Intermec EasyCoder 501 SA Manuel utilisateur

EasyCoder 501/601

Industrial Interface Kit

P/N 1-960343-02

Edition 2

September 1998

Installation Instructions

EasyCoder 501/601 – Installation Instructions

Note:

Illustrations show an EasyCoder 501.

The principles for fitting this optional

equipment in an EasyCoder 601 are

exactly the same.

INDUSTRIAL INTERFACE KIT

TheIndustrialInterfaceBoardaddsoneserialcommunicationport

("uart3")andoneconnectorwithfourINandfourOUTportstothe

standard serial communication port ("uart1:").

The IN/OUT ports provide an interface between the printer and

varioustypes ofexternal equipment,such asgates, conveyorbelts,

wrappers etc. The input and output signals can be read or initiated

bymeansofIntermecFingerprintinstructions.Therebytheprinter

can be used to control the external devices – or be controlled by

them – according to the program.

Theprinter'sfirmwaredetectswhenanIndustrialInterfaceBoardis

installed and adds communication and buffer setup options for the

communication port "uart3:".

Whenan IndustrialInterfaceBoardisfitted,thefollowing typesof

interfaces become available:

"uart1:"

Fittedon printer's CPUboard.

RS232C Standard. Selectedby strap.

RS422 or20 mA CL Option. Additional circuits required.

"uart3:"

Fittedon Industrial InterfaceBoard.

RS232C

IN/OUT connector

Fittedon Industrial InterfaceBoard.

4input channels The software can read the status of four different

inputsignals.

4output channels Thesoftwarecan setfourdifferentsignalstoeither

openor closedcontact and also read theirstatus.

The Industrial Interface Kit consists of:

• 1 Interface board assy.

• 2 Screws MRX-Z 3 ×6 FZB (not intended for EasyCoder 501/

601)

• This Installation Instruction

Introduction

EasyCoder 501/601

Industrial Interface Kit

Installation Instructions

Edition 2, September 1998

Part No. 1-960343-02

230V

"uart1:"

IN/OUT ports

"uart3:"

EasyCoder 501/601 – Installation Instructions

The only tool required is a Torx #T10 screwdriver.

❑Turn off the power and remove the power cord.

❑Remove the communication cable from communication port

"uart1:".

❑Open the right hand door.

❑Remove the eight Torx screws that hold the cover over the left

part of the printer (see illustration below).

❑Remove the cover.

Continued!

INDUSTRIAL INTERFACE KIT, cont'd.

Step-by-Step Installation

Instructions

Communication

Port "uart1:"

230V

Power

Switch

Power Cord

Receptacle

Screws (4x)

Cover

Screws (4x)

EasyCoder 501/601 – Installation Instructions

❑Remove the existing cover plate.

❑Make sure that the CPU board is strapped and equipped for the

desired type of communication on "uart1:" (see the EasyCoder

501 or EasyCoder 601 Technical Manual). Once the interface

boardhasbeenfitted,itwill bedifficulttoaccesstherearpartof

the CPU board.

❑Fit the required straps on the Industrial Interface Board as

described on page 5.

❑Connect the cable from the interface board to connector P-4 at

the bottom rear corner of the CPU board. Be careful so the

interface board and the CPU board do not come in contact with

eachother,whichpossiblymaycausedamageorshort-circuiting.

❑Fit the interface board assembly to the printer's rear plate from

theinsideasillustratedbelowusingthesamescrewsthatheldthe

removed cover plate.

Continued!

INDUSTRIAL INTERFACE KIT, cont'd.

Step-by-Step Installation

Instructions, cont'd.

P2P6P7P8

123123123123

Industrial

Interface Board

Connect to P-4

on CPU Board

Rear Plate

Screw

Female DB15

I/O Connector

Female DB25

Connector

"uart3:"

EasyCoder 501/601 – Installation Instructions

INDUSTRIAL INTERFACE KIT, cont'd.

Step-by-Step Installation

Instructions, cont'd. ❑Reassemble the printer in reverse order.

❑Connect the communication cables to their respective connec-

tors. Please refer to page 6 for pinout descriptions.

❑Connect the power cord and turn on the power.

❑Ifyouintendtousethecommunicationport"uart3:"(RS232C),

set up its communication and buffer parameters as described in

the EasyCoder 501 or EasyCoder 601 Technical Manual.

230V

"uart1:"

"uart3:"

IN/OUT

Ports

Industrial Interface

Board Assy.

EasyCoder 501/601 – Installation Instructions

INDUSTRIAL INTERFACE KIT, cont'd.

Straps

Communication Port "uart3:"

RS 232C:

There are no straps for controlling the RS 232C interface on

"uart3:".

External +5V:

External +5V ( max. 200 mA) can be made available on pin 16 by

fitting a strap on P-1.

Be careful not to enable this option unintentionally, which may

cause harm to the connected terminal, computer or other device.

In/Out Connector

In/Out port 201-204:

One relay for each port switches the OUT signal to open or closed

as PORTOUT ON/OFF statements are executed in the program.

Four straps, P-2, P-6, P-7 and P-8, control the relation between

relay and output signal on output ports 201–204 respectively:

PORTOUT stmt Strap between pins OUT signal

PORTOUT(<nexp>) ON 1–2(upper position) Open

PORTOUT(<nexp>) ON 2–3(lower position) Closed

PORTOUT(<nexp>) OFF 1–2(upper position) Closed

PORTOUT(<nexp>) OFF 2–3(lower position) Open

P6P7P8

123123123123

"uart3:"

I/O connector

P-6

P-8

P-1

P-2

P-7

EasyCoder 501/601 – Installation Instructions

Pin "uart3:" Remarks Pin In/Out connector Remarks

DB25female DB15 female

1 GNDC Cableshield 1 OUT201 Seeexample onnext page

2 TXDB Transmitteddata from printer 2 OUT201

3 RXDB Receiveddata to printer 3 OUT202

4 RTSB RTSfrom printer 4 OUT202

5 CTSB CTSto printer 5 OUT203

6 DRSB DSRto printer 6 OUT203

7 GNDI Signal ground 7 OUT204

8 – notused 8 OUT204

9 – notused 9 IN101 See example on next page

10 – notused 10 IN101

11 – notused 11 IN102

12 – notused 12 IN102

13 – notused 13 IN103

14 – notused 14 IN104

15 – notused 15 IN103/104

16 +5VEXT +5V max200 mA*

17 – notused

18 – notused

19 – notused

20 DTRB DTRpemanently high

21 – notused

22 – notused

23 – notused

24 – notused

25 – notused

*/.If strapfitted on P-1

INDUSTRIAL INTERFACE KIT, cont'd.

Connector Configuration "uart3:" is a DB25 female connector.

The In/Out connector is a DB15 female connector.

The mounting holes are connected to chassis ground.

OUT signals are controlled by means of

PORTOUT (<nexp>) ON|OFF statements.

IN and OUT signals are read by means of

PORTIN (<nexp>) functions.

AlsoseeIntermecFingerprint6.13Programmer's

Manual.

EasyCoder 501/601 – Installation Instructions

INDUSTRIAL INTERFACE KIT, cont'd.

Connector Configuration,

cont'd.

IN1 9

P-3

TIL193B R5 R6

C10

Example of an IN port

Signal Min. Typical Max.

Input Voltage High 10V 24V 40V

Input Voltage Low -1V 0V 1V

Example of an OUT port

+5V

P-3

REL1

OUT1

P-2

Max AC Load Breaking Capacity

Max. DC Load Breaking Capacity

0.5

0.1

10 20 30 40 50 100

DC Voltage (VDC)

a: resistive load

b: inductive load L/R=20 ms

DC current (A)

Current max. 1 A

Switching power max. 100VA AC

Switching voltage max. 100V AC

EasyCoder 501/601 – Installation Instructions

Informationinthismanualissubjecttochangewithoutpriornoticeanddoesnotrepresentacommitment

on the part of Intermec Printer AB.

EasyCoder and Fingerprint are registered trademarks of Intemec Technologies Corp.

Torx is a registered trademark of Camcar Division of Textron Inc.

NOTES

Autres manuels pour EasyCoder 501 SA

Ce manuel convient aux modèles suivants

Autres manuels Intermec Accessoires pour imprimantes

Intermec

Intermec EasyCoder 501 SA Manuel utilisateur

Intermec

Intermec EasyCoder 501XP Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec PM4I Manuel utilisateur

Intermec

Intermec EasyCoder 601XP Manuel utilisateur

Intermec

Intermec EasyCoder F4 Manuel utilisateur

Intermec

Intermec EasyCoder 101 Manuel

Intermec

Intermec EasyCoder 3400e Manuel utilisateur

Intermec

Intermec 3400 Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec PB42 Manuel

Intermec

Intermec EasyCoder F2 Manuel utilisateur

Intermec

Intermec 4630 Manuel utilisateur

Intermec

Intermec EasyCoder 501XP Manuel utilisateur

Intermec

Intermec CN3 Series Manuel utilisateur

Intermec

Intermec EasyCoder 501 SA Manuel utilisateur

Intermec

Intermec EasyCoder PD41 Manuel utilisateur

Intermec

Intermec EasyCoder 601XP Manuel utilisateur

Intermec

Intermec PB50 Manuel utilisateur

Intermec

Intermec 825-192-001 Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec Font Card Manuel utilisateur

Intermec

Intermec EasyCoder F4 Manuel utilisateur

Intermec

Intermec EasyCoder 3400d Manuel utilisateur

Manuels Accessoires pour imprimantes populaires d'autres marques

Star Micronics

Star Micronics TSP800 Series Manuel utilisateur

REA

REA JET HR pro 2K Manuel utilisateur

HP Laserjet,Color Laserjet 4si Manuel utilisateur

oliser

oliser MS 45 Manuel utilisateur

Roland

Roland DU2-64 Instructions et recettes

Xerox

Xerox EFI EXP6000 Manuel utilisateur

Canon

Canon Finisher-T1 Manuel utilisateur

Sharp

Sharp FO-1MK Manuel utilisateur

Labelmate

Labelmate PM-300 Manuel utilisateur

Epson

Epson T6248 Manuel d'utilisation

Epson

Epson OT-BZ20 Manuel utilisateur

Canon

Canon TonerRobot EP-27 Manuel utilisateur

Ricoh

Ricoh LCIT RT5100 Guide de démarrage rapide

GBC

GBC 16 Series Manuel utilisateur

Canon

Canon INNER 2-WAY TRAY-E1 Manuel d'utilisation et d'entretien

Develop

Develop SD-509 Manuel utilisateur

Kyocera

Kyocera KM-6230 Manuel

Triumph Adler

Triumph Adler DF-710 Manuel