Intermec EasyCoder 4420 Manuel utilisateur
4420 and 4440 Printer
Self-Strip/Batch Takeup
P/N 066393-002
User’s Manual
Intermec Technologies Corporation
6001 36th Avenue West
P.O. Box 4280
Everett, WA 98203-9280
U.S. service and technical support: 1-800-755-5505
U.S. media supplies ordering information: 1-800-227-9947
Canadian service and technical support: 1-800-688-7043
Canadian media supplies ordering information: 1-800-268-6936
Outside U.S. and Canada: Contact your local Intermec service supplier.
The information contained herein is proprietary and is provided solely for the purpose of allowing
customers to operate and/or service Intermec manufactured equipment and is not to be released,
reproduced, or used for any other purpose without written permission of Intermec.
Information and specifications in this manual are subject to change without notice.
1998 by Intermec Technologies Corporation
All Rights Reserved
The word Intermec, the Intermec logo, JANUS, IRL, TRAKKER, Antares, Adara, Duratherm,
EZBuilder, Precision Print, PrintSet, Virtual Wedge, and CrossBar are either trademarks or
registered trademarks of Intermec Technologies Corporation. Throughout this manual, trademarked
names may be used. Rather than put a trademark (or ) symbol in every occurrence of a
trademarked name, we state that we are using the names only in an editorial fashion, and to the
benefit of the trademark owner, with no intention of infringement.
4420 and 4440 Printer Self-Strip/Batch Takeup User’s Manual
3
Introduction to the Self-Strip/Batch Takeup Option
The self-strip/batch takeup option enables the 4420 or 4440 printer to operate in
Self-Strip or Batch mode. When you use the printer in Self-Strip mode, the
printer strips each label off of the backing as it leaves the printer. When you use
the printer in Batch mode, the printer can collect an entire roll of media on the
media takeup hub.
This manual explains how to:
•load media to use self-strip.
•load media to use batch takeup.
•configure the printer for Self-Strip or Batch mode.
•clean the self-strip roller and sensors.
•troubleshoot the self-strip/batch takeup option.
Loading Media for Self-Strip
Self-strip allows you to apply labels as soon as they are printed by having the
printer peel the media backing away from individual labels one at a time. The
label taken sensor signals the printer that a label has been removed so that it
will print the next label.
For optimal performance, load your printer with Intermec self-strip media.
Fanfold media is not recommended because the backing might tear along the
perforation.
Note: After the printer prints the last label and passes the end of the media roll through
the printhead, the takeup hub will turn for a few revolutions before stopping.
To load media for self-strip
1. Turn off the printer.
2. Load media into the printer, leaving the media cover off. For help, see your
printer user’s manual.
3. Turn the head lift lever clockwise to raise the printhead.
4420 and 4440 Printer Self-Strip/Batch Takeup User’s Manual
4
4. Open the media access door.
Feed/Pause
Power/Data
Alert
Empty/Pause
Intermec
4420
44XXI.009
Media
access
door
Head
lift lever
5. Route the media below the self-strip roller.
Feed/Pause
Power/Data
Alert
Empty/Pause
Intermec
4420
44XXI.001
Self-strip
roller
Takeup hub
4420 and 4440 Printer Self-Strip/Batch Takeup User’s Manual
5
6. Place the end of the media in the media slot.
Feed/Pause
Power/Data
Alert
Empty/Pause
IntermecIntermec
4420
44XXI.002
Media lock
Media slot
7. Turn the media lock clockwise to lock the media in place.
8. Turn the takeup hub counterclockwise until the media fits snugly against
the takeup hub.
9. Turn the head lift lever counterclockwise to secure the printhead.
10. Close the media access door and replace the media cover.
11. On the back of the printer, turn on DIP switch number 8 on the top bank of
DIP switches.
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
O
1 2 3 4 5 6 7 8
I
OI
44XXI.003
12. Turn on the printer.
13. Configure the printer for Self-Strip mode. For help, see “Configuring Your
Printer for Self-Strip or Batch” later in this document.
4420 and 4440 Printer Self-Strip/Batch Takeup User’s Manual
6
Loading Media for Batch Takeup
Use batch takeup to collect printed media onto the takeup hub. The media can
spool directly onto the takeup hub or onto a core.
Note: After the printer prints the last label and passes the end of the media roll through
the printhead, the takeup hub will turn for a few revolutions before stopping.
To load media for batch takeup
1. Turn off the printer
2. Load media into the printer, leaving the media cover off. For help, see your
user’s manual.
3. Turn the head lift lever clockwise to raise the printhead.
4. Hook the batch guide over the top of the media access door and push down
on the bottom of the batch guide to latch it into place.
Feed/Pause
Power/Data
Alert
Empty/Pause
IntermecIntermec
4420
44XXI.004
Batch
guide
Head lift
lever
Media
access
door
4420 and 4440 Printer Self-Strip/Batch Takeup User’s Manual
7
5. Route the media around the batch guide.
Feed/Pause
Power/Data
Alert
Empty/Pause
Intermec
4420
44XXI.005
Takeup
hub
6. To have the media rolled onto the takeup hub, place the end of the media in
the media slot and turn the media lock clockwise to lock the media into
place.
Feed/Pause
Power/Data
Alert
Empty/Pause
Intermec
4420
44XXI.006
Media
lock
Media
slot
4420 and 4440 Printer Self-Strip/Batch Takeup User’s Manual
8
To have the media rolled onto an empty core, place the core onto the takeup
hub, turn the media lock clockwise to lock the core into place, and tape the
end of the media to the core.
Feed/Pause
Power/Data
Alert
Empty/Pause
Intermec
4420
44XXI.007
Intermec
4420
Empty
core
Media
lock
7. Turn the media takeup hub counterclockwise until the media fits snugly
against the takeup hub.
8. Turn the head lift lever counterclockwise to secure the printhead.
9. Replace the media cover.
10. In the back of the printer, turn on DIP switch number 8 on the top bank of
DIP switches.
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
O
1 2 3 4 5 6 7 8
I
OI
44XXI.003
11. Turn on the printer.
12. Configure the printer for batch. For help, see “Configuring Your Printer for
Self-Strip or Batch” later in this document.
4420 and 4440 Printer Self-Strip/Batch Takeup User’s Manual
9
Configuring Your Printer for Self-Strip or Batch
The following procedure explains how to use PrintSet to enable either Self-Strip
or Batch mode. To operate in Self-Strip mode, the media must be loaded onto
the takeup hub. The printer can operate in Batch mode without the media being
loaded onto the takeup hub; the printed media will collect in front of the
printer instead of into a roll on the takeup hub.
This procedure also explains setting the label width and configuring the printer
for a hot and humid environment.
To configure your printer for Self-Strip or Batch mode
1. Connect the printer to your PC and start PrintSet.
Note: Under the Printer Select menu, check that PrintSet is set up for your printer
(4420 or 4440). To customize the configuration for your printer, see the Help
menu.
2. Click the Paper Handling button.
3. From the Paper Handling dialog box, select Self-Strip or Batch.
4420 and 4440 Printer Self-Strip/Batch Takeup User’s Manual
10
4. If you work in a hot or humid environment (temperature at or above 104°F
[40°C] and humidity at or above 90 percent), select the Hot/Humid
Environment box.
5. Choose OK.
6. Click the Paper Type button.
7. From the Paper Type dialog box, set the Label Width to match the width of
the media in the printer. The default setting is 4 inches.
8. For Self-Strip mode, make sure you select Gap under Label Stock.
9. Choose OK.
Note: If you want to change other configuration settings, you should do so before
going to Step 10. For help changing the configuration, see the Help menu.
Autres manuels pour EasyCoder 4420
9
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Intermec Accessoires pour imprimantes
Intermec
Intermec Font Card Manuel utilisateur
Intermec
Intermec EasyCoder 501 SA Manuel utilisateur
Intermec
Intermec EasyCoder PF2i Manuel utilisateur
Intermec
Intermec PW50 Manuel utilisateur
Intermec
Intermec PC43t Manuel utilisateur
Intermec
Intermec EasyCoder 501 SA Manuel utilisateur
Intermec
Intermec 825-192-001 Manuel utilisateur
Intermec
Intermec 869 RFID Reader Mode d'emploi
Intermec
Intermec EasyCoder PD41 Manuel utilisateur
Intermec
Intermec EasyCoder PF2i Manuel utilisateur
Intermec
Intermec PB42 Manuel utilisateur
Intermec
Intermec EasyCoder 501XP Manuel utilisateur
Intermec
Intermec UBI EasyCoder 601 E Mode d’emploi
Intermec
Intermec 074788 Series Manuel utilisateur
Intermec
Intermec PB42 Manuel
Intermec
Intermec EasyCoder PC4 Manuel utilisateur
Intermec
Intermec PB50 Manuel utilisateur
Intermec
Intermec EasyCoder PF2i Manuel utilisateur
Intermec
Intermec EasyCoder PF2i Manuel utilisateur
Intermec
Intermec EasyCoder 601XP Manuel utilisateur
