Intermec EasyCoder PF2i Manuel utilisateur

Installation

Instructions

Label Taken

Sensor Kit

(for EasyCoder PF2i,

PF4i, and PF4i Com-

pact Industrial)

Intermec Printer AB

Idrottsvägen 10

P.O. Box 123

S-431 22 Mölndal

Sweden

Service support: +46 31 869500

The information contained herein is proprietary and is provided solely

for the purpose of allowing customers to operate and/or service Intermec

manufactured equipment and is not to be released, reproduced, or used

for any other purpose without written permission of Intermec.

Information and speciﬁcations in this manual are subject to change

without notice.

EasyCoder and Fingerprint are registered trademarks of Intermec Tech-

nologies Corp. The word Intermec and the Intermec logo are trademarks

of Intermec Technologies Corp.

Torx is a registered trademark of Camcar Division of Textron Inc.

Throughout this manual, trademarked names may be used. Rather than

put a trademark (™) symbol in every occurrence of a trademarked name,

we state that we are using the names only in an editorial fashion, and to

the beneﬁt of the trademark owner, with no intention of infringement.

Preface

Contents

Introduction ................................................................................. iv

Printer Firmware........................................................................... iv

Installation Kit.............................................................................. iv

1 Physical Installation

Installation Instructions .................................................................2

2 Controlling and Adjusting the LTS

Intermec Fingerprint v8.xx.............................................................6

IPL v2.xx .......................................................................................7

Label Taken Sensor Kit Installation Instructions iii

Preface

iv Label Taken Sensor Kit – Installation Instructions

Introduction

This Installation Instructions booklet describes how to install a label

taken sensor (LTS) in an EasyCoder PF2i, PF4i, or PF4i Compact Indus-

trial printer, how to adjust the sensitivity, and how to control it in either

Intermec Fingerprint or IPL.

The label taken sensor enables the printer’s ﬁrmware to detect if the

latest printed label (or similar) has been removed before starting to print

next label. It consists of a light-emitting diode (LED) and a photoelec-

tric sensor. The LED emits a narrow beam of light upwards towards the

media outfeed area. If the light is reﬂected back by a label, that has not

yet been removed, it will be detected by the sensor and a label-not-taken

condition is assumed. The theoretical point of detection is 20.7 mm

(0.81 in) outside the inner edge of the media path and immediately in

front of the tear bar.

This interface kit must only be physically installed by an

authorized service technician. Intermec assumes no respon-

sibility for personal injury or damage to the equipment if

the installation in performed by an unauthorized person.

Take precautions against electrostatic discharges, for

example by wearing grounded bracelets.

Printer Firmware

Intermec Fingerprint v8.00 (or later) or IPL v2.00 (or later).

Installation Kit

The Label Taken Sensor Kit contains:

•One sensor with cable and connector

•One bracket

•One #T10 Torx screw

•One Installation Instruction booklet

Tool requirements: #T10 and #T20 Torx screwdrivers.

Label Taken Sensor Kit Installation Instructions 1

1 Physical Installation

This chapter describes how to physically install the

Label Taken Sensor (LTS) kit in a PF2/4i-series

printer.

2 Label Taken Sensor Kit – Installation Instructions

Chapter 1 — Physical Installation

Installation Instructions

•Switch off the printer and disconnect the power cord.

•Disconnect all communication cables.

•Remove the bottom plate as follows.

The electronic compartment contains wires and compo-

nents with dangerous voltage (up to 380V). Make sure that

the printer is switched off and the power cord is discon-

nected before bottom plate is removed.

•Turn the printer upside down on a soft cloth or similar to avoid

scratches.

•Using a #T20 Torx screwdriver, remove the six screws indicated below

and lift away the bottom plate and right-hand door assembly.

Label Taken Sensor Kit Installation Instructions 3

Chapter 1 — Physical Installation

•Fit the sensor and bracket to the lug at the printer’s front while rout-

ing the cable between the two rails on the center section and through

the slot in the center section as illustrated below.

•Connect the LTS cable to J53 at the lower edge of the CPU board.

The connector is marked “LTS.”

•Put back the bottom plate.

•Put the printer back on its feet and connect the power cord and all

communication cables.

Mounting lug

Sensor

Bracket

#T10 Torx screw

Cable to J53

on CPU board

Center section

Label Taken Sensor Kit – Installation Instructions

Chapter 1 — Physical Installation

Label Taken Sensor Kit Installation Instructions 5

2 Control and Adjustment

This chapter describes how to control and adjust the

label taken sensor in printers running either Intermec

Fingerprint v8.00 (or later) or IPL v2.00 (or later).

6 Label Taken Sensor Kit – Installation Instructions

Chapter 2 — Control and Adjustment

Intermec Fingerprint

Controlling the LTS

The label taken sensor can be enabled using the instructions LTS& ON

and LTS&OFF respectively. The status of the LTS can be polled using

the function PRSTAT. See Intermec Fingerprint v8.00, Programmer’s

Reference Manual.

Adjusting the LTS

The sensitivity of the Label Taken Sensor (LTS) may need to be adjusted

according to the ambient light conditions and the reﬂective character-

istics of the back side of the media. The sensitivity can be adjusted in

the Setup Mode or by using setup ﬁles or setup strings (see Intermec

Fingerprint v8.xx, Programmer’s Reference Manual). There are no straps or

potentiometers for adjusting the LTS.

In the Setup Mode, the LTS setup options are only displayed if an

optional label taken sensor is installed in the printer. Also refer to the

User’s Guide, chapters “Setting Up the Printer”and “Setup Mode”for

instructions how to adjust the LTS.

•LTS Adjust:

Press <Enter>. A label is fed out. Remove the label and press <Enter>

again. A menu shows the sensitivity automatically selected by the ﬁrm-

ware and the range in which the LTS will work. Press <Enter> again

and you will proceed to the LTS Test menu.

•LTS Test:

Press <Enter>. A label is fed out. Remove the label and a new label

should be fed out automatically. Repeat until you are sure the LTS

works properly. Then press <Enter> to stop and exit.

•LTS Value:

Press <Enter>. You can enter a new value in the range indicated in the

LTS Adjust menu (see above). Min/max values are in the range 0-10.

Autres manuels pour EasyCoder PF2i

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Intermec Accessoires pour imprimantes

Intermec

Intermec EasyCoder 3400e Manuel utilisateur

Intermec

Intermec EasyCoder 4420 Manuel

Intermec

Intermec EasyCoder 201II Manuel du propriétaire

Intermec

Intermec CN3 Series Manuel utilisateur

Intermec

Intermec Font Card Manuel utilisateur

Intermec

Intermec 3400 Manuel utilisateur

Intermec

Intermec EasyCoder PD4 Manuel utilisateur

Intermec

Intermec EasyCoder 501 SA Manuel utilisateur

Intermec

Intermec EasyCoder 3400d Manuel utilisateur

Intermec

Intermec EasyCoder 601XP Manuel utilisateur

Intermec

Intermec PB50 Manuel utilisateur

Intermec

Intermec EasyCoder 4420 Manuel utilisateur

Intermec

Intermec EasyCoder F2 Manuel utilisateur

Intermec

Intermec 3600 Manuel utilisateur

Intermec

Intermec EasyCoder 101 Manuel

Intermec

Intermec EasyCoder 3400e Manuel utilisateur

Intermec

Intermec EasyCoder 501 SA Manuel utilisateur

Intermec

Intermec PM4I Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec EasyCoder PC4 Manuel utilisateur

Intermec

Intermec PM4I Manuel utilisateur

Intermec

Intermec EasyCoder 601XP Manuel utilisateur

Intermec

Intermec PM4I Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Manuels Accessoires pour imprimantes populaires d'autres marques

Star Micronics

Star Micronics TSP800 Series Manuel utilisateur

REA

REA JET HR pro 2K Manuel utilisateur

HP Laserjet,Color Laserjet 4si Manuel utilisateur

oliser

oliser MS 45 Manuel utilisateur

Roland

Roland DU2-64 Instructions et recettes

Xerox

Xerox EFI EXP6000 Manuel utilisateur

Canon

Canon Finisher-T1 Manuel utilisateur

Sharp

Sharp FO-1MK Manuel utilisateur

Labelmate

Labelmate PM-300 Manuel utilisateur

Epson

Epson T6248 Manuel d'utilisation

Epson

Epson OT-BZ20 Manuel utilisateur

Canon

Canon TonerRobot EP-27 Manuel utilisateur

Ricoh

Ricoh LCIT RT5100 Guide de démarrage rapide

GBC

GBC 16 Series Manuel utilisateur

Canon

Canon INNER 2-WAY TRAY-E1 Manuel d'utilisation et d'entretien

Develop

Develop SD-509 Manuel utilisateur

Kyocera

Kyocera KM-6230 Manuel

Triumph Adler

Triumph Adler DF-710 Manuel