Kramer TP-594Txr Manuel utilisateur

TP-594Txr / TP-594RxrQuick Start

P/N:

2900- 301015QS

Rev:

Scan for full manual

TP-594Txr/TP-594Rxr Quick Start Guide

This guide helps you installand use your TP-594Txr/TP-594Rxr for the first time.

Go to www.kramerav.com/downloads/TP-594Txr, TP-594Rxr todownload the latest user manual and check

if firmwareupgrades are available.

Step 1: Check what’s in the box

TP-594Txr HDMI Line Transmitter or

1 48V DC power adapter andcord for TP-594Txr or

1 Bracket set

TP-594Rxr HDMI Line Receiver

1 12VDCpower adapter and cord for TP-594Rxr

4 Rubber feet

1 Quick start guide

Step 2: Get to know your TP-594Txr / TP-594Rxr

TP-594Txr

Feature

Function

POE STATUS LED

Lights green when power is provided over the HDBT connection.

LINK LED

Lights greenwhen the HDBT link is valid.

IN LED

Lights green when an active source device input signal is detected.

ON LED

Lights green whenthe device receives power.

HDMI™IN Connector

Connect to an HDMI source.

IR 3.5mm Mini Jack Connector

Connect to an external IR emitter tocontrol a local device from the receiver (TP-594Rxr)

side.

Connect to an IR sensor to control aremote device connected tothe TP-594Rxr receiver.

RS-232 3-pin Terminal Block

Connector

Connect to acontroller device (for example, SL-240C) to control a remote device via serial

controller (for example, theHDMIOUT acceptor) that is connected to TP-594Rxr.

AUDIO 5-pin Terminal Block

Connector

Connect to either a stereo balanced audio source or acceptor (the connection typeis

defined via the embedded web pages):

Connect an audio source to extend anaudio signal fromTP-594Txr to the audio acceptor

on thereceiver side via the HDBT line.

Connect an audio acceptor to output theaudio signal received from theaudio sourceon

TP-594Rxr via the HDBT line.

TOSLINK OUT Connector

Digital audio on a TOSLINK optical female connector,for outputting the digital audio signal

that is extended from the receiver to an audio acceptor.

HDBT OUT Connector

Connect tothe RJ-45HDBT IN connector on a receiver (for example, TP-594Rxr or

TP-590Rxr) to extend the signals between the TP-594Txr and the receiver.

SETUP 4-way DIP-switches

Set the operation DIP-switches(see Step 4:Connect the inputsand outputs).

CONTROL RS-232 3-pin Terminal

Block Connector

Connect to aPC to control the device.

CONTROL ETHERNET RJ-45

Connector

Connect to a PC tocontrol the device or for LAN extension.

RESET Recessed Button

Press and hold toreset settings to factory default values.

PROG USB Port

Connect to aUSB memory device to upgradethe firmware.

48V DC Power Terminal Block

Connector

Connect tothe supplied power adapter.

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

TP-594Rxr

Feature

Function

GATEWAY Tx LED

Lights blue to indicate gateway activity ofany RS-232, IRor CEC signals sent, as selected

in the embedded web pages.

GATEWAY Rx LED

Lights blue to indicate gateway activity ofany RS-232, IRor CEC signals received, as

selected in the embedded web pages.

POE STATUS LED

Lights green when power is received over the TP connection.

LINK LED

Lights greenwhen the HDBT link is valid.

ON LED

Lights green whenthe device receives power.

HDMI OUT Connector

Connect to anHDMI acceptor.

IR 3.5mm Mini Jack Connector

Connect to an external IR emitter to control a local device from the transmitter (TP-594Txr)

side.

Connect to an IR sensor to control a remote device connected to the TP-594Txr

transmitter.

RS-232 3-pin Terminal Block

Connector

Connect to an RS-232 deviceto be controlled, for example, a projector.

AUDIO 5-pin Terminal Block

Connector

Connect to astereo balanced audio source or anacceptor (the connection type is defined

via the embedded web pages):

Connect an audio acceptor to output theaudio signal received from the audio source on

the transmitter side via the HDBT line.

Connect an audio sourcetoextend an audio signal from TP-594Rxr tothe audio acceptor

on theTP-594Txr via the HDBT line.

TOSLINK IN Connector

1 digital audio on a TOSLINK optical female connector for digitalaudio input and extension

to thetransmitter.

HDBT IN Connector

Connect to the RJ-45 HDBT OUT connector on atransmitter (for example,

TP-594Txr or TP-590Txr) to extend the signals between TP-594Rxr and thetransmitter.

SETUP 4-way DIP-switches

Set the operation DIP-switches(see Step 4:Connect the inputsand outputs).

CONTROL RS-232 3-pin Terminal

Block Connector

Connect to a PC tocontrol the device.

CONTROL ETHERNET RJ-45

Connector

Connect to a PC tocontrol the device or for LAN extension.

RESET Recessed Button

Press and hold toreset settings to factory default values.

PROG USB Port

Connect to aUSB memory device to upgrade the firmware.

12V DC Power Connector

12V DC connector for powering the unitwhen unit is notpowered via the HDBT link by the

transmitter.

Step 3: Mount TP-594Txr/TP-594Rxr

Install TP-594Txr/TP-594Rxr using oneof the following methods:

•Attach the rubber feet and place the unit on a flat surface.

•Fasten a bracket (included) on each side of the unit and attach it to a flat

surface (see www.kramerav.com/downloads/TP-594Txr.).

•Mount the unit in a rack using the recommended

rack adapter

(see www.kramerav.com/product/TP-594Txr).

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your TP-594Txr/TP-594Rxr. For best results, we

recommend that you always use Kramer high-performance cables to connect AV equipment to TP-594Txr/TP-594Rxr.

Wiring the RJ-45 Connectors

DIP-Switch Settings

For the HDBT connector, see the wiring diagram

below. It isrecommended that the cable ground

shielding be connected/soldered to the

connector shield

All DIP-switches are set to OFF (up) by default except DIP-

switch 1 which is set toON by default.

PIN EIA /TIA 568B

Wire Color

Feature

Dip-switch Settings

Orange / White

Range

Mode

OFF (up) –HDBaseT ultra-long range (provides increased

range at areduced bandwidth).

ON (down) –Normal range.

Orange

Green / White

Blue

The ultra-long rangemode is activated when DIP-

switch 1 on at least oneof the devices is set toON.

Blue / White

Green

Brown / White

Define IR

Pass-

through

OFF (up) –Pass-through the IR signal totheIR port via IR

cable.

ON (down) –Add IR modulation to theIR output signal

(applies only when the IR port is connectedto an IR emitter

cable).

Brown

The IRPass-through DIP-switch setupdepends on

the IR control configuration. We recommend that

you test which position best suits your application.

EDID Lock

Off –EDID is acquired automatically.

On –EDIDlocks the current EDID so that changes onthe

output do not result in changesto the EDID.

For optimum rangeand performance use the

recommended Kramer cables available at

www.kramerav.com/product/TP-594T,TP-594R.

EDID remains locked to auto-EDID changes when

replacing the display device, for example, and does

not apply to manual EDID changes such as EDID

Designer EDID setup and EDID changes due to

panel keys/switches user changes.

N/A

For future use.

Step 5: Connect the power

Connect the 48V DC power supply to TP-594Txr and the 12V DC power supply to the TP-594Rxr and plug both into the

mains electricity.

When TP-594Txr is used as a PoE provider for the TP-594Rxr, you do not need to connect the 12V DC power supply to the

TP-594Rxr unless power supply redundancy is needed.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the Kramer Electronics power adapter that is provided with the unit.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.comfor updatedsafety information.

Step 6: Operate TP-594Txr/TP-594Rxr

OperateTP-594Txr/TP-594Rxr via:

•Remotely, by RS-232

serial commands

transmitted by a touch

screen system, PC, or

other serial controller.

•Embedded web pages

via the Ethernet.

RS-232 Control / Protocol 3000

Baud Rate:

115,200

Parity:

None

Data Bits:

Command Format:

ASCII

Stop Bits:

Example (pass embedded audio to the output): #AUD-EMB 1,2,0<CR>

Default Ethernet Parameters

IP Address:

DHCP enabled

Fallback IP Address:

TP-594Txr: 192.168.1.39; TP-594Rxr 192.168.1.40

Fallback Subnet Mask:

255.255.255.0

TCP Port #:

5000

Fallback:

192.168.1.1

UDP Port #:

50000

Technical Specifications

TP-594Txr

Input

HDMI

On a female HDMI connector

Output

HDBT

On an RJ-45 connector

Optical (Digital Audio)

On a TOSLINK® connector

Input/Output (configurable)

Balanced Stereo Audio

On a 5-pin terminal block connector

TP-594Rxr

Input

HDBT

On an RJ-45 connector

Optical (Digital Audio)

On a TOSLINK® connector

Output

HDMI

On a female HDMI connector

Input/Output (configurable)

Balanced Stereo Audio

On a 5-pin terminal block connector

General

Ports

Ethernet

On an RJ-45 female connector for device control and LAN extension

RS-232

On a 3-pin terminal block for serial link extension

On a 3.5mm mini jack for IR extension

Control RS-232

On a 3-pin terminal block for device control

USB

On a female USB-A connector for device firmware upgrade

Extension

We recommend that you use Kramer shielded cables to achieve optimum extension ranges

Compression

Low-level standard DSC compression for signals above 4K@60 (4:2:0)

4K@60 (4:4:4) Range

Compression: up to 100m (330ft)

4K@60 (4:2:0) Range

No compression: up to 100m (330ft)

Full HD (1080p@60Hz) Range

No compression: up to 130m (430ft)

Ultra-long mode: up to 180m (590ft)

Compliance

HDBaseT 2.0

Video

Max Bandwidth

Compression: 17.95Gbps (5.98Gbps per graphic channel)

No compression: 10.2Gbps (3.4Gbps per graphic channel)

Max Resolution

Compression: 3840x2160@60Hz 4:4:4 24bpp

No compression: 4096x2160@60Hz 4:2:0 24bpp

Compliance

HDMI 2.0, HDCP 2.2, HDR 10

Controls

Front Panel

IN (TP-594Txr only), GATEWAY Tx/Rx (TP-594Rxr only), POE STATUS,

LINK and ON LED indicators

Rear Panel

DIP-switches

Extended RS-232

Baud Rate

300 to 115200baud

Extended Ethernet

Data Rate

Up to 100Mbps

Extended IR

Frequency

20kHz to 100kHz

Power

Consumption

TP-594Txr + TP-594Rxr: 48V DC, 0.65A

TP-594Txr: 48V DC, 0.45A

TP-594Rxr: 12V DC, 1.1A

Source

TP-594Txr: 48V DC, 1.36A

TP-594Rxr: 12V DC, 2A

Environmental Conditions

Operating Temperature

0° to +40°C (32° to 104°F)

Storage Temperature

-40° to +70°C (-40° to 158°F)

Humidity

10% to 90%, RHL non-condensing

Regulatory Compliance

Safety

CE, UL

Environmental

RoHs, WEEE

Enclosure

Size

Tool

Type

Aluminum

Cooling

Convection ventilation

General

Net Dimensions (W, D, H), each

18.7cm x 11.5cm x 2.5cm (7.4" x 4.5" x 1")

Shipping Dimensions (W, D, H)

34.5cm x 16.5cm x 5.2 cm (13.6" x 6.5" x 2")

Net Weight, each

0.4kg (0.9bs) approx.

Shipping Weight

0.95kg (2.1lbs) approx.

Accessories

Included

1 power adapter, 1 power cord and 1 bracket set per device

Specifications are subject to change without notice at www.kramerav.com

Autres manuels pour TP-594Txr

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Kramer Émetteur

Kramer

Kramer TP-581T Manuel utilisateur

Kramer

Kramer TP-145 Manuel utilisateur

Kramer

Kramer TP-551N Manuel utilisateur

Kramer

Kramer TOOLS TP-104 Manuel utilisateur

Kramer

Kramer TP-780T Manuel utilisateur

Kramer

Kramer WP-789T Manuel utilisateur

Kramer

Kramer TP-121EDID Manuel utilisateur

Kramer

Kramer SWT3-41-U-T Manuel utilisateur

Kramer

Kramer 617T Manuel utilisateur

Kramer

Kramer SID-X3N Manuel d'installation et d'exploitation

Kramer

Kramer TP-551N Manuel utilisateur

Kramer

Kramer Cobra TS2 Manuel utilisateur

Kramer

Kramer EXT3-C-WP-XR-T Manuel utilisateur

Kramer

Kramer TP-210A Manuel utilisateur

Kramer

Kramer TA-110HD Manuel utilisateur

Kramer

Kramer SID-X1N Manuel utilisateur

Kramer

Kramer WP-110 Manuel utilisateur

Kramer

Kramer WP-580Txr Manuel utilisateur

Kramer

Kramer TP-121EDID Manuel utilisateur

Kramer

Kramer TP-583T Manuel utilisateur

Kramer

Kramer F-121 Manuel utilisateur

Kramer

Kramer 691 Manuel utilisateur

Kramer

Kramer TP-580CT Manuel utilisateur

Kramer

Kramer SID-X1N Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur