Keysight Technologies PNA Series Manuel utilisateur

IINSTALLATION AND QUICK START GUIDE

)

Keysight

PNA Series

Network Analyzers

This is Installation and Operataing Guide for upgrading the PNA Series Microwave Network Analyzers.

Notices

2009-2022

No part of this manual may be

reproduced in any form or by any

means (including electronic storage

and retrieval or translation into a

foreign language) without prior

agreement and written consent from

Keysight Technologies, Inc. as

governed by United States and

international copyright laws.

Trademark Acknowledgments

Manual Part Number

E8356-90001

Edition

Edition 2, October 2022

Printed in USA/Malaysia

Published by:

Keysight Technologies

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Warranty

THE MATERIAL CONTAINED IN THIS

DOCUMENT IS PROVIDED “AS IS,”

AND IS SUBJECT TO BEING

CHANGED, WITHOUT NOTICE, IN

FUTURE EDITIONS. FURTHER, TO

THE MAXIMUM EXTENT PERMITTED

BY APPLICABLE LAW, KEYSIGHT

DISCLAIMS ALL WARRANTIES,

EITHER EXPRESS OR IMPLIED WITH

REGARD TO THIS MANUAL AND

ANY INFORMATION CONTAINED

HEREIN, INCLUDING BUT NOT

LIMITED TO THE IMPLIED

WARRANTIES OF

MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE.

KEYSIGHT SHALL NOT BE LIABLE

FOR ERRORS OR FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES IN

CONNECTION WITH THE

FURNISHING, USE, OR

PERFORMANCE OF THIS

DOCUMENT OR ANY INFORMATION

CONTAINED HEREIN. SHOULD

KEYSIGHT AND THE USER HAVE A

SEPARATE WRITTEN AGREEMENT

WITH WARRANTY TERMS

COVERING THE MATERIAL IN THIS

DOCUMENT THAT CONFLICT WITH

THESE TERMS, THE WARRANTY

TERMS IN THE SEPARATE

AGREEMENT WILL CONTROL.

Technology Licenses

The hardware and/or software

described in this document are

furnished under a license and may be

used or copied only in accordance

with the terms of such license.

U.S. Government Rights

The Software is “commercial

computer software,” as defined

by Federal Acquisition Regulation

(“FAR”) 2.101. Pursuant to FAR

12.212 and 27.405-3 and

Department of Defense FAR

Supplement (“DFARS”) 227.7202,

the U.S. government acquires

commercial computer software

under the same terms by which

the software is customarily

provided to the public.

Accordingly, Keysight provides

the Software to U.S. government

customers under its standard

commercial license, which is

embodied in its End User License

Agreement (EULA), a copy of

which can be found at

http://www.keysight.com/find/sweula

The license set forth in the EULA

represents the exclusive authority

by which the U.S. government

may use, modify, distribute, or

disclose the Software. The EULA

and the license set forth therein,

does not require or permit,

among other things, that

Keysight: (1) Furnish technical

information related to

commercial computer software

or commercial computer

software documentation that is

not customarily provided to the

public; or (2) Relinquish to, or

otherwise provide, the

government rights in excess of

these rights customarily provided

to the public to use, modify,

reproduce, release, perform,

display, or disclose commercial

computer software or

commercial computer software

documentation. No additional

government requirements

beyond those set forth in the

EULA shall apply, except to the

extent that those terms, rights, or

licenses are explicitly required

from all providers of commercial

computer software pursuant to

the FAR and the DFARS and are

set forth specifically in writing

elsewhere in the EULA. Keysight

shall be under no obligation to

update, revise or otherwise

modify the Software. With

respect to any technical data as

defined by FAR 2.101, pursuant

to FAR 12.211 and 27.404.2 and

DFARS 227.7102, the U.S.

government acquires no greater

than Limited Rights as defined in

FAR 27.401 or DFAR 227.7103-5

(c), as applicable in any technical

data.

Safety Notices

A CAUTION notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly

performed or adhered to, could

result in damage to the product

or loss of important data. Do not

proceed beyond a CAUTION

notice until the indicated

conditions are fully understood

and met.

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly

performed or adhered to, could

result in personal injury or death.

Do not proceed beyond a

WARNING notice until the

indicated conditions are fully

understood and met.

Keysight PNA Series Network Analyzers

Upgrade Kit Order Numbers: E8356-90001

Installation Note

In This Guide

This guide contains the following information:

—“Getting Assistance from Keysight” on page 4

This section contains some general information and information on how to

contact Keysight for support on your product.

—“Operating Precautions” on page 6

This section discusses how to care for your instrument and to avoid

damaging your instrument.

—“Installing Your Analyzer” on page 10

This section discusses how to install your PNA.

—“Windows 10 Operating System (B Models Only)” on page 18

This section discusses the Windows 10 Operating System that is installed

on PNA (B models only).

—“Getting Help with Your Analyzer” on page 18

This section discusses where to go for resources to help with using your

PNA.

—“Safety, Regulatory, and Environmental Information” on page 19

This section contains the safety, regulatory, and environmental information

on your PNA.

IMPORTANT! Much of the information in this document refers to Windows

10, but your instrument might have Windows 7 installed. This document is

applicable to both Windows 7 and Windows 10 operating systems.

4 Installation Note E8356-90001

In This Guide

Getting Assistance from Keysight

Installing this upgrade kit requires special skills and experience. If you think

you may not be qualified to do the work, or need advice, contact Keysight.

Contacting Keysight

Assistance with test and measurements needs and information on finding a

local Keysight office are available on the Web at:

http://www.keysight.com/find/assist

If you do not have access to the Internet, please contact your Keysight field

engineer.

In any correspondence or telephone conversation, refer to the Keysight

product by its model number and full serial number. With this information, the

Keysight representative can determine whether your product is still within its

warranty period.

Technology Licenses

The hardware and / or software described in this document are furnished under

a license and may be used or copied only in accordance with the terms of such

license.

Trademarks

Microsoft is a U.S. registered trademark of Microsoft Corporation. Windows

and MS Windows are U.S. registered trademarks of Microsoft Corporation.

For optimum service, before contacting Keysight, it is important to sign up

for Keysight Care to improve turnaround time and committed service levels

on both application support as well as post-sales support.

Learn more http://www.keysight.com/find/keysightcare.portal.

To contact Keysight for sales and technical support, refer to support links

on the following Keysight websites: http://www.keysight.com/find

(product specific information and support, software and documentation

updates) http://www.keysight.com/find/assist (worldwide contact

information for repair and service).

Installation Note E8356-90001 5

In This Guide

Getting Assistance from Keysight

Safety Symbols

The following safety symbols are used throughout this manual. Familiarize

yourself with each of the symbols and its meaning before operating this

instrument.

Documentation Map

The online Help file is embedded in the analyzer, offering quick reference to

programming and user documentation. PNA Help is available in English only.

The Installation and Quick Start Guide helps to quickly familiarize yourself with

the analyzer. Procedures are provided for installing, configuring, and verifying

the operation of the analyzer.

Downloading PNA Documentation from the Web

Documentation for all PNA models is available by going to:

https://www.keysight.com/ entering your PNA model number, and clicking on

Technical Support.

Denotes a hazard. It calls attention to a procedure that, if not correctly

performed or adhered to, would result in damage to or destruction of the

product. Do not proceed beyond a caution note until the indicated

conditions are fully understood and met.

Denotes a hazard. It calls attention to a procedure which, if not

correctly performed or adhered to, could result in injury or loss of

life. Do not proceed beyond a warning note until the indicated

conditions are fully understood and met.

6 Installation Note E8356-90001

In This Guide

Operating Precautions

Preventing Electrostatic Discharge Damage

Protection against electrostatic discharge (ESD) is essential while removing

assemblies from or connecting cables and assemblies (DUT) to the network

analyzer. Static electricity can build up on your body and can easily damage

sensitive internal circuit elements when discharged. Static discharges too

small to be felt can cause permanent damage. To prevent damage to the

instrument:

— always have a grounded, conductive table mat in front of your test

equipment.

— always wear a grounded wrist strap, connected to a grounded conductive

table mat, having a 1 MΩresistor in series with it, when handling

components and assemblies or when making connections.

— always wear a heel strap when working in an area with a conductive floor. If

you are uncertain about the conductivity of your floor, wear a heel strap.

— always ground yourself before you clean, inspect, or make a connection to a

static-sensitive device or test port. You can, for example, grasp the

grounded outer shell of the test port or cable connector briefly.

— always ground the center conductor of a test cable and DUT before making

a connection to the analyzer test port or other static-sensitive device. This

can be done as follows:

1. Connect a short (from your calibration kit) to one end of the cable and DUT

to short the center conductor to the outer conductor.

2. While wearing a grounded wrist strap, grasp the outer shell of the cable

and DUT connector.

3. Connect the other end of the cable to the test port.

4. Remove the short from the cable.

Most causes of instrument failure can be avoided if you will apply

the information in this section. PLEASE READ!

Installation Note E8356-90001 7

In This Guide

Operating Precautions

Figure 0-1 ESD Protection Setup

The following table lists Keysight part numbers for ESD protection devices. To

order, refer to “Contacting Keysight” on page 4.

Preventing Electrical Overstress Damage

Excessive RF power or voltage applied to the ports and connectors on the front

panel will damage the analyzer. Each port and front-panel connector has a

label (see photo below) that shows damage levels. These levels must not be

exceeded. Damage levels are also listed in the Specifications section of the

analyzer's Help system.

There are two ways to protect the PNA input ports from high RF power:

1. Use power limiters at the ports. Information on limiters can be found at:

www.keysight.com/find/mta.

2. Apply the recommendations in PNA Application Note 1408-10,

“Recommendations for Testing High-Power Amplifiers,” found at:

https://www.keysight.com/us/en/assets/9921-01766/user-manuals/User

s-Guide-A-Series-N991xA-2xA-3xA-5xA-6xA-Unabridged.pdf

(5989-1349EN).

Description Keysight Part Number

Grounding wrist strap 9300-1367

5-ft grounding cord for wrist strap 9300-0980

2 x 4 ft conductive table mat and 15-ft grounding wire 9300-0797

8 Installation Note E8356-90001

In This Guide

Operating Precautions

Figure 1 Example Label Showing Damage Level for Each Port and Connector

Preventing Test Port Connector Damage

Proper connector care and connection techniques are critical for accurate and

repeatable measurements. The following table contains for tips on connector

care.

For more information on the proper use and maintenance of connectors, see

https://rfmw.em.keysight.com/wireless/helpfiles/N52xxB/Tutorials/Connect

or_Care.htm.

Observe Proper Shutdown Procedures

To turn the PNA OFF, BRIEFLY press the front panel On/Standby switch. The

PNA will then begin to shutdown.

The On/Standby indicator changes from green to yellow when power is Off.

Installation Note E8356-90001 9

In This Guide

Operating Precautions

Do NOT Modify or Reconfigure the Operating System

The Microsoft Windows operating system has been modified and optimized by

Keysight to improve the performance of the PNA.

— Do NOT install a standard version of the Windows operating system on the

PNA.

— Do NOT change advanced performance settings or group policies.

— Do NOT add or delete any SSD partitions on the PNA.

— Do NOT delete the Keysight user account unless in a secured environment.

— Do NOT modify any of the Keysight software registry entries.

— DO NOT disconnect mains power to shutdown the PNA, except when

absolutely necessary. Doing so can damage the power supply, solid state

drive, or other internal assemblies.

Install Antivirus and Firewall Protection

No antivirus software is shipped with the analyzer. It is recommended that you

install antivirus software if your analyzer is connected to the LAN. Check with

your IT department to see what they recommend.

The analyzer is shipped with the Windows firewall and Windows Defender

enabled.

Do not modify the default network settings as this may cause problems with

the operating system of the analyzer.

To adjust Windows Defender settings, log in as administrator (refer to “User

Accounts” in the PNA Online Help,

https://rfmw.em.keysight.com/wireless/helpfiles/N52xxB/help.htm) and

minimize the PNA-Series Application and click on the Start button and type:

defender

Then click on Windows Defender from the Best match column.

Install Spyware Protection

There is no anti-spyware software installed on the instrument. This should not

be a problem if you do not use the instrument for a lot of internet browsing.

Having spyware in the instrument could have an impact on the instrument

performance.

10 Installation Note E8356-90001

In This Guide

Installing Your Analyzer

Firmware Downgrades

Do not downgrade the PNA firmware below the version that was installed by

the factory. Many components require a minimum firmware revision to run

properly. Downgrading below this version will render the hardware inoperable.

Reversing this firmware downgrade may not recover the hardware operation.

For example, the Direct Digital Synthesizers require firmware A.14.xx and

above. Downgrading to older firmware will permanently disable the hardware.

Installing Your Analyzer

Overview of the Installation Procedure

“Step 1. Check the Shipment.”

“Step 2. Meet Requirements.”

“Step 3. Install the Analyzer.”

“Step 4. Connect the Accessories.”

“Step 5. Ferrite Cores.”

“Step 6. Start Up the Analyzer.”

“Step 7. Perform Administrative Tasks.”

“Step 8. Run the Operator's Check.”

“Step 9. Turn Off the Analyzer.”

STOP!

Do not downgrade the firmware on your PNA below the version that was

installed at the factory, because it will render the hardware inoperable.

Safety of any system incorporating the equipment is the responsibility of

the assembler of the system.

Only Keysight approved accessories shall be used.

This procedure requires an open or short calibration standard that mates

with the front panel test ports. The open or short calibration standard is

NOT included with the PNA.

Autres manuels pour PNA Series

Table des matières

Autres manuels Keysight Technologies Instrument de mesure

Keysight Technologies

Keysight Technologies M9602A Manuel utilisateur

Keysight Technologies

Keysight Technologies P5000A Series Manuel utilisateur

Keysight Technologies

Keysight Technologies N5247B Manuel utilisateur

Keysight Technologies

Keysight Technologies N5221A Manuel utilisateur

Keysight Technologies

Keysight Technologies PD1000A Manuel utilisateur

Keysight Technologies

Keysight Technologies E4980A Manuel de l'opérateur

Keysight Technologies

Keysight Technologies U9361F Manuel utilisateur

Keysight Technologies

Keysight Technologies 34972A Manuel utilisateur

Keysight Technologies

Keysight Technologies N9000B Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies ENA Series Manuel utilisateur

Keysight Technologies

Keysight Technologies U8903B Manuel utilisateur

Keysight Technologies

Keysight Technologies P50 B Series Manuel utilisateur

Keysight Technologies

Keysight Technologies N5244/5B Manuel utilisateur

Keysight Technologies

Keysight Technologies B1507A Manuel utilisateur

Keysight Technologies

Keysight Technologies MXA Series Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies E4980A Guide de démarrage rapide

Keysight Technologies

Keysight Technologies N9000A Manuel utilisateur

Keysight Technologies

Keysight Technologies N5221B Manuel utilisateur

Keysight Technologies

Keysight Technologies N9020A Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies N432A Manuel utilisateur

Keysight Technologies

Keysight Technologies N9020A Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies X-Series Manuel utilisateur

Keysight Technologies

Keysight Technologies U5303A Guide de l'utilisateur

Keysight Technologies

Keysight Technologies FieldFox N9912A104 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur