Keysight Technologies E4980A Manuel de l'opérateur

Quick Demo Guide

Keysight Technologies E4980A Precision LCR Meter, 20 Hz to 2 MHz

E4980A Precision LCR Meter

Procedure overview

1. Preset system

2. Perform compensation of xture

3. Set measurement parameters

4. Connect DUT and measure at a single frequency

5. Set up list sweep table

6. Set trigger mode and make sweep measurement

In this demo...

– Measurement of chip SMD device

– Fixture compensation

– List sweep

Required Instrument and xture

Fixture for SMD device

(16034E/G/H, 16334A)

If the xture for SMD device is not available, it is pos-

sible to perform the same procedure with following

xtures. Use lead components in this case.

16047D 16089A/B/C/D/E16047E

1. Preset system

a. Press [Preset] front panel key

b. Press CLEAR SET&CORR softkey

c. Press OK softkey (wait about 20 seconds…)

2. Perform compensation of xture

a. Set xture to UNKNOWN terminals

b. Press [Meas Setup] front panel key

c. Select CORRECTION softkey

d. Move cursor onto OPEN eld by pressing

[▼] front panel key

e. Make open condition for the test xture

To make open condition, adjust the distance of the

two electrodes so that the separation becomes equal

to the length of the DUT (Figure 1)

f. Press MEAS OPEN softkey to perform open

correction

g. Press ON softkey

To activate Open correction, the status of the OPEN

eld should be changed from “OFF” to “ON.” (Figure 2)

Figure 1. Make open condition (for 16034E/G/H).

Figure 2. Turned on OPEN correction.

h. Make short condition for the test xture

i. Move cursor onto SHORT eld by pressing

[▼] front panel key

j. Press MEAS SHORT softkey to perform short

correction

k. Press ON softkey

To make short condition, short the test xture by

sliding the right (HIGH) electrode to the left so that

two electrodes contact to each other

www.keysight.com/nd/lcrmeters

This information is subject to change without notice.

Published in USA, August 1, 2014

5990-8373EN

www.keysight.com

Keysight | E4980A Precision LCR Meter, 20 Hz to 2 MHz – Demo Guide

3. Set measurement parameters

a. Press [Display Format] front panel key

b. Move cursor onto FUNC eld by pressing [▼] front

panel key

c. Press MORE softkey

d. Press Z-… softkey

e. Press Z-Fdsoftkey

f. Move cursor onto FREQ eld by pressing [▼] front

panel key

g. Enter 1 MHz (press [1] front panel key then press M

softkey)

4. Connect DUT and measure at single

frequency

a. Connect DUT to the test xture

b. You will see the impedance value (Z) at spot

frequency (Figure 3)

Impedance value can be calculated by following

formula. Inductive device: Z = 2 * PI * frequency * L

Capacitive device: Z = 1 / (2 * PI * frequency * L)

Figure 3. Measured value of 10 uH inductor at 1 MHz.

5. Setup list sweep table (sweep frequency

from 1 kHz to 2 MHz, 201 points)

a. Press [Meas Setup] front panel key

b. Press LIST SETUP softkey

c. Move cursor onto FREQ[Hz] eld by pressing [▼]

front panel key (4 times)

d. Enter 1 kHz (press [1] front panel key then press k

softkey)

e. Press PREV PAGE softkey

f. Enter 2 MHz (press [2] front panel key then press M

softkey)

g. Press FILL LOG softkey

h. Press NEXT PAGE softkey to see that the list

frequency is lled up (Figure 4)

Figure 4. List frequency lled up.

6. Set trigger mode and make measurement

a. Press [Meas Setup] front panel key

b. Move cursor onto TRIG INT eld by pressing [▼]

front panel key (4 times)

c. Press MAN softkey

d. Press [Display Format] front panel key

e. Press LIST SWEEP softkey

f. Press [Trigger] front panel key to make

measurement

By using E4980A Data Transfer Program, measure-

ment data can be easily transferred from the E4980A

to a PC (Figure 5). Visit Keysight website to download

the program.

Figure 5. E4980A Data Transfer Program.

Autres manuels pour E4980A

Autres manuels Keysight Technologies Instrument de mesure

Keysight Technologies

Keysight Technologies 34980A Manuel utilisateur

Keysight Technologies

Keysight Technologies B2901A Manuel utilisateur

Keysight Technologies

Keysight Technologies E5061B Manuel utilisateur

Keysight Technologies

Keysight Technologies U4301 Manuel utilisateur

Keysight Technologies

Keysight Technologies MXA N9020A Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies N9030B Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies X-Series Manuel utilisateur

Keysight Technologies

Keysight Technologies FieldFox N9912A Manuel du propriétaire

Keysight Technologies

Keysight Technologies M9710A Guide rapide

Keysight Technologies

Keysight Technologies N9030A Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies EXA N9010B Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies EXA N9010A Manuel utilisateur

Keysight Technologies

Keysight Technologies i7090 Manuel utilisateur

Keysight Technologies

Keysight Technologies X Series Manuel utilisateur

Keysight Technologies

Keysight Technologies P Series Manuel utilisateur

Keysight Technologies

Keysight Technologies P Series Mode d'emploi

Keysight Technologies

Keysight Technologies 11590B Manuel de service

Keysight Technologies

Keysight Technologies U4164A Manuel utilisateur

Keysight Technologies

Keysight Technologies E5868A Instructions de montage

Keysight Technologies

Keysight Technologies CX3300 Series Manuel utilisateur

Keysight Technologies

Keysight Technologies 34420A Manuel utilisateur

Keysight Technologies

Keysight Technologies M9451A Guide de l'utilisateur

Keysight Technologies

Keysight Technologies N9029AV01-V19 Manuel utilisateur

Keysight Technologies

Keysight Technologies C Series Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur