Intermec EasyCoder 501 SA Manuel utilisateur

EasyCoder 501/601

Sensor Kit

P/N 1-960411-02

Edition 3

September 1998

Installation Instructions

EasyCoder 501/601 – Installation Instructions

SENSOR KIT

Intermecoffersakitcontainingtwosensors,thatdetecttherotation

of the paper supply spool and the ribbon unwind shaft and update

two counters, one for each sensor. By means of custom-made

applicationprograms,thecounterscanbereadandusedforindicate

paper-lowandribbon-low conditions (asopposedto out-of-paper-

out and out-of-ribbon conditions, which are supported by the

standard error handling). See SYSVAR system array in Intermec

Fingerprint 6.13 Reference Manual1.

The Sensor Kit is available for the following printer models:

Model Ribbon Low Sensor Paper Low Sensor

EasyCoder 501 E yes yes

EasyCoder 501 SA yes yes

EasyCoder 601 S yes no

EasyCoder 601 E yes yes

Thesensorkitconsistsoftwophoto-electric sensors and two #T10

Torx screws.

The sensors require no regular cleaning. However, should any

malfunctionbedetected,youmaytrytoblowthesensorclearfrom

dust or paper residue before replacing it.

The sensitivity of these sensors cannot be adjusted.

Introduction

Ribbon Low Sensor Paper Low Sensor

The illustration shows the sensor kit fitted on an EasyCoder 501 E

printer.

1/. The system variable SYSVAR reads

the counters as follows:

SYSVAR (12) reads the paper counter

SYSVAR(13)readstheribboncounter

EasyCoder 501/601

Sensor Kit

Installation Instructions

Edition 3, September 1998

Part No. 1-960411-02

EasyCoder 501/601 – Installation Instructions

SENSOR KIT, cont'd.

Installation

Ribbon Low Sensor

• Open the right hand door.

• Turn off the power and remove the left-hand cover.

• Fromthe papercompartmentside,inserttheconnectorandcable

through the square hole in the centre-line wall.

• Insertthesensorunderthecodediskoftheribbonunwindunitso

the disc will run in the U-shaped slot between the receiver and

transmitter.

• Attach the sensor to the centre-line wall by means of one #T10

Torx screw. Check that the code disc can rotate freely.

• ConnectthecabletoconnectorP-605atthetopoftheCPUboard

(marked ➀).

• Continue by fitting the paper low sensor.

Paper Low Sensor

• Remove the three #T20 Torx screws holding the large crescent-

shapedguideplatethatsurroundsthepapersupply unit. Remove

the guide plate.

• Fit the sensor under the code disc of the upper supply unit using

the same method as with the ribbon low sensor.

• ConnectthecabletoconnectorP-602atthetopoftheCPUboard

(marked ➁).

• Fit back the guide plate and the left-hand cover.

Note!

The ribbon unwind unit and the paper

supply unit are shown dismounted in

the drawing only to improve visibility.

In reality, the only part that requires

dismounting is the guide plate.

Guide Plate

(remove)

Ribbon Unwind Unit

(do not remove) Paper Supply Unit

(do not remove)

Sensor

#T10 Torx screw

#T20 Torx screw (3x)

Sensor

#T10 Torx screw

Autres manuels pour EasyCoder 501 SA

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Intermec Accessoires pour imprimantes

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec EasyCoder 601XP Manuel utilisateur

Intermec

Intermec 4820 Guide de démarrage rapide

Intermec

Intermec PW50 Manuel utilisateur

Intermec

Intermec PA30 Manuel utilisateur

Intermec

Intermec EasyCoder 201II Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec ESim v4.20 Manuel utilisateur

Intermec

Intermec EasyCoder F2 Manuel utilisateur

Intermec

Intermec EasyCoder 501 SA Manuel utilisateur

Intermec

Intermec PB42 Manuel

Intermec

Intermec EasyCoder F4 Manuel utilisateur

Intermec

Intermec 3240 Manuel utilisateur

Intermec

Intermec PC43t Manuel utilisateur

Intermec

Intermec EasyCoder PF4ci Manuel utilisateur

Intermec

Intermec EasyCoder 101 Manuel

Intermec

Intermec EasyCoder PF4i Manuel utilisateur

Intermec

Intermec UBI EasyCoder 601 E Mode d’emploi

Intermec

Intermec EasyCoder F2 Manuel utilisateur

Intermec

Intermec PB50 Manuel utilisateur

Intermec

Intermec EasyCoder 501 E Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec EasyCoder 501 SA Manuel utilisateur

Intermec

Intermec EasyCoder PD41 Manuel utilisateur

Manuels Accessoires pour imprimantes populaires d'autres marques

Star Micronics

Star Micronics TSP800 Series Manuel utilisateur

REA

REA JET HR pro 2K Manuel utilisateur

HP Laserjet,Color Laserjet 4si Manuel utilisateur

oliser

oliser MS 45 Manuel utilisateur

Roland

Roland DU2-64 Instructions et recettes

Xerox

Xerox EFI EXP6000 Manuel utilisateur

Canon

Canon Finisher-T1 Manuel utilisateur

Sharp

Sharp FO-1MK Manuel utilisateur

Labelmate

Labelmate PM-300 Manuel utilisateur

Epson

Epson T6248 Manuel d'utilisation

Epson

Epson OT-BZ20 Manuel utilisateur

Canon

Canon TonerRobot EP-27 Manuel utilisateur

Ricoh

Ricoh LCIT RT5100 Guide de démarrage rapide

GBC

GBC 16 Series Manuel utilisateur

Canon

Canon INNER 2-WAY TRAY-E1 Manuel d'utilisation et d'entretien

Develop

Develop SD-509 Manuel utilisateur

Kyocera

Kyocera KM-6230 Manuel

Triumph Adler

Triumph Adler DF-710 Manuel