Intermec EasyCoder PD4 Manuel utilisateur

EasyCoder®PD4/PD41/PD42

Thermal Printhead (200/300 dpi) Installation Instructions

These instructions tell you how to install a 200 dpi or 300 dpi thermal

printhead in an EasyCoder PD4/PD41/PD42 printer. The kit contains the

following:

• 200 dpi or 300 dpi thermal printhead

• Printhead adapter printed circuit board (PCB)

Required Tools

To install the interface board in your printer, you need these tools:

• Screwdriver, slotted

• Screwdriver, Phillips (with magnetic tip)

Installing the Thermal Printhead and the Adapter PCB

Before you begin installation, please acknowledge the following important

safety notes:

Make sure the printer has been turned off and

disconnected from the power supply before you

start installation.

Stellen Sie sicher, dass der Drucker abgeschaltet

und von der Stromversorgung abgetrennt wurde,

bevor Sie mit der Installation beginnen.

Take precautions against electrostatic discharge, for

example, by wearing grounded wrist straps.

To install the thermal printhead

1Turn off the printer and unplug the power cord.

2Open the side door of the printer.

3Raise the printhead by pulling out the printhead lever and turning it

counterclockwise a quarter of a turn.

4Remove any thermal transfer ribbon.

5Remove the old printhead by pulling it out toward the front of the

printer.

Steps 6-9 describe how to replace the printhead adapter PCB which is

necessary if you are changing to a printhead with different resolution (for

instance, going from 200 dpi to 300 dpi). If this is not the case, go to

Step 11.

Note: If you are using a PD4 printer, you cannot switch to a

printhead with a different resolution other than that which the

printer was designed for.

6Move the balance boxes to the center position, to facilitate the removal of

the adapter PCB.

7Use an appropriate tool, for example a slotted screwdriver, to carefully

pry the printhead cable connector loose from the adapter PCB.

8Remove the two screws that attach the adapter PCB to the printer.

Remove the adapter PCB.

9Attach the new adapter PCB with the two screws removed in Step 8.

10 Connect the printhead cable to the adapter PCB.

11 Insert the new printhead and connect it to the adapter PCB.

12 Adjust the position of the balance boxes so that they fit the width of your

media.

Worldwide Headquarters

6001 36th Avenue West

Everett, Washington 98203

U.S.A.

tel 425.348.2600

fax 425.355.9551

www.intermec.com

©

2007 Intermec Technologies

Corporation. All rights reserved.

13 Close the side door of the printer.

14 Plug in the power cord and turn the printer on.

EasyCoder PD4/PD41/PD42 Thermal Printhead (200/300dpi) Installation Instructions

*1-960658-02*

P/N 1-960658-02

Autres manuels pour EasyCoder PD4

5

Ce manuel convient aux modèles suivants

2

Table des matières

Autres manuels Intermec Accessoires pour imprimantes

Intermec

Intermec PB50 Manuel utilisateur

Intermec

Intermec EasyCoder PF4ci Manuel utilisateur

Intermec

Intermec EasyCoder F2 Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec EasyCoder PD41 Manuel utilisateur

Intermec

Intermec PM4I Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec CN3 Series Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec 4820 Guide de démarrage rapide

Intermec

Intermec EasyCoder 3400d Manuel utilisateur

Intermec

Intermec EasyCoder 501 E Manuel utilisateur

Intermec

Intermec EasyCoder PC4 Manuel utilisateur

Intermec

Intermec EasyCoder PD4 Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec PW50 Manuel utilisateur

Intermec

Intermec PW50 Manuel utilisateur

Intermec

Intermec EasyCoder 501 SA Manuel utilisateur

Intermec

Intermec Font Card Manuel utilisateur

Intermec

Intermec EasyCoder 601XP Manuel utilisateur

Intermec

Intermec 074788 Series Manuel utilisateur

Intermec

Intermec EasyCoder 501XP Manuel utilisateur

Intermec

Intermec EasyCoder 601XP Manuel utilisateur

Intermec

Intermec EasyCoder 201II Manuel utilisateur

Manuels Accessoires pour imprimantes populaires d'autres marques

Star Micronics

Star Micronics TSP800 Series Manuel utilisateur

REA

REA JET HR pro 2K Manuel utilisateur

HP

HP Laserjet,Color Laserjet 4si Manuel utilisateur

oliser

oliser MS 45 Manuel utilisateur

Roland

Roland DU2-64 Instructions et recettes

Xerox

Xerox EFI EXP6000 Manuel utilisateur

Canon

Canon Finisher-T1 Manuel utilisateur

Sharp

Sharp FO-1MK Manuel utilisateur

Labelmate

Labelmate PM-300 Manuel utilisateur

Epson

Epson T6248 Manuel d'utilisation

Epson

Epson OT-BZ20 Manuel utilisateur

Canon

Canon TonerRobot EP-27 Manuel utilisateur

Ricoh

Ricoh LCIT RT5100 Guide de démarrage rapide

GBC

GBC 16 Series Manuel utilisateur

Canon

Canon INNER 2-WAY TRAY-E1 Manuel d'utilisation et d'entretien

Develop

Develop SD-509 Manuel utilisateur

Kyocera

Kyocera KM-6230 Manuel

Triumph Adler

Triumph Adler DF-710 Manuel