Intermec 3240 Manuel utilisateur
Centronics Parallel I/O Card
P/N 070872-001
Instruction Sheet
Intermec Technologies Corporation
6001 36th Avenue West
P.O. Box 4280
Everett, WA 98203-9280
U.S. service and technical support: 1.800.755.5505
U.S. media supplies ordering information: 1.800.227.9947
Canadian service and technical support: 1.800.688.7043
Canadian media supplies ordering information: 1.800.268.6936
Outside U.S. and Canada: Contact your local Intermec service supplier.
The information contained herein is proprietary and is provided solely for the purpose of allowing customers to
operate and/or service Intermec manufactured equipment and is not to be released, reproduced, or used for any
other purpose without written permission of Intermec.
Information and specifications in this manual are subject to change without notice.
2000 by Intermec Technologies Corporation
All Rights Reserved
The word Intermec, the Intermec logo, JANUS, IRL, Trakker Antares, Adara, EZBuilder, TE 2000, Data
Collection Browser, dcBrowser, Universal Access Point, UAP, Duratherm, EasyCoder, Precision Print,
PrintSet, Virtual Wedge, and CrossBar are either trademarks or registered trademarks of Intermec.
Throughout this manual, trademarked names may be used. Rather than put a trademark (or ) symbol in
every occurrence of a trademarked name, we state that we are using the names only in an editorial fashion, and
to the benefit of the trademark owner, with no intention of infringement.
Centronics Parallel I/O Instruction Sheet
3
Centronics Parallel I/O Card Instruction Sheet
The following instructions explain how to install an Intermec Centronics Parallel I/O
Card into Intermec 3240, 3400, 3440, 3600, and 4400 printers. This procedure is to be
performed by trained Intermec service personnel only.
Parts Provided:
•Centronics Parallel I/O Card
•Ribbon cable
•(2) Phillips screws
Tools Required:
•Phillips screwdriver
Warning
Electrical equipment is dangerous! Make sure the printer power switch is turned off
and the AC power cord is disconnected before opening the tower door or removing the
electronics cover. Working on live equipment can cause injury or death.
Avertissement
“Le matériel électrique peut être dangereux ! Assurez-vous que l’interrupteur
d’alimentation de l’imprimante est éteint et que le cordon d’alimentation est
débranché, avant d’ouvrir le couvercle du support d’imprimante. Travailler sur du
matériel sous-tension peut provoquer des blessures ou la mort.”
Centronics Parallel I/O Card Instruction Sheet
4
Install the Parallel I/O Card in the 3xxx Printer
Caution
Static electricity can damage electronic components as you handle them. Static-
sensitive electronic components are packaged in static protective bags. Before
opening the bag, touch it to the metal base of the printer to reduce static electricity.
Touch the metal base of the printer to reduce static electricity before installing the
parallel I/O card in the printer.
1. Turn off the printer power and remove the power cord.
2. Remove the media cover and the electronics cover from the printer.
3. Remove and discard the optional I/O board port cover from the rear of the printer
(see illustration). Retain the two port cover screws.
3XXI005.eps
Optional I/O
board port
Retain the
two screws
Optional
I/O board
port cover
Centronics Parallel I/O Card Instruction Sheet
5
4. Connect one end of the ribbon cable to the parallel I/O card.
Note: Both ends of the ribbon cable are keyed. Either end can be plugged into the
parallel I/O card or the main PCB.
5. With the component side of the parallel I/O card facing the interior of the printer,
secure the parallel I/O card to the optional I/O board port with the two port cover
screws.
3XXXI008.eps
J8
Parallel I/O
card
Optional I/O
board port
Main PCB
Ribbon
cable
Key
Ribbon
cable
Parallel I/O
card
Centronics Parallel I/O Card Instruction Sheet
6
6. Connect the free end of the ribbon cable to the appropriate connector (see the
following table) on the main PCB.
Printer Model Number I/O Connector
3240 J8
3400A and B J8
3400C and D J7
3440 J3
3600 J8
7. Reinstall and secure the media cover and electronics cover.
8. Reinstall the power cord.
9. Test that the printer recognizes the parallel I/O card by printing a hardware
configuration test label. See the printer user’s manual for instructions on printing a
hardware configuration test label. The following message should appear on the
configuration test label:
I/O Option Card: Centronix
Centronics Parallel I/O Card Instruction Sheet
7
Install the Parallel I/O Card in the 4400 Printer
Caution
Static electricity can damage electronic components as you handle them. Static-
sensitive electronic components are packaged in static protective bags. Before
opening the bag, touch it to the metal base of the printer to reduce static electricity.
Touch the metal base of the printer to reduce static electricity before installing the
parallel I/O card in the printer.
1. Turn off the printer power and remove the power cord.
2. Open the tower door by removing the three Phillips screws at the rear of the printer
(see illustration).
3. Remove and discard the port cover from the optional I/O board port. Retain the two
screws.
Tower door
Phillips screw
(3 places)
Optional I/O
board port
Port
cover
Phillips
screws
3XXXI001.eps
AC power
cord
Centronics Parallel I/O Card Instruction Sheet
8
4. Secure the parallel I/O card (Part No. 052713) to the optional I/O board port with
two Phillips screws. The components on the parallel I/O card must face toward the
interior of the printer.
5. Connect one end of the ribbon cable to the parallel I/O card.
Note: Both ends of the ribbon cable are keyed. Either end can be plugged into the
parallel I/O card or the main PCB.
6. Plug the parallel I/O cable (Part No. 053924) into J18 on the main PCB. Check that
all the cable connections (not shown) on the main PCB are secure.
7. Before closing the tower door, check all cable connections. All cables must be
carefully folded prior to securing the electronics door. Ensure that the keypad cable
is folded away from the encoder wheels of the TTR assembly. Close the tower door
and secure it with three Phillips screws.
8. Test that the printer recognizes the parallel I/O card by printing a hardware
configuration test label. For help, see the 4400 User's Manual (Part No. 058607).
The following message should appear on the configuration test label:
I/O Option Card: Centronix
Main PCB
J18
Parallel I/O card
Phillips screws
(2 places)
Tower door
Parallel I/O cable
Optional I/O
board port
3XXXI002.eps
Autres manuels pour 3240
7
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels Intermec Accessoires pour imprimantes
Intermec
Intermec PB41 Manuel utilisateur
Intermec
Intermec EasyCoder PF4ci Manuel utilisateur
Intermec
Intermec EasyCoder 601XP Manuel utilisateur
Intermec
Intermec 3600 Manuel utilisateur
Intermec
Intermec EasyCoder PD4 Manuel utilisateur
Intermec
Intermec PW50 Manuel utilisateur
Intermec
Intermec PB50 Manuel utilisateur
Intermec
Intermec PM4I Manuel utilisateur
Intermec
Intermec PW50 Manuel utilisateur
Intermec
Intermec PB50 Manuel utilisateur
Intermec
Intermec PB42 Manuel utilisateur
Intermec
Intermec PB42 Manuel
Intermec
Intermec 869 RFID Reader Mode d'emploi
Intermec
Intermec EasyCoder 3400e Manuel utilisateur
Intermec
Intermec EasyCoder 601XP Manuel utilisateur
Intermec
Intermec 074788 Series Manuel utilisateur
Intermec
Intermec EasyCoder 3400e Manuel utilisateur
Intermec
Intermec EasyCoder 4420 Manuel utilisateur
Intermec
Intermec EasyCoder PF2i Manuel utilisateur
Intermec
Intermec EasyCoder 501 SA Manuel utilisateur
