Units

(supplied)

Power Draw

Units (consumed)

3-zone GRAFIK Eye QS 3 3 0

4-zone GRAFIK Eye QS 4 3 0

6-zone GRAFIK Eye QS 6 3 0

8-zone GRAFIK Eye QS 8 3 0

16-zone GRAFIK Eye QS 16 3 0

seeTouch® QS 0 0 1

International seeTouch®

0 0 1

Sivoia® QS 1 0 (Refer to Spec.

Submittal)

Contact closure interface 5 0 3

Network interface 0 0 2

DMX interface 0 0 2

QS smart power panel 0 (Refer to Spec.

Submittal)

QS link power supply 0 8 0

LUTRON

LUTRONLUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

LUTRONLUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

LUTRONLUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

5.26

4.263.75

2.50

1.06

5.26

4.263.75

2.50

1.06

LUTRON

LUTRONLUTRON

LUTRON

GRAFIK Eye QS Sivoia

seeTouch QS

Daisy-Chain Wiring Example

QS smart

power panel

GRAFIK Eye QS

LUTRON

LUTRONLUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

5.26

4.263.75

2.50

1.06

LUTRON

LUTRONLUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

LUTRONLUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

Wiring the GRAFIK Eye® QS:

QS Link Control Wiring and Terminal Connection Example

®GRAFIK Eye® QS Installation and Operation Guide 9

1234

1 2 ABC

123456HN

1234

1 2 ABC

123456HN

1234

1 2 ABC

123456HN

1234

1 2 ABC

123456HN

QS1 powers wallstation 1

only; terminal 2 terminates at

wallstation 1

QS2 and

QS3 have

their own

power

supply; no

terminal 2

connection

QS3 powers

wallstations 2, 3,

and 4; no terminal 2

connection between

wallstations 4 and 5

QS4 powers wallstations 5, 6, and

7 only; no terminal 2 connection

between wallstations 4 and 5

Power

panel

powers

this shade

only

Sivoia QS

shade

Sivoia QS

smart power

supply panel

Control units shown in rear view

• Connect the terminal 1, 3, and 4

connections to all control units,

wallstations, and control interfaces.

• Each control unit has its own power

supply. Terminate the terminal 2

connection (24 V power) so that each

control unit supplies power to a maximum

of three wallstations. Do not connect

terminal 2 between a GRAFIK Eye QS

control unit and any other GRAFIK Eye

QS control unit and/or another power

supply.

• Each wallstation should receive power

from only one control unit.

QS3

QS1

QS2 QS4

®GRAFIK Eye® QS Installation and Operation Guide 10

1 2 3 4

1 2 ABC

123456LN

Wiring the GRAFIK Eye® QS:

Powering More Than 3 Wallstations

• The +24 VDC wire from the power supply

connects to QS link terminal 2 on all of

the wallstations it is powering. This wire

does not connect to terminal 2 on the

GRAFIK Eye QS.

• The GRAFIK Eye QS can power up to

3 seeTouch® wallstations. An external

24 V power supply is required to power

more than three wallstations.

To power source

QSPS-P1-1-50

(powers up to 8 seeTouch QS

wallstations)

• The Common wire from the power supply

connects to QS link terminal 1 on all

of the wallstations it is powering and

terminal 1 on the GRAFIK Eye QS.

• The communication signals on the QS

link (terminals 3 and 4) connect from

the wallstations to the GRAFIK Eye QS

on twisted, shielded cable just as when

an additional power supply is not being

used. Control unit shown in rear view.

GRAFIK Eye QS

control unit (rear view)

1 twisted pair

22 AWG

(0.5 mm2)

Lutron cable

GRX-CBL-346S-500 (non-plenum) or

GRX-PCBL-346S-500 (plenum)

seeTouch QS wallstations

(1) 18 AWG

(1.0 mm2)

Common

Autres manuels pour GRAFIK Eye QSGRJ-3P

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Lutron Electronics Unité de contrôle

Lutron Electronics

Lutron Electronics Vive Series Manuel utilisateur

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRN-6PCE Mode d'emploi

Lutron Electronics

Lutron Electronics Grafik Eye GRX-4000 Series Instructions de montage

Lutron Electronics

Lutron Electronics QS Timeclock Manuel du propriétaire

Lutron Electronics

Lutron Electronics GFS-5E Manuel utilisateur

Lutron Electronics

Lutron Electronics PPS-9312 Manuel utilisateur

Lutron Electronics

Lutron Electronics PowPak RMJS-CCO1-24-B Manuel utilisateur

Lutron Electronics

Lutron Electronics AuroRA ARMC-5T Manuel d'utilisation et d'entretien

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRJ-8E Instructions d'installation et d'utilisation

Lutron Electronics

Lutron Electronics QSGRK-6D Manuel du propriétaire

Lutron Electronics

Lutron Electronics TriPak Series Manuel utilisateur

Lutron Electronics

Lutron Electronics Vive PowPak Manuel utilisateur

Lutron Electronics

Lutron Electronics Vive DFCSJ-OEM-OCC Manuel utilisateur

Lutron Electronics

Lutron Electronics seeTouch guestroom solutions Manuel utilisateur

Lutron Electronics

Lutron Electronics QSGRK-3PCE Manuel du propriétaire

Lutron Electronics

Lutron Electronics GRAFIK Eye Architrave GRX-4SLB-DW Manuel utilisateur

Lutron Electronics

Lutron Electronics Grafik Eye GRX-4000 Series Manuel utilisateur

Lutron Electronics

Lutron Electronics LMM-16R-DV-B Manuel utilisateur

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-3PD-1 Manuel utilisateur

Lutron Electronics

Lutron Electronics GRAFIK 6000 Manuel utilisateur

Lutron Electronics

Lutron Electronics Maestro Wireless Pico Series Manuel utilisateur

Lutron Electronics

Lutron Electronics Energi Savr Node Manuel utilisateur

Lutron Electronics

Lutron Electronics GRAFIK Eye QS Manuel du propriétaire

Lutron Electronics

Lutron Electronics PowPak Energi TriPak Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur