Johnson Controls S1-TTSCC01 Manuel utilisateur

Johnson Controls Unitary Products 542933-UIM-D-0513

INSTALLATION MANUAL

TOUCH SCREEN COMMUNICATING CONTROL

MODELS: S1-TTSCC01

LIST OF SECTIONS

GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

MOUNTING THE TOUCH SCREEN COMMUNICATING CONTROL . . . . . . . . . . . . . . . . . . . 4

REMOVING CONTROL MOUNTING BACK PLATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

WIRING COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

WIRING REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

SYSTEM WIRING OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

HUMIDIFIER CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

INITIAL POWER-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

POWER-UP SEQUENCE (SYSTEM MASTER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

ENTERING SERVICE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

SERVICE MODE ON MASTER CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

NAVIGATING SERVICE MODE: MASTER CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

FORCED OPERATION: MASTER CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

SERVICE TOOL SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

542933-UIM-D-0513

2 Johnson Controls Unitary Products

SECTION I: GENERAL

The Touch Screen Communicating Control is designed to manage communicating system compo-

nents (including: heat pumps, air conditioners, air handlers and furnaces). In general, these compo-

nents are the variable speed modulating furnace, 2-stage variable speed ECM furnace and variable

speed air handler, premium 15 and 18 SEER air conditioners or premium 13, 15 and 18 SEER heat

pumps.

While the communicating system has been designed for easy installation, this document will pro-

vide the installer with a more detailed explanation of installation process.

SECTION II: SAFETY CONSIDERATIONS

This is a safety alert symbol. When you see this symbol on labels or in manuals, be alert to

the potential for personal injury and equipment damage.

Understand and pay particular attention to the signal words DANGER, WARNING, and CAUTION.

DANGER indicates an imminently hazardous situation, which, if not avoided, will result in death

or serious injury.

WARNING indicates a potentially hazardous situation, which, if not avoided, could result in death

or serious injury.

CAUTION indicates a potentially hazardous situation, which, if not avoided may result in minor or

moderate injury. It is also used to alert against unsafe practices and hazards involving only prop-

erty damage.

INSPECTION

The following list details the parts included in this kit. Examine the kit to insure that all parts are

included.

LIMITATIONS

The Touch Screen Communicating Control’s primary function is to command a system containing

communicating product.

Exceptions to this rule are:

• Installing a communicating variable speed modulating furnace with a non-communicating air

conditioner. In this case the variable speed modulating furnace relays 24 VAC outputs to the

non-communicating air conditioner (per communicated commands by the Touch Screen

Communicating Control).

• Installing communicating controls in non-communicating UPG products.

• Installing Communicating Interface Control (which converts communicating commands into

24VAC outputs).

Item QTY. Description

1 1 Touch Screen Communicating Control

2 1 Communicating Plug Harness

3 1 Screw and Anchor Hardware bag

4 1 USB Adapter

5 1 Installation Instructions

6 1 Owner's Manual

7 1 Quick Help Document

8 1 Warranty Certificate

9 1 Warranty Registration Card

542933-UIM-D-0513

Johnson Controls Unitary Products 3

SECTION III: INSTALLATION

The intention of this document is to ensure proper connection/setup of the various communicating

system components. These instructions should be used in conjunction with the instructions pro-

vided with indoor, outdoor and accessory equipment of which the Touch Screen Communicating

Control will command.

This installation instruction contains (in part) setup, operation, and troubleshooting of the UPG Com-

municating System.

The Touch Screen Communicating Control will engage the installer with special screen prompts and

introduce settings to simplify and provide a path through the initial start up of the system.

When Installing this Product...

1. Read all instructions carefully before beginning installation. Failure to follow these instructions

can create hazardous situations or damage the product.

2. Make certain the product is suitable for your application by checking all ratings on the product

and in the instruction provided.

3. Installer must be a trained, experienced service technician.

LOCATION

Install the Touch Screen Communicating Control at or around 5 ft. (1.5m) above the floor in an area

with good circulation of room temperature. See Figure 1.

Do not install the Touch Screen Communicating Control where it can be affected by:

• Drafts or dead spots behind doors and in corners

• Hot or cold air from ducts

• Radiant heat from sun or appliances

• Concealed pipes and chimneys

• Unconditioned areas such as an outside wall

FIGURE 1: Control Location

YES

5 FEET

(1.5 METERS)

542933-UIM-D-0513

4 Johnson Controls Unitary Products

MOUNTING THE TOUCH SCREEN COMMUNICATING CONTROL

For most installations, mounting Touch Screen Communicating Control can be done following some

very basic installation steps outlined below. However, there may be some cases where the installer

is not able to penetrate the wall where mounting the Touch Screen Communicating Control, or there

may be an application where the thermostat/control being replaced has left a larger hole than

needed for installation of this control. For these and other applications, (including installation with a

vertical j-box) an installer can obtain a Decorative/Mounting Kit (S1-02815909000).

1. If an existing thermostat or control is being replaced:

a. Remove existing control from wall.

b. Disconnect wires from existing control.

c. Properly discard or recycle old control.

2. Mark on the wall where the Touch Screen Communicating Control will be mounted (standard

height is 5 feet from the floor).

3. Cut a 2” x 2” square hole with the bottom of the square at the mark.

4. Using the mounting back plate as a template, mark the screw holes on the surface where

mounting the Touch Screen Communicating Control. Use a level to insure proper installation.

Voltage Hazard: Live wires can cause electrical shock or equipment damage. Disconnect power

before beginning installation.

Mercury is a hazardous substance, if existing thermostat or control contains any mercury, it

MUST be disposed of properly. The Touch Screen Communicating Control does not contain mer-

cury.

If an existing thermostat was in place, it may be ideal to use the same location for the Touch

Screen Communicating Control.

Make sure that the hole is cut so that the Touch Screen Communicating Control can be leveled

when mounted. See Figure 2 for more detailed mounting information.

NOTICE

542933-UIM-D-0513

Johnson Controls Unitary Products 5

5. Remove mounting back plate.

6. Drill holes (3/16” in diameter) in the marked area to accommodate the anchors (provided in the

kit).

7. Place anchors in the pre-drilled holes. Be sure that the anchors are fully inserted.

8. Pull low voltage wires through the mounting back plate as shown in Figure 3.

9. Connect low voltage wires as instructed in the wiring section of this document.

10.Screw the wired mounting back plate to the wall using the screws provided in the kit.

11. Align the terminal screw block with the pins on the back of the Touch Screen Communicating

Control and snap it to the mounting back plate.

REMOVING CONTROL MOUNTING BACK PLATE

Gently remove by tilting up to release the bottom of the Touch Screen Communicating Control and

then pull out/down to completely remove.

FIGURE 2: Mounting Back Plate Dimensions

FIGURE 3: Wires Pulled Through Mounting Back Plate

Fastening the wires in the terminal block before attaching the back plate to the wall will ultimately

ease the installation of the wire. Once on the wall, the terminal block has limited accessibility.

3-1/4”

2”

5/8”

3/16”

1”

5/8”

542933-UIM-D-0513

6 Johnson Controls Unitary Products

SECTION IV: WIRING COMMUNICATION

All wiring must comply with local electrical codes and ordinances. Refer to Table 1 for terminal des-

ignations.

WIRING REQUIREMENTS

Standard 18 awg thermostat wires can be used to connect the communicating system.

Special (shielded) cable is not typically required. As with all communicating devices, it is a good

idea to keep wiring at least one foot away from large inductive loads. Examples of large inductive

loads include: electronic air cleaners, motors, etc. If these wiring practices are ignored, it may intro-

duce electrical interference (noise) which can cause erratic system operation.

SYSTEM WIRING OVERVIEW

The system is connected by four wires. Two of the wires are used to bring power into the individual

controls (R and C) and two of the wires are used for serial communication (A+ and B-). The plug/

harness that is provided in the kit should be used on the outdoor control.

Each Touch Screen Communicating Control Kit is equipped with a Communicating Plug Harness

(Fig. 5). This wire harness should be used for the wiring of the outdoor unit.

TABLE 1:

Terminal Designations

Signal Definition Label

Data Non-inverted signal A (+)

Low voltage power hot 24 VAC (Hot) R

Low voltage power common and data

ground 24 VAC (Common) C

Data Inverted signal B (-)

There may be installation applications where large inductive loads cannot be avoided. In these

cases shielded wire would be desired to ensure proper system functionality.

The communicating system requires 4 wires to operate. If installing a communicating system, be

sure to supply at least 4 wires to each unit/control. Below is a simple diagram showing the ideal

wiring path.

NOTICE

542933-UIM-D-0513

Johnson Controls Unitary Products 7

FIGURE 4: High Level Wiring Path

FIGURE 5: Communicating Plug Harness

FIGURE 6: Wiring Diagram (Fully communicating system components)

ARCB

COMM.COMM.

A - GREEN WIRE

R - RED WIRE

C - BLACK WIRE

B - BLUE (WHITE WIRE)

ARCB

ARCB ARCB

WHITE (B)

BLACK (C)

RED (R)

GREEN (A)

Touch Screen

Communicating Control

VS Air Handler/Furnace

Communicating Control

Air Conditioner/Heat Pump

Communicating Control

A+

B-

A+

GND

B-

A+

B-

542933-UIM-D-0513

8 Johnson Controls Unitary Products

Touch Screen Communicating Control Wiring

1. Turn off all power to equipment.

2. Loosen the screws in the terminal block of the mounting back plate.

3. Match and connect thermostat wires to proper terminals on Touch Screen Communicating Con-

trol mounting back plate.

4. Push any excess wire back into the wall.

5. Once wires are secured, the mounting back plate can be placed on the wall as previously out-

lined.

FIGURE 7: Wiring Diagram Communicating Furnace, Non-Communicating AC

ELECTRICAL OPERATION HAZARD

Failure to follow this warning could result in personal injury, death, or equipment damage.

Before installing, modifying, or servicing system, the main electrical disconnect switch must be in

the OFF position. There may be more than 1 disconnect switch. Lock out and tag switch with a

suitable warning label.

Plugging the hole in the wall with nonflammable insulation can help prevent drafts from adversely

affecting temperature control.

A+

B-

A+

GND

B-

COMP

DHUM

Y/Y2

Touch Screen

Communicating Control

Modulating Furnace

Communicating Control

Non-Communicating

Air Conditioner

NOTICE

542933-UIM-D-0513

Johnson Controls Unitary Products 9

Outdoor Control Wiring

A new communicating heat pump or air conditioner (denoted by a “-C” in the model number) will

have two communicating plug terminals (as shown in Figure 8).

1. Disconnect all power from system (including high and low voltage).

2. Remove factory installed low voltage harness.

3. Plug the communication harness provided in the Touch Screen Communicating Control Kit (S1-

TTSCC01) into the communication port on the outdoor control.

FIGURE 8: Outdoor Communicating Terminals

ELECTRICAL OPERATION HAZARD

Failure to follow this warning could result in personal injury, death, or equipment damage.

Before installing, modifying, or servicing system, the main electrical disconnect switch must be in

the OFF position. There may be more than 1 disconnect switch. Lock out and tag switch with a

suitable warning label.

COMMUNICATING TERMINALS

COMMUNICATING

AC CONTROL

COMMUNICATING

HEAT PUMP

CONTROL

542933-UIM-D-0513

10 Johnson Controls Unitary Products

4. Wire nut thermostat wire (from the indoor control) to the communication harness wires.

5. Set the wires which are now connected (with wire nuts) into the Junction Box of the control

housing (pictured below).

6. Set the appropriate jumper settings to insure proper control functionality (See table below).

When connecting the loose ends of the wire harness, be sure to note color for each of the four

wires (A+, R, C, B-).

FIGURE 9: Outdoor Control Housing

Unit Control Jumpers which must be set

Heat Pump Fossil Fuel

Hot Heat Pump

Air Conditioner No Jumpers to set

Jumpers listed here are required and if set incorrectly will flag an error upon installation. While the

other jumpers can be set from the Touch Screen Communicating Control, it is good practice to ini-

tially set all jumpers at the respective control. This will avoid any confusion that may occur with

future service at the units.

For installation of a non-communicating outdoor unit with the Touch Screen Communicating Con-

trol, the installer should reference the indoor and outdoor unit installation instructions. If informa-

tion is not provided, there may be a need for a Communicating Interface Control Field Kit (S1-

33102953000).

NOTICE

COMMUNICATIONS

PORT

CONTROL BOARD

COMMUNICATIONS

HARNESS

JUNCTION

BOX

NOTICE

Autres manuels pour S1-TTSCC01

Table des matières

Autres manuels Johnson Controls Unité de contrôle

Johnson Controls

Johnson Controls H Series Manuel utilisateur

Johnson Controls

Johnson Controls M4-XPM Manuel utilisateur

Johnson Controls

Johnson Controls MS-IOU4710-0U Manuel utilisateur

Johnson Controls

Johnson Controls VP140 Manuel utilisateur

Johnson Controls

Johnson Controls Tyco RSV-1 Manuel utilisateur

Johnson Controls

Johnson Controls A19ZBC Series Manuel de service

Johnson Controls

Johnson Controls Tyco PRV-1A Manuel utilisateur

Johnson Controls

Johnson Controls System 350 Manuel de service

Johnson Controls

Johnson Controls tyco AMD-1 Manuel utilisateur

Johnson Controls

Johnson Controls Tyco TJPX0500003 Manuel utilisateur

Johnson Controls

Johnson Controls IOM1711 Manuel utilisateur

Johnson Controls

Johnson Controls Mercury P2000 CKM-MR16IN Manuel

Johnson Controls

Johnson Controls Penn A19K Series Manuel utilisateur

Johnson Controls

Johnson Controls Tyco DV-5a Series Manuel utilisateur

Johnson Controls

Johnson Controls VG8000V Series Manuel utilisateur

Johnson Controls

Johnson Controls VG7000 Series Manuel utilisateur

Johnson Controls

Johnson Controls Tyco DV-5a Series Manuel utilisateur

Johnson Controls

Johnson Controls S1-TTSCC Manuel utilisateur

Johnson Controls

Johnson Controls P352PN-2 Manuel utilisateur

Johnson Controls

Johnson Controls tyco AMD-2 Manuel utilisateur

Johnson Controls

Johnson Controls METASYS NU-XBN101-0 Manuel utilisateur

Johnson Controls

Johnson Controls VMA 1410 Guide d'installation

Johnson Controls

Johnson Controls Facility Explorer FX20 Manuel utilisateur

Johnson Controls

Johnson Controls MS-NCM4510-2 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur