Johnson 40-6602 Manuel utilisateur
©2010 Johnson Level & Tool - Rev. 1 1
Self-Leveling Cro -Line La er Level
with 3 Vertical Line
Model No. 40-6602
Instruction Manual
Congratulations on your choice of this Self-Leveling Cross-Line Laser
Level with 3 vertical lines. We suggest you read this instruction
manual thoroughly before using the instrument. Save this instruction
manual for future use.
This laser emits one laser beam cross and two vertical lines at 90º.
The laser features quick damping, visual and audible out of range
indication, and a pendulum-locking design. Beam visibility depends
upon lighting conditions in the work area.
This is a Class IIIa laser tool and is manufactured to comply with CFR 21,
parts 1040 .10 and 1040 .11 as well as international safety rule IEC 285.
4069H_Manuals 11/5/10 8:49 AM Page 1
2©2010 Johnson Level & Tool - Rev. 1
Table of Contents
1. it Contents
2. Features and Functions
3. Safety Instructions
4. Location/Content
of Warning Labels
5. Location of Parts/Components
6. Operating Instructions
7. Using the Product
8. Self-Check & Fine Calibration
9. Technical Specifications
10. Application Demonstrations
11. Care and Handling
12. Product Warranty
13. Warranty Registration
14. Accessories
1. Kit Contents
Description Qty.
Self-Leveling Cross-Line Laser Level
with 3 Vertical Lines 1
Tripod/Wall Mount Bracket 1
“AA” Alkaline Batteries 3
Tinted Goggles 1
Magnetic Target 1
Instruction Manual with Warranty Card 1
Soft-Sided Carrying Case 1
2. Features and Functions
• Indoor and outdoor use (for outdoor use, must use 40-6780
detector, not included)
• Simultaneously projects three vertical lines and one horizontal
line to form a cross line in front of the laser.
• Locking mechanism protects inner pendulum during transportation.
• Self-leveling with visual and audible alarms when beyond
leveling range.
• Emits continuously both a solid and pulse beam (pulse beam
for use with detector).
• Manual mode allows unit to tilt to extreme angles.
4069H_Manuals 11/5/10 8:49 AM Page 2
©2010 Johnson Level & Tool - Rev. 1 3
3. Safety Instructions
Please read and understand all of the following instructions, prior
to using this tool. Failure to do so, may void the warranty.
DANGER!
Class IIIa Laser Product
Max. Power Output: ≤5mW
Wavelength: 625-645nm
THIS T L EMITS LASER RADIATI N.
D N T STARE INT BEAM.
AV ID DIRECT EYE EXP SURE.
ATTENTION IMPORTANT
• Read all instructions prior to operating this laser tool. Do not remove any labels from tool.
• Do not stare directly at the laser beam.
• Do not project the laser beam directly into the eyes of others.
• Do not set up laser tool at eye level or operate the tool near a reflective surface as
the laser beam could be projected into your eyes or into the eyes of others.
• Do not place the laser tool in a manner that may cause someone to unintentionally
look into the laser beam. Serious eye injury may result.
• Do not operate the tool in explosive environments, i.e. in the presence of gases or
flammable liquids.
• eep the laser tool out of the reach of children and other untrained persons.
• Do not attempt to view the laser beam through optical tools such as telescopes as
serious eye injury may result.
• Always turn the laser tool off when not in use or left unattended for a period of time.
• Remove the batteries when storing the tool for an extended time (more than 3 months)
to avoid damage to the tool should the batteries deteriorate.
• Do not attempt to repair or disassemble the laser tool. If unqualified persons attempt
to repair this tool, warranty will be void.
• Use only original Johnson®parts and accessories purchased from your Johnson®
authorized dealer. Use of non-Johnson®parts and accessories will void warranty.
4069H_Manuals 11/5/10 8:49 AM Page 3
4©2010 Johnson Level & Tool - Rev. 1
4. Location/Content of Warning Labels
4069H_Manuals 11/5/10 8:49 AM Page 4
©2010 Johnson Level & Tool - Rev. 1 5
5. Location of Part/Components
Laser
Emitting
Window
eypad
Battery Door
Screw
Battery Door
6V Plug
(adapter
not included)
Laser
Emitting
Window
Wall Mount Screw Hole
Bench Mark Locator Insert
5/8” thread
Graduated Circle
4069H_Manuals 11/5/10 8:49 AM Page 5
6©2010 Johnson Level & Tool - Rev. 1
6. perating Instructions
IMP RTANT: It is the responsibility of the user to verify the
calibration of the instrument before each use.
Battery In tallation
Note: Always check to be sure that the on/off switch is in the off
position before removing and replacing batteries.
Loosen the battery door screw, put 3 x AA alkaline batteries into the
battery case according to the polarity indication shown in the
battery case. Then put the cover back on and tighten the battery
door screw.
Note:
• Pay attention to the polarity of the batteries.
• Used (discharged) batteries are hazardous waste and should be
disposed of properly.
Battery Door Screw
4069H_Manuals 11/5/10 8:49 AM Page 6
©2010 Johnson Level & Tool - Rev. 1 7
Wall Mount/Tripod Adapter
1. Put the instrument into the tripod/wall mount. The unit can
rotate 360º.
2. The wall mount can be mounted on a wall.
3. The benchmark locator insert can be used to find a point on
the ground.
4. The tripod/wall mount can be attached to a tripod.
Rotating 360º
Hanging on Wall
Connected to a tripod
Put the bench
mark locator
into 5/8” screw
thread hole.
Put the center
of the bench-
mark locator
on the mark
on the floor,
then put in the
instrument.
Benchmark locator insert usage
4069H_Manuals 11/5/10 8:49 AM Page 7
8©2010 Johnson Level & Tool - Rev. 1
7. Using the Product
Power LED:
Light On: Power on
Light Off: Power off
Light Flashing: Low Battery
Pulse mode LED:
Light On: Pulse mode on and the laser can be used with the
40-6780 detector (not included)
Light Off: Pulse mode is off
Manual mode LED:
Light On: Manual mode is on and laser can be turned on with
compensator locked
Light Off: Manual mode is off
Note: When manual mode is on, the laser does not self-level and
no out-of-level alarm is indicated.
Manual mode LED
Manual mode button
Power LED
Vertical laser line buttons
Pulse mode button
Pulse mode LED
Horizontal laser line button
4069H_Manuals 11/5/10 8:49 AM Page 8
©2010 Johnson Level & Tool - Rev. 1 9
Compensator Transportation Lock
Hold the upper housing of the instrument, and turn the base in the
direction of the arrow.
When the instrument is in the “Unlock” position, the power LED will light.
When the instrument is in the “Lock” position, the power LED will be off.
Pulse Mode:
Unlock the transportation lock and press the horizontal and/or vertical
laser line buttons. Then press the pulse mode button to turn on the
pulse mode, the pulse mode LED will turn on and the laser beam line
will dim. The laser line can now be located by a detector (not included).
Press the pulse mode button again to switch off the pulse mode, the
pulse mode LED will turn off. The laser line now can not be located
with a detector.
Manual Mode:
Press the manual mode button with the transportation lock knob in
the “Locked” position. The power LED will light and the manual
To lock the compensator transportation
lock, turn the base to the off position.
To unlock the compensator transportation
lock, turn the base to the on position.
on/off
4069H_Manuals 11/5/10 8:49 AM Page 9
10 ©2010 Johnson Level & Tool - Rev. 1
mode LED will flash. The instrument is now in the manual mode.
Note: When manual mode is on, the laser does not self-level and
no out-of-level alarm is indicated.
Press the manual mode button again and the instrument will power off.
1. If the instrument is in manual mode and the instrument is turned to
the “Unlock” position, the instrument will exit manual mode and
enter self-leveling mode.
2. If the instrument is in the “Unlock” position, pressing the manual
mode button will not get a response.
utput of the laser line
Press button to form the hori-
zontal laser line above
Press button to form the verti-
cal laser line as shown above
Press button to form the two
vertical laser lines shown above
Press all buttons to form the laser
lines shown above
4069H_Manuals 11/5/10 8:49 AM Page 10
Table des matières
Autres manuels Johnson Niveau laser
Johnson
Johnson 40-6174 Manuel utilisateur
Johnson
Johnson 5700-0800LZR Manuel utilisateur
Johnson
Johnson 40-6080 Manuel utilisateur
Johnson
Johnson 40-6532 Manuel utilisateur
Johnson
Johnson 40-6936 Manuel utilisateur
Johnson
Johnson 1880-2400 Manuel utilisateur
Johnson
Johnson 1888-0700 Manuel utilisateur
Johnson
Johnson 40-6065 Manuel utilisateur
Johnson
Johnson 40-6028 Manuel utilisateur
Johnson
Johnson HOT SHOT 9105/40-0910 Manuel utilisateur
Johnson
Johnson 40-0612 Manuel utilisateur
Johnson
Johnson 9100 Manuel utilisateur
Johnson
Johnson 40-6060 Manuel utilisateur
Johnson
Johnson 40-6688 Manuel utilisateur
Johnson
Johnson 40-6646 Manuel utilisateur
Johnson
Johnson 40-6685 Manuel utilisateur
Johnson
Johnson 40-6184 Manuel utilisateur
Johnson
Johnson 40-6636 Manuel utilisateur
Johnson
Johnson 40-6616 Manuel utilisateur
Johnson
Johnson 40-6535 Manuel utilisateur
