Lutron Electronics LQR-WPM-6D Mode d'emploi

LUTRON

Wallbox Power Module with DALI Control Unit

Installation and Operation Guide

Please Read

The Wallbox Power Module controls six

to sixteen zones of DALI compliant output

devices.

The Wallbox Power Module can control

up to 64 DALI compliant output devices

(devices must comply with IEC/EN 60929

ed. 3.0 2006-01) which can be addressed

and grouped into zones.

The Power Module can be configured for

wired, QS link (HomeWorksRQS only), or

wireless, RF link (HomeWorksRQS and

RadioRAR2), communication.

English Español Italiano

Français Deutsch

Model Numbers:

Ratings: 120–240 V~50/60 Hz 100 mA

230 V~50/60 Hz 100 mA

Typical Power Consumption*: 7 W (24 BTUs)

Power Draw Units (PDUs)**: 0

Output: DALI Link: 18 V 250 mA

Codes: Install in accordance with all applicable electrical codes.

Environment: Ambient operating temperature: 0 °C to 40 °C, 0% to 90%

humidity, non-condensing. Indoor use only.

LQR-WPM-6D LQR-WPM-8D LQR-WPM-16D

LQRK-WPM-6D LQRK-WPM-8D LQRK-WPM-16D

LQRM-WPM-6D LQRM-WPM-8D LQRM-WPM-16D

LQRN-WPM-6D LQRN-WPM-8D LQRN-WPM-16D

LQRQ-WPM-6D LQRQ-WPM-8D LQRQ-WPM-16D

NederlandsPortuguês

*Typical Power Consumption test conditions: all loads

off, button LED on.

**For more information about Power Draw Units

(PDUs), please see the HomeWorks®QS Wiring and

Power Guidelines document on the HomeWorks®QS

Resource Website

中文

®Wallbox Power Module Installation and Operation Guide 2

D1 D1 D2 D2

DALI-Compliant Bus Wiring

(See the bus wiring details section for

complete specification)

Note: DALI-compliant bus link wires are

not polarity sensitive. Labels D1 and D2

are for illustration purposes only.

• Pull power wiring from distribution

panel and to light fixtures

• Each line voltage terminal can accept

one 4.0 mm2wire

• Consult Lutron for non-dim relay wiring

and/or load side emergency transfer

wiring

D1 D1 D2 D2

123456LN

Wiring the Wallbox Power Module with DALI Control Unit:

Overview of Line Voltage/Mains and DALI-Compliant Bus Wiring

Distribution

Panel

Rear of

WPM control

unit

120 V~or

220–240 V~only

Not used

4.0 mm2each

terminal

Line Voltage/Mains

Cables and

Load Wiring

To additional

DALI-compliant loads

D1 D1 D2 D2

DALI-compliant

loads

Terminal labels:

L: Hot/Live

N: Neutral

: Ground

Wiring the Wallbox Power Module with DALI Control Unit:

Line/Mains Voltage Wiring Details

Wallbox Power Module Installation and Operation Guide 3

• Use properly certified cable for all line

voltage/mains cables.

• Proper short-circuit and overload

protection must be provided at the

distribution panel.

• Install in accordance with all local and

national electrical codes.

• IEC PELV terminals may be temporarily

unplugged for ease of IR, occupancy

sensor, and control wiring.

• Notice: Risk of damage to unit. Do not

connect line voltage/mains cable to IEC

PELV terminals.

Step 1: Install wallbox. Mount an

89 mm deep 4-gang U.S. wallbox on a

dry, flat indoor surface that is accessible

and allows for system programming

and operation. Allow at least 110 mm

clearance above and below the faceplate

to ensure proper heat dissipation.

Allow 25 mm for faceplate overhang on

all sides.

Note: 4-gang wallbox available from

Lutron; P/N 241400.

Step 2: Check control unit wiring.

•Earth/ground terminal connection must

be made as shown in line voltage wiring

diagrams.

• Follow all local and national electrical

codes when installing IEC PELV wiring

with line voltage/mains wiring.

• Use the rearmost knockouts when pulling

wires into the wallbox. This will provide

the most clearance when mounting the

module.

WARNING! Shock hazard. May

result in serious injury or death.

Always turn off circuit breaker or

remove main fuse from power line

before doing any work.

Step 3: Connect line voltage and loads

to control unit.

• Strip 8 mm of insulation off the line

voltage/mains cables in the wallbox.

• Connect the line voltage/mains, ground,

and load wires to the appropriate

terminals on the back of the control unit.

L: Line/Hot

N: Neutral

: Ground

The recommended installation torque is

0.6 N•m for line voltage/mains

connections and 0.6 N•m for the earth/

ground connection.

Notice: Proper short circuit and overload

protection must be provided at the

distribution panel. You can use up to

a 20 A maximum circuit breaker with

adequate short-circuit breaking capacity

for your installation.

Notice: Risk of damage to unit.

The Wallbox Power Module with DALI

control units must be installed by a

qualified electrician in accordance with

all applicable regulations and building

codes. Improper wiring can result

in damage to control units or other

equipment.

Notice: To avoid overheating and

possible damage to equipment, do not

install control units to dim receptacles,

motor-operated appliances, or

fluorescent lighting not equipped with

DALI electronic dimming ballasts, or other

DALI devices approved for your location.

Control units are designed for residential

and commercial use, for indoor use only.

8 mm

LUTRON

Faceplate overhangs

wallbox on all sides;

allow 25 mm

110 mm

OFF

®Wallbox Power Module Installation and Operation Guide 4

• DALI terminal block is double insulated

from QS and mains voltage terminals.

• DALI bus wiring may be run in the same

conduit as mains wiring.

• Lutron recommends using two different

colors for D1 and D2 (DALI bus) wires.

This will prevent wiring mistakes in

junction boxes where several different

DALI bus wires combine. Use the

following instructions for wiring the DALI

bus.

• Each DALI bus link can have only 1

Wallbox Power Module (WPM) with DALI

control unit connected to it. No additional

DALI supplies can be on the link.

• Up to 64 DALI devices can be connected

to the DALI bus.

• No other devices may be connected to

the DALI link.

WARNING! Shock hazard.

May result in serious injury or

death. Do not wire live. Always

turn off circuit breaker or remove

main fuse from power line before

wiring and servicing the Wallbox

Power Module.

Step 1: Use the wire size chart at right to

determine which wire size to use based

on the length of the DALI bus.

Step 2: Wire the DALI bus from terminal

D1 and terminal D2 to all DALI devices.

Step 3: Turn on circuit breaker to

energize.

DALI Bus

18 V-250 mA

Wiring the Wallbox Power Module with DALI Control Unit:

DALI-Compliant Bus Wiring Details

Wiring Size and Bus Length

DALI bus wires D1 and D2 are not

polarity sensitive. DALI bus length is

limited by the wire gauge used for D1 and

D2 as follows:

Wire Gauge Maximum DALI

Bus Length

1.5 mm2300 m

0.75 mm2150 m

0.50 mm2100 m

Note: Some DALI devices (ballasts,

drivers, and interfaces) accept

connections to daylight sensors

and occupancy sensors. For

instructions on installing and

operating these devices, refer to

their individual instruction sheets.

OFF

®Wallbox Power Module Installation and Operation Guide 5

Wiring the Wallbox Power Module with DALI Control Unit:

IEC PELV/NECRClass 2 Wiring Details (HomeWorksRQS only)

The WPM can be configured for wired/QS

link (HomeWorksRQS only) or wireless/

RF link (RadioRAR2 and HomeWorksR

QS) communication. The following

diagram illustrates wiring the device to

a QS link. HomeWorksRQS supports

selection of wired or RF communications.

A Wallbox Power Module main unit that

communicates back to a HomeWorksR

QS processor through the RF link should

not have any QS wired link connections.

In RadioRAR2 only RF communication is

available

WARNING! Shock hazard. May

result in serious injury or death.

Always turn off circuit breaker or

remove main fuse from power line

before doing any work.

Step 1: Strip 25 mm of insulation from

the IEC PELV/NECRClass 2 cable.

Step 2: Strip 7 mm of insulation from

each wire in the cable.

Step 3: Connect the wires to the QS Link

terminal block, making sure no bare wire

is exposed after making the connections.

The recommended installation torque is

0.4 N•m for QS Link connections.

OFF

Note: The QS Link IEC PELV/NECR

Class 2 cable and terminal block should be

separated from the DALI Link wires.

D1 D1 D2 D2

Data link: twisted, shielded pair

0.34 mm2 to 0.75 mm2

DO NOT CONNECT PIN 2

IEC PELV /NECRClass 2 control

wiring: 0.75 mm2

HomeWorksRQS Link 610 m

maximum total wire length

per run

Pin 2 does not get connected to the

WPM – it does not require link power

To additional QS devices

D1 D1 D2 D2

Note: The QS Link IEC PELV/NECR

Class 2 cable and terminal block should

be separated from the line voltage/mains

cables by at least 6 mm.

®Wallbox Power Module Installation and Operation Guide 6

Completing Installation of the Wallbox Power Module with DALI Control Unit:

Step 1: Grasp the top corners of the

wallplate and pull forward to detach it

from the wallbox power module.

Step 2: Use the screws provided to

mount to the wallbox.

Note: When mounted in the wallbox, the

QS Link cable and terminal block should

remain separated from the line voltage/

mains cables.

Step 3: To snap the wallplate on, rest

the top of the wallplate in the grooves at

the top of the unit and press firmly at the

bottom corners to secure.

Step 4: Turn on circuit breaker and check

that it does not trip. For any feed circuit

that trips, locate the short or resolve the

wiring problem before proceeding.

Step 5: Use Default Scene Button:

To test the lights or control the lights

when the WPM is not connected or

communicating with the system, use the

default scene button. The LED will toggle

on/off following the local press on/off of

the default scene button.

Wallbox

Wallbox Power

Module

Wallplate

Mounting Screws

LUTRON

Status LED Default Scene Button

OFF

®Wallbox Power Module Installation and Operation Guide 7

Entering and Exiting Programming Mode

Entering programming mode:

Press and hold the timeclock (back) and OK

buttons simultaneously for 3 seconds. The

LED in the scene button and corresponding

LEDs below the scene button will scroll

from top to bottom, confirming that you are

in programming mode, and the info screen

will display the main menu.

Exiting programming mode:

Press and hold the timeclock (back) and OK

buttons simultaneously for 3 seconds. The

info screen will go to Scene 1.

Navigating Menus in Programming Mode

Master Buttons

The Master buttons allow you to move through the menu

choices. The current choice is highlighted on the info screen.

OK Button

The “OK” button chooses the current highlighted menu choice.

This will either take you to the next menu or accept a setting you

have selected. When the screen displays a Yes/No question, the

“OK” button is “Yes”.

Timeclock Button

The Timeclock button functions as a “back” button during

programming mode. Pressing the Timeclock button takes

you back one step in the current menu. Pressing it repeatedly

will eventually return you to the main menu, but will not exit

programming mode. When the screen displays a Yes/No

question, the Timeclock button is “No”.

Programming Mode

12345691011 12 13 14 7815

9-16

1-8

Master buttons

“OK” button

Timeclock (back) button

Main menu

Scene setup

Timeclock

Scene 1

Fade time

3 seconds

Wallbox Power Module Installation and Operation Guide 8

DALI Setup

After DALI devices are wired and powered, they must be addressed before the

system can control them. The “Build System” command automates this process.

Note: All existing DALI programming will be deleted when the “Build System”

command is run, including DALI sensor programming on the Wallbox Power

Module control unit.

Building the System

1. Enter programming mode by pressing and holding the OK

button and timeclock (back) button for 3 seconds.

2. Use the Master buttons to highlight “

DALI

” and press the OK

button to accept.

3. Use the Master buttons to highlight “Build system” and press

the OK button to accept.

4. Press the OK button to erase all current programming, reset

and address DALI devices, and find sensors on the system.

5. Exit programming mode.

Note: After running “Build System”, Zone 4 will control all DALI

devices for diagnostics and verification of wiring. (This

feature is disabled once any of the addressed devices

are assigned to a zone on the Wallbox Power Module

control unit.) Use the Zone 4 raise/lower buttons to verify

that all devices are correctly addressed. If a device does

not respond, repeat the “Build System” command and/

or check the wiring.

Main menu

Zone setup

DALI

Assign zones

Build system

Erase digital load

Programming?

Build system

DALI

12345691011 12 13

14 7815 16

9-16

1-8

Use Zone 4

raise/lower

buttons

to verify

all DALI

devices

have been

addressed.

Searching...

Found

x Loads

Found

12345691011 12 13 14 7

9-16

1-8

Master

buttons

button

Timeclock

(back) button

®Wallbox Power Module Installation and Operation Guide 9

12345691011 12 13 14 7

9-16

1-8

12345691011 12 13

14 7815 16

9-16

1-8

DALI Setup

Assigning/Unassigning a DALI Device to a Zone

DALI devices must be addressed on the system (see previous page) before assigning

or unassigning to a zone.

1. Enter programming mode.

2. Use the Master buttons to highlight “DALI” and press the OK

button to accept.

3. Use the Master buttons to highlight “Assign zones” and press

the OK button to accept.

4. Use the Master buttons to scroll through the DALI devices on

the link. The selected device will flash, and the info screen

will display the device number and the number of devices on

the link. If the device is currently assigned to a zone, the zone

number will display at the bottom of the screen and the LEDs

for the zone will go on; otherwise, the info screen will display

“*Unassigned*”.

• Press the zone raise button to assign the device to that

zone.

• Press the zone lower button to unassign the device to that

zone.

5. Press the Timeclock (back) button to return to the DALI menu.

DALI devices will return to normal levels.

6. Exit programming mode.

Notes

•Devices that were previously assigned to a zone will be

removed from the old zone and assigned to the new zone

(each device can be assigned to only 1 zone at a time).

• Devices can be assigned only to zones set to DALI load type.

•Refer to the Zone Setup section for instructions on changing

load type.

Use the

zone raise

or lower

button to

assign or

unassign a

DALI device

to that

zone.

Zone LEDs

Main menu

Zone setup

DALI

Address All

Assign zones

Ballast 2 / 23

Zone 3

DALI

Assign zones

Ballast 2 / 23

*Unassigned*

Master

buttons

button

Timeclock

(back) button

Wallbox Power Module Installation and Operation Guide 10

DALI Setup

Addressing DALI Devices

The “Address All” command can be used to add/replace DALI devices on the system

without running the “Build System” command (this avoids erasing all the existing

programming information).

The “Address All” command will treat replacement DALI devices as completely new

devices added to the system, increasing the total device count with every new/

replacement device.

Note: If the system already contains 64 DALI devices, the only way to replace a

device is through the “Build System” command.

1. Enter programming mode.

2. Use the Master buttons to highlight “DALI” and press the OK

button to accept.

3. Use the Master buttons to highlight “Address All” and press

the OK button to accept. All DALI devices in the system will

go to full On. As each DALI device is addressed, the Wallbox

Power Module control unit will display information about it,

and the device will go to its low-end. This will take several

minutes. The system will then return to the main menu.

4. To program new/replacement devices, follow the instructions

to assign DALI devices to a zone.

5. Exit programming mode.

6. The Wallbox Power Module with DALI Control Unit cannot

be controlled by the system until it is programmed using the

system programming software.

Main menu

Zone setup

DALI

Assign zone

Address All

DALI

Address All

Address All ?

Press OK

12345691011 12 13 14 7815

9-16

1-8

Master

buttons

button

Searching...

Found

x Loads

Found

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Lutron Electronics Unité de contrôle

Lutron Electronics

Lutron Electronics PowPak RMK-CCO1-24-B Manuel utilisateur

Lutron Electronics

Lutron Electronics PowPak RMJS-CCO1-24-B Manuel utilisateur

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-3PD-1 Manuel utilisateur

Lutron Electronics

Lutron Electronics GRAFIK Eye QS Manuel du propriétaire

Lutron Electronics

Lutron Electronics PowPak FC-SENSOR Manuel utilisateur

Lutron Electronics

Lutron Electronics seeTouch guestroom solutions Manuel utilisateur

Lutron Electronics

Lutron Electronics QS Timeclock Manuel du propriétaire

Lutron Electronics

Lutron Electronics PowPak RMJS-16R-DV-B Manuel utilisateur

Lutron Electronics

Lutron Electronics QSGRK-3PCE Manuel du propriétaire

Lutron Electronics

Lutron Electronics Pico QSR4P-3R Manuel utilisateur

Lutron Electronics

Lutron Electronics PowPak RMJ-5R-DV-B Manuel utilisateur

Lutron Electronics

Lutron Electronics LCP128 Manuel d'utilisation

Lutron Electronics

Lutron Electronics QSE-IO Manuel utilisateur

Lutron Electronics

Lutron Electronics TriPak Series Manuel utilisateur

Lutron Electronics

Lutron Electronics LMM-16R-DV-B Manuel utilisateur

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRJ-3P Mode d'emploi

Lutron Electronics

Lutron Electronics GRAFIK 6000 Manuel utilisateur

Lutron Electronics

Lutron Electronics Grafik Eye GRX-4000 Series Instructions de montage

Lutron Electronics

Lutron Electronics Grafik Eye GRX-4000 Series Manuel utilisateur

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRJ-8E Instructions d'installation et d'utilisation

Lutron Electronics

Lutron Electronics GRAFIK Eye Architrave GRX-4SLB-DW Manuel utilisateur

Lutron Electronics

Lutron Electronics QS Timeclock Mode d'emploi

Lutron Electronics

Lutron Electronics RadioRA RAMC-5W Manuel utilisateur

Lutron Electronics

Lutron Electronics PowPak RMJ-CCO1-24-B Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur