Johnson Controls Facility Explorer FX20 Manuel utilisateur

Installation Instructions FX20/60 RS-232

Issue Date April 9, 2014

Part No. 24-10174-85, Rev.C

FX Supervisory Controllers RS-232 Card

Installation Instructions

Applications

The RS-232 option card provides RS-232

communications capability to the FX

Supervisory Controllers. You can install up to

two RS-232 option cards per FX Supervisory

Controller. The port assignments are shown in

Figure 1.

For related information on FX Supervisory

Controllers mounting and wiring, refer to the

FX Supervisory Controllers Installation

Instructions (Part No. 24-10174-77).

Figure 1: FX Supervisory Controllers

RS-232 Card

North American Emissions

Compliance

United States

This equipment has been tested and found to

comply with the limits for a Class A digital

device pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference when this equipment is operated

in a commercial environment. This equipment

generates, uses, and can radiate radio

frequency energy and, if not installed and

used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area may cause

harmful interference, in which case the users

will be required to correct the interference at

their own expense.

Canada

This Class (A) digital apparatus meets all

requirements of the Canadian Interference-

Causing Equipment Regulations.

Cet appareil numérique de la Classe (A)

respecte toutes les exigences du Règlement

sur le matériel brouilleur du Canada.

2FX Supervisory Controllers RS-232 Card Installation Instructions

Installation

Unpack the RS-232 option card and inspect

the contents of the package for damaged or

missing components. If the option card is

damaged, notify the appropriate carrier and

return any damaged components for repair or

replacement.

Parts Included

Included in this package are the following

items:

one RS-232 option card, along with

connector end plate

FX Supervisory Controllers RS-232 Card

Installation Instructions (Part No.

24-10174-85)

Special Tools Needed

To install the RS-232 card, use a number 2

Phillips screwdriver.

WARNING: Risk of Electric Shock.

Disconnect the power supply before making

electrical connections. Contact with

components carrying hazardous voltage can

cause electric shock and may result in

severe personal injury or death.

AVERTISSEMENT: Risque de décharge

électrique. Débrancher l'alimentation avant

de réaliser tout branchement électrique.

Tout contact avec des composants

conducteurs de tensions dangereuses

risque d'entraîner une décharge électrique

et de provoquer des blessures graves, voire

mortelles.

IMPORTANT: Make sure to plug any option

card into its connector properly (pins

aligned).

IMPORTANT: Avoid hot plug-in or the

removal of any option card from the FX

Supervisory Controllers (or other accessory

module). This means you must first remove

power from the unit.

Mounting

Mounting the RS-232 Card onto the FX

Supervisory Controllers

Mount the RS-232 card in either of the option

card slots on the FX Supervisory Controllers,

as available.

To mount the RS-232 card onto the

FX Supervisory Controllers:

1. If a station is running, stop it using the

platform Application Director view.

2. Remove power from FX Supervisory

Controller.

3. Remove the FX Supervisory Controller

cover. To do this, press in the four tabs on

both ends of the FX Supervisory Controller

and lift off the cover.

Note: If accessory modules are plugged

into the FX Supervisory Controllers, you

may need to slide them away from the unit

to access the cover tabs.

4. If the battery and bracket is installed,

remove it by taking out the four screws

holding the bracket in place. Set the

screws aside for later.

5. Unplug the battery from the connector on

the FX Supervisory Controllers (Figure 2).

FXSupervisory

Controll er

Figure 2: Removing the Battery Assembly

6. Remove the blanking end plate for the slot

you are installing the option card into.

Retain the blanking end plate in case you

want to remove the option card at a later

date.

7. Carefully insert the pins of the RS-232

card into the socket of the appropriate

option card slot. The mounting holes on

the RS-232 card should line up with the

standoffs on the FX Supervisory

FX Supervisory Controllers RS-232 Card Installation Instructions 3

Controllers. If they do not line up, the

connector is not properly aligned.

8. Press until the RS-232 card is completely

seated.

9. Place the custom end plate that came with

the RS-232 card over its connector

(Figure 3).

Figure 3: Inserting the RS-232 Card

10. If you are installing or replacing the

battery or bracket, plug the battery cable

into the battery connector on the FX

Supervisory Controller. See Figure 2 for

the location.

11. Set the battery and bracket assembly back

over the option card slots, with the

mounting holes aligned with the standoffs.

12. Place the four screws through the battery

bracket, end plates, and into the standoffs

on the FX Supervisory Controller. Hand

tighten these screws with a screwdriver.

Figure 4: Refastening the Screws

13. Replace the FX Supervisory Controller

cover. If accessory modules were

unplugged, plug them back into the FX

Supervisory Controller as before, and

secure.

14. Restore power to the controller and verify

normal operation.

Wiring

The RS-232 card uses standard DB-9M plug

and pinouts (it is identical to the RS-232 port

on the FX Supervisory Controller base). To

connect the FX Supervisory Controller RS-232

card with a Data Terminal Equipment (DTE)

device, use a null modem cable with DB9

connector.

Table 1: RS-232 Card Port Assignments

FX20/FX30E/FX60/FX60E FX70

Up to 2 RS-232 cards supported Up to 2 RS-232 cards supported

Option Slot 1 Option Slot 2 Option Slot 1 Option Slot 2

RS-232 =

COM3 RS-232 = COM4 RS-232 = COM5 RS-232 = COM6

RS-485 =

COM3, COM4 RS-232 = COM5 RS-485 = COM5,

COM6 RS-232 = COM7

LON = LON1 RS-232 = COM3 LON = LON1 RS-232 = COM5

Wireless TEC =

COM1 RS-232 = COM3 NA NA

Sedona =

COM3 RS-232 = COM4 Sedona = COM5 RS-232 = COM6

Modem =

COM1 RS-232 = COM3 Modem = COM3 RS-232 = COM5

GPRS = COM3,

COM4 RS-232 = COM5 GPRS = COM5,

COM6 RS-232 = COM7

4FX Supervisory Controllers RS-232 Card Installation Instructions

Table 2: COM Assignment for RS-232 Card in Option Slot 2

Pinout References Signal DB-9 Plug Pin

DB-9 Plug (Male)

DCD Data carrier

detect 1

RXD Receive data 2

TXD Transmit data 3

DTR Data terminal

ready 4

GND Ground 5

DSR Data set ready 6

RTS Request to send 7

CTS Clear to send 8

Repair Information

If the RS-232 option card fails to operate

within its specifications, replace the unit.

For a replacement option card, contact the

nearest Johnson Controls® representative.

Operation

LEDs

Two LEDs are visible on the top of the

RS-232 option card when the cover is

removed from the FX Supervisory

Controller. These LEDs are as follows:

RX (green): Receive. Indicates that

the FX Supervisory Controller is receiving

data from a device.

TX (yellow): Transmit. Indicates that

the FX Supervisory Controller is

transmitting a message to a device.

Building Efficiency

507 E. Michigan Street, Milwaukee, WI 53202

Johnson Controls® is a registered trademark of Johnson Controls, Inc.

Autres manuels pour Facility Explorer FX20

Ce manuel convient aux modèles suivants

Autres manuels Johnson Controls Unité de contrôle

Johnson Controls

Johnson Controls Tyco DV-5a Series Manuel utilisateur

Johnson Controls

Johnson Controls System 450 Series Manuel utilisateur

Johnson Controls

Johnson Controls P352PN-2 Manuel utilisateur

Johnson Controls

Johnson Controls GM 20 Series Manuel utilisateur

Johnson Controls

Johnson Controls Tyco DV-5a Series Manuel utilisateur

Johnson Controls

Johnson Controls Penn System 350 S350P Manuel utilisateur

Johnson Controls

Johnson Controls VMA 1410 Guide d'installation

Johnson Controls

Johnson Controls MS-IOM3723 Manuel utilisateur

Johnson Controls

Johnson Controls Tyco DV-5a Series Manuel utilisateur

Johnson Controls

Johnson Controls IOM3731 Manuel utilisateur

Johnson Controls

Johnson Controls VP1000 Series Manuel utilisateur

Johnson Controls

Johnson Controls S1-TTSCC01 Manuel utilisateur

Johnson Controls

Johnson Controls S1-TTSCC Manuel utilisateur

Johnson Controls

Johnson Controls Tyco DV-5a Series Manuel utilisateur

Johnson Controls

Johnson Controls Tyco RV-1A Manuel utilisateur

Johnson Controls

Johnson Controls METASYS NU-XBN101-0 Manuel utilisateur

Johnson Controls

Johnson Controls VP140 L Series Manuel utilisateur

Johnson Controls

Johnson Controls F4-XPM Series Manuel utilisateur

Johnson Controls

Johnson Controls VP101DBB Manuel utilisateur

Johnson Controls

Johnson Controls S1-TTSCC01 Guide de démarrage rapide

Johnson Controls

Johnson Controls VG7000 Series Manuel utilisateur

Johnson Controls

Johnson Controls GS-20 Series Manuel utilisateur

Johnson Controls

Johnson Controls V43 Series Manuel

Johnson Controls

Johnson Controls S300 Series Instructions de montage

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur