Kohler K-10666 Manuel d'utilisation
Maintenance Guide
Exposed Flush Valve
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página “Español-1”
K-10666, K-10673, K-10674, K-10677
1108709-5-E
Table of Contents
EC Declaration of Conformity ............................. 3
Important Information ................................... 4
Your Kohler Electronic Valve .............................. 4
Care and Cleaning ..................................... 5
Control Stop Valve Operation ............................. 7
Remove the DC Sensor ................................. 9
Replace the Battery ................................... 10
Install the DC Sensor .................................. 11
Remove the Solenoid .................................. 12
Install the Solenoid .................................... 13
Clean the Screen/Replace the Piston ...................... 14
Clean/Replace the Diaphragm ........................... 16
Replace the Vacuum Breaker ............................ 18
Replace the Flush Button Assembly ....................... 19
Warranty ........................................... 19
Troubleshooting ...................................... 21
Service Parts ........................................ 25
1108709-5-E 2 Kohler Co.
EC Declaration of Conformity
declare under our sole responsibility that our products, ELECTRONIC FLUSH VALVES, models:
We,
Kohler Company
444 Highland Drive, Kohler, WI 53044
Phone 920-457-4441
EC DECLARATION OF CONFORMITY
K-10673
to which this declaration relates, are in conformity with the following standards:
Electromagnetic Compatibility Directive 89/336/EEC of 3 May 1989 as Amended by
92/31/EEC of 28 April 1992 and 93/68/EEC, Article 5 of 22 July 1993, based on:
• IEC 61000/ IEC 61000-3-:
"Electromagnetic Compatibility (EMC)";
Part 3: "Limits".
Section 2. "Limits for harmonic current emissions (equipment input current up to and including
16A per phase" (2000).
Section 3. "Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage
supply systems, for equipment with rated current <16 A per phase and not subjected to
conditional connection" (1995 + A1:2001).
• EN 61000-6-2/ EN 61000-6-2:
"Electromagnetic Compatibility (EMC) – Part 6-2: Generic standards – Immunity for industrial
environments" (2001).
• EN 55022 Class B:
"Information technology equipment – Radio disturbance characteristics – Limits and methods of
measurements" (1998 A1:2000 + A2:2003).
Low Voltage Directive 73/23/EEC of 19 February 1973 as Amended by 93/68/EEC, Article 13 of
22 July 1993, based on:
• EN 60730/1:
"Specification for Automatic Electrical Controls for Household and Similar Use. General
Requirements".
• EN 60730/2/8:
"Specification for Automatic Electrical Controls for Household and Similar Use. Particular
Requirements for Electrically Operated Water Valves, Including Mechanical Requirements".
Timothy J. Stessman
Codes & Standards Dept.
Kohler Company
November 18, 2008
DateSignature
November 18, 2008 08
K-10677
K-10674
K-10678
K-10675
K-10679
K-10676 K-10668
K-10666
Kohler Co. 3 1108709-5-E
Important Information
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures.
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the dealer or an experienced radio/television technician
for help.
Modifications: Any modifications made to this device that are not
approved by Kohler Co. may void the authority granted to the user by
the FCC to operate this equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Your Kohler Electronic Valve
Design Features
The valve is designed specifically for use with 1-1/2″(38 mm) top
spud toilets as offered by Kohler Company and others.
The valve is supplied with factory preset timing values. No
programming or adjustment is required.
1108709-5-E 4 Kohler Co.
Your Kohler Electronic Valve (cont.)
Depending upon use,a9Vlithium battery can be expected to last for
two to three years before replacement is required.
Flush Operations
The exposed electronic valve provides the following flushing
operations:
Wave activated main flush operation: When a hand is waved
over the sensor, the valve provides a main flush.
Automatic 24-hour flush operation: After 24-hours of non-use,
the valve produces a full flush.
Low Battery Indication
The 9 V lithium battery can be expected to last for two to three years
before replacement is required. When the battery reaches a certain
point in its lifetime, the valve announces the low battery condition by
continuously flashing an LED whenever a user is in range. The battery
is easily replaced as described in the section ″Replace the Battery″in
this guide.
Replacement batteries can be purchased from drugstores or other stores
stocking batteries. The required battery is a standard 9 V lithium.
Seasonal Use
The exposed electronic valve is not designed for operation in freezing
conditions. If freezing conditions are expected, isolate and drain the
valve along with whatever other winterization steps are taken for the
facility.
Mobile Use
The exposed electronic valve is not designed for use in moving
environments such as boats.
Care and Cleaning
For best results, keep the following in mind when caring for your
KOHLER product:
•Use a mild detergent such as liquid dishwashing soap and warm
water for cleaning. Do not use abrasive cleaners that may scratch
or dull the surface.
Kohler Co. 5 1108709-5-E
Care and Cleaning (cont.)
•Carefully read the cleaner product label to ensure the cleaner is
safe for use on the material.
•Always test your cleaning solution on an inconspicuous area
before applying to the entire surface.
•Do not allow cleaners to sit or soak on the surface.
•Wipe surfaces clean and rinse completely with water immediately
after cleaner application. Rinse and dry any overspray that lands
on nearby surfaces.
•Use a soft, dampened sponge or cloth. Never use an abrasive
material such as a brush or scouring pad to clean surfaces.
For detailed cleaning information and products to consider, visit
www.kohler.com/clean. To order Care & Cleaning information, call
1-800-456-4537.
1108709-5-E 6 Kohler Co.
Control Stop Valve Operation
NOTICE: Refer to this section throughout the Maintenance Guide
when instructed to close and open the control stop valve.
General Adjustment Instructions
Use a strap wrench to remove the vandal-resistant cap from the
control stop valve.
Close the stop valve by turning the valve screw clockwise as far
as it can go.
Open the stop valve by turning the valve screw counterclockwise
as far as it can go.
When done, place the stop cap on the control stop valve and
tighten using a strap wrench.
Control Stop Adjustment
NOTE: To adjust the control stop to achieve peak performance of 25
gpm (95 lpm) perform the steps below.
Use a strap wrench to remove the vandal-resistant cap from the
control stop valve.
Close the control stop (clockwise) all the way.
Open the control stop 1/4 turn (counterclockwise).
Test flush the fixture.
Repeat until excessive splashing occurs during the flush.
Wall Flange
Wall Tube
Control Stop
Stop Cap
Kohler Co. 7 1108709-5-E
Control Stop Valve Operation (cont.)
If excessive splashing occurs during the test flush, close the
control stop 1/4 turn.
Test flush.
If splashing is at an acceptable level this is the optimal setting. If
excessive splashing occurs during the test flush, close the control
stop another 1/4 turn and test.
Repeat until the optimal setting is found.
1108709-5-E 8 Kohler Co.
Remove the DC Sensor
Using a 3/32″hex head wrench, remove the setscrew from the
valve cap.
Remove the cap by carefully lifting from the valve body.
Disconnect the DC sensor connector to the solenoid by grasping
each side of the connector pair and pulling apart. Do not separate
the connector pair by pulling on the wires.
Position the cap on its side and look inside.
Remove the battery.
Remove the screws that hold the DC sensor in place inside the
cap.
Turn the cap over and slide the DC sensor, sensor strap, and
screws into your hand.
NOTE: The battery inside the sensor may be considered hazardous
waste. Discard the old DC sensor and/or battery in accordance with
any applicable codes.
If replacing the DC sensor, discard the old DC sensor and battery.
Cap
Setscrew
DC Sensor
DC Sensor
Connector
Sensor Strap
Screw
Kohler Co. 9 1108709-5-E
Replace the Battery
NOTE: When purchasing a replacement battery, selecta9Vlithium
battery.
NOTE: It is not necessary to remove the sensor from the cap to
replace the battery.
Using a 3/32″hex wrench, remove the setscrew from the cap.
Remove the cap.
Using a small, flat-blade screwdriver (if necessary), carefully pry
the battery from the cap.
Disconnect the battery and remove the battery boot.
NOTE: The battery may be considered hazardous waste. Discard
the old battery in accordance with any applicable codes.
Discard the old battery.
Connect the new battery. Install the battery boot over the
connections.
Reinstall the battery into the cap.
Reinstall the cap.
Battery
Setscrew
Battery Boot
Cap
1108709-5-E 10 Kohler Co.
Ce manuel convient aux modèles suivants
3
Table des matières
Langues :
Autres manuels Kohler Unité de contrôle
Kohler
Kohler K-10675 Manuel utilisateur
Kohler
Kohler 5-10EKD Manuel utilisateur
Kohler
Kohler 28138T Manuel utilisateur
Kohler
Kohler K-11842 Series Instructions de montage
Kohler
Kohler K-10970 Instructions de montage
Kohler
Kohler K-682 Manuel utilisateur
Kohler
Kohler K-10675 Manuel d'utilisation
Kohler
Kohler K-728 Instructions de montage
Kohler
Kohler K-304 Instructions de montage
Kohler
Kohler K-10956 Manuel d'utilisation
Kohler
Kohler DTV+ Konnect K-97999-NA Manuel utilisateur
Kohler
Kohler K-10959 Manuel utilisateur
Kohler
Kohler 880A Manuel utilisateur
Kohler
Kohler K-306 Manuel utilisateur
Kohler
Kohler Mira Select B14C Manuel utilisateur
Kohler
Kohler DTV+ Instructions de montage
Kohler
Kohler BEAM K-77691K-G Manuel utilisateur
Kohler
Kohler 1216612 Manuel utilisateur
Kohler
Kohler K-10673 Manuel d'utilisation
Kohler
Kohler TOUCHLESS K-13686 Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
