Interlogix UVC-XP4DN-HR Manuel utilisateur

UVC-XP4DN-HR(-P)

Camera Quick Start

Guide

P/N 1079203A-EN • REV 1.0 • ISS 20DEC11

Trademarks and

patents

Interlogix, and UltraView names and logos are trademarks of

UTC Fire & Security.

Other trade names used in this document may be trademarks

or registered trademarks of the manufacturers or vendors of the

respective products.

Manufacturer UTC Fire & Security Americas Corporation, Inc.

2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification

N4131

FCC compliance Class A: This equipment has been tested and found to comply

with the limits for a Class A digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own

expense.

ACMA compliance Notice! This is a Class A product. In a domestic environment

this product may cause radio interference in which case the

user may be required to take adequate measures.

Canada This Class A digital apparatus complies with Canadian ICES-

003.

Cet appareil numérique de la classe A est conforme à la norme

NMB-0330 du Canada.

European Union

directives

12004/108/EC (EMC directive): Hereby, UTC Fire & Security

declares that this device is in compliance with the essential

requirements and other relevant provisions of Directive

2004/108/EC.

2002/96/EC (WEEE directive): Products marked with this

symbol cannot be disposed of as unsorted municipal waste in

the European Union. For proper recycling, return this product to

your local supplier upon the purchase of equivalent new

equipment, or dispose of it at designated collection points. For

more information see: www.recyclethis.info.

Contact

information

For contact information, see www.interlogix.com or

www.utcfssecurityproducts.eu.

Quick Start Guide 3 EN

Content

Package contents 3

Installation 3

Video connections 4

Set the lens mode 4

Attach the lens 5

Connect power 6

Mount the camera 6

Connect the monitor 7

Programming 7

OSD controls 7

Main menu 7

Specifications 9

Menu map 12

Package contents

Check the package and contents for visible damage. If any

components are damaged or missing, do not attempt to use the unit;

contact the supplier immediately. If the unit is returned, it must be

shipped back in its original packaging.

Package contents:

Multilingual Quick Start Guide

CD with User Manual in several languages

Camera

C-mount adaptor

CAUTION: Use direct plug-in UL listed power supplies marked Class

2 or LPS (limited power source) of the required output rating as listed

on the unit.

Installation

This section provides information on how to install the camera.

EN 4 Quick Start Guide

Video connections

Figure 1: Making the video connections

1. Connect a coaxial cable terminated with BNC connectors between

the MON OUT connector of the camera and the video in connector

on a test or local monitor.

2. Connect a coaxial cable terminated with BNC connectors between

the VIDEO OUT connector of the camera and the video in

connector on a monitor, multiplexer, switcher, or other standard

video device.

Set the lens mode

If your lens has a manual iris, ignore this switch. It is for autoiris lenses

only.

Figure 2: Lens mode DIP switch and iris level adjustment







1. Set to VD (video drive) for autoiris lenses with built-in amplifier.

2. Set to DD (direct drive) for autoiris lenses without amplifier.

3. DD adjustment.

Quick Start Guide 5 EN

Note: When the lens mode DIP switch is set to DD, you can use the

DD level screw (iris level adjustment) to ensure the correct exposure of

images for the camera’s position and the lighting conditions. Use an

insulated tool to rotate the screw. Observe the results on the monitor

screen for the best setting.

Attach the lens

Refer to the instructions that came with the lens you purchased for

complete installation instructions of that lens.

Note: For optimal performance, use an autoiris lens.

Figure 3: Attaching your lens

Video-type autoiris lens leads DC-type autoiris lens leads

C-mount adapter

(for C-mount lenses only)

A E

B F

C G

D H

Camera Autoiris, lens

connector

Autoiris lens

plug

Lens (autoiris shown);

manual iris has no

cable

Video-type autoiris lens leads: A. Red (9 VAC); B. NC (no connection); C. Black

(ground); D. White (video)

DC-type autoiris lens leads: E. Damping coil (+); F. Damping coil (-); G. Driving coil

(+); H. Driving coil (-)

1. If you are using a C-mount lens, screw on the provided C-mount

adapter.

2. Screw your customer-supplied lens onto the camera.

EN 6 Quick Start Guide

3. If you are using an autoiris lens, insert the autoiris lens plug into

the autoiris lens connector.

Connect power

Caution: Use direct plug-in UL listed power supplies marked Class 2

or LPS (limited power source) of the required output rating as listed on

the unit.

Figure 4: Power connection

1. With a screwdriver, loosen the GND and ~AC24V/DC12V terminal

screws on the terminal block.

2. Connect a universal 12 VDC, 24 VAC power supply to the terminal

block.

Note: The terminal block is not polarity- sensitive. Either power lead

can be connected to either terminal connector. There is no need for an

isolated ground wire. The two power terminals can accept any polarity

and any combination of power that equals 12 VDC or 24 VDC.

3. Retighten the terminal screws until snug, ensuring that the power

leads are secure.

4. Supply power to the unit by plugging the power supply into a

proper source.

Note: The power LED illuminates to show that the camera is receiving

power. If it does not illuminate, check the terminal block connections

and the power source

Mount the camera

To mount the camera, attach the camera to the mounting surface using

the appropriate fasteners.

Quick Start Guide 7 EN

Connect the monitor

Program the cameras by attaching a standard video monitor to the

system.

To connect the monitor, do the following:

1. Plug the monitor output cable to the video monitor output

connector (see Figure 1 on page 4.)

2. Connect the BNC cable to the video monitor.

3. Press Enter (Figure 5 below) to display the Setup menu.

Programming

OSD controls

Use the OSD (on-screen display) setup menus to program the camera.

See Figure 5.

Note: If you do not press a button for two minutes, your changes are

saved, and the camera returns to its normal function.

Figure 5: OSD menu controls

Down

Enter

Left

Right

Note: Wherever the PREVIOUS PAGE option appears, use it to leave

the current menu and return to the previous menu. Move to the

PREVIOUS PAGE option and press the center button.

Main menu

The camera is configured through the setup menus which appear on-

screen.

EN 8 Quick Start Guide

To access and navigate the main menu, press and hold the center

button of the OSD (See Figure 5). Use the up or down buttons to move

between items, and press the center button to select that item. Use the

left and right buttons to select the different options available for the

item.

You can return to the previous menu from any of the menus (except

the Main menu) by selecting the Previous page option.

There is a menu map on the back page of the manual that shows an

overview of the menus.

Refer to the User Manual for detailed programming instructions.

Figure 6: Main menu

Table 1: Main menu options

Menu option Function

Presets Configures the preset for the lighting condition.

Setup Configures camera ID, video I/O, type of lens, motion

detection, and wide dynamic range options.

Viewing Configures flip, resolution, gamma correction, image

sharpness, and saturation settings.

Exposure Configures automatic gain control (AGC), AE

preferences, range, shutter limit, and advanced

exposure limits.

White balance Configures white balance (WB) mode, magenta control,

WB bias, and auto tracking white balance.

Save/restore Displays firmware version, resets camera, saves user

settings, restores user settings, and restores factory

settings.

Exit Exits the OSD menu system.

Quick Start Guide 9 EN

Specifications

Electrical

Power Input 12 VDC or 24 VAC

Power consumption 3W (DC); 2.4 W (AC)

Environmental and physical

Weight 33.8 oz. (958 g)

Dimensions 5.22 x 4.11 in. (133 x 105 mm)

Operating temperature -58 to +122°F (-50 to +50°C)

Weather resistant IP66

EN 10 Quick Start Guide

Autres manuels pour UVC-XP4DN-HR

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Interlogix Caméra de sécurité

Interlogix

Interlogix TVB-5301 Manuel utilisateur

Interlogix

Interlogix UVD-XP4DNR(-P) Manuel utilisateur

Interlogix

Interlogix TVW-6101 Manuel utilisateur

Interlogix

Interlogix TruVision TVB 2102 Manuel utilisateur

Interlogix

Interlogix TVB-WBS Manuel utilisateur

Interlogix

Interlogix TVC-5120-1 Manuel utilisateur

Interlogix

Interlogix TruVision TVB-2402 Instructions d'utilisation et d'entretien

Interlogix

Interlogix TVD-6120VE-2-N Manuel utilisateur

Interlogix

Interlogix TruVision Line Manuel utilisateur

Interlogix

Interlogix UltraView PTZ Manuel utilisateur

Interlogix

Interlogix TruVision TVC-6110-1 Instructions d'utilisation et d'entretien

Interlogix

Interlogix TVP-6102 Manuel utilisateur

Interlogix

Interlogix UltraView UVC-6130-1-N Manuel utilisateur

Interlogix

Interlogix FW5.1 Manuel utilisateur

Interlogix

Interlogix TruVision TVB-4410 Manuel

Interlogix

Interlogix TruVision 4 Series Manuel utilisateur

Interlogix

Interlogix TruVision TVP-5101 Feuille d'instructions

Interlogix

Interlogix UVD-XP4DNR(-P) Manuel utilisateur

Interlogix

Interlogix TruVision TVB-2403 Feuille d'instructions

Interlogix

Interlogix MobileView MVC-7100-29-BL Manuel utilisateur

Interlogix

Interlogix TruVision TVB-2402 Feuille d'instructions

Interlogix

Interlogix UltraView IP PTZ 36X Manuel utilisateur

Interlogix

Interlogix 4 SERIES Feuille d'instructions

Interlogix

Interlogix UVD-XP3DNR Instructions de montage

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur