Interlogix TruVision 11 Series Manuel utilisateur

TruVision

11/31

Series

Wi-Fi IP

Camera Installation

Guide

P/N 1072907-EN • REV B • ISS 24APR15

Interlogix is part of UTC Building & Industrial Systems, a unit of United

Trademarks and patents

Trade names used in this document may be trademarks or registered trademarks

of the manufacturers or vendors of the respective products.

Manufacturer

Interogix

2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification

N4131

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

CC Caution

To assure continued compliance, use only shielded interface cables when

connecting to computer or peripheral devices. Any changes or modifications not

expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference

(2) This Device must accept any interference received, including interference that

may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Federal Communication Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure set forth for an

uncontrolled environment. In order to avoid the possibility of exceeding the FCC

radio frequency exposure limits, human proximity to the antenna shall not be less

than 20 cm (8 inches) during normal operation.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF

THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio

equipment and telecommunication terminal Equipment and the mutual

recognition of their conformity (R&TTE). The R&TTE Directive repeals and

replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment

and Satellite Earth Station Equipment) as of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who

install and use it. However, special attention must be paid to the dangers of

electric shock and static electricity when working with electrical equipment. All

guidelines of this and of the computer manufacture must therefore be allowed at

all times to ensure the safe use of the equipment.

National Restrictions

This device is intended for home and office use in all EU countries (and other

countries following the EU directive 1999/5/EC) without any limitation except for

the countries mentioned below:

Country Restriction Reasons/remarks

Bulgaria

None

General authorization required for

outdoor use and public service

France

Outdoor use;

limited to 10 mW

e.i.r.p. within the

band 2454-

2483.5 MHz.

Military Radiolocation use. Refarming

of the 2.4 GHz band has been ongoing

in recent years to allow current relaxed

regulation. Full implementation

planned 2012

Luxembourg

None

General authorization required for

network and service supply(not for

spectrum).

Annex 3 B and A Wideband Data Transmission systems 2400.0-2483.5 MHz:

Country Restriction Reasons/remarks

Norway

Implemented

This subsection does not apply for the

geographical area within a radius of

20 km from the centre of Ny-Ålesund.

Italy

Implemented

The public use is subject to general

authorization by the respective service

provider.

Russian

Federation

Limited

implementation

1. SRD with FHSS modulation

1.1. Maximum 2.5 mW e.i.r.p.

1.2. Maximum 100 mW e.i.r.p.

Permitted for use SRD for outdoor

applications without restriction on

installation height only for purposes of

gathering telemetry information for

automated monitoring and resources

accounting systems. Permitted to use

SRD for other purposes for outdoor

applications only when the installation

height is not exceeding 10 m above

the ground surface. 1.3 maximum

100 mW e.i.r.p. indoor applications.

2. SRD with DSSS and other than

FHSS wideband modulation

2.1. Maximum mean e.i.r.p. density is

2 mW/MHz. Maximum 100 mW e.i.r.p.

2.2. Maximum mean e.i.r.p. density is

20 mW/MHz. Maximum 100 mW

e.i.r.p. It is permitted to use SRD for

outdoor applications only for purposes

of gathering telemetry information for

automated monitoring and resources

accounting systems or security

systems.

2.3. Maximum mean e.i.r.p. density is

10 mW/MHz. Maximum 100 mW

e.i.r.p. indoor applications.

Ukraine

Limited

implementation

e.i.r.p. ≤100 mW with built-in antenna

with amplification factor up to 6 dBi.

The following information shall also be included in the case of radio equipment

intentionally emitting radio waves:

(a) frequency band(s) in which the radio equipment operates;

(b) maximum radio-frequency power transmitted in the frequency band(s) in

which the radio equipment operates.

2012/19/EU (WEEE directive): Products marked with this

symbol cannot be disposed of as unsorted municipal waste

in the European Union. For proper recycling, return this

product to your local supplier upon the purchase of

equivalent new equipment, or dispose of it at designated

collection points. For more information see:

www.recyclethis.info.

2006/66/EC (battery directive): This product contains a

battery that cannot be disposed of as unsorted municipal

waste in the European Union. See the product

documentation for specific battery information. The battery

is marked with this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg). For

proper recycling, return the battery to your supplier or to a

designated collection point. For more information see:

www.recyclethis.info.

Contact

information

For contact information, see www.interlogix.com or

www.utcfssecurityproducts.eu.

6 Installation Guide

Content

Introduction 7

Product overview 7

Installation 7

Installation environment 7

Package contents 8

Cable requirements 11

Camera description 11

Setting up the camera 12

Setting up Wi-Fi transmission 12

Accessing the SD card 19

Connecting a speaker 20

Mounting the wedge camera 21

Using the camera with a recorder 23

Using the camera with TruVision Navigator 24

Ensuring corrosion resistance 24

Specifications 25

TruVision IP wedge cameras 25

Pin definitions 26

Installation Guide 7

Introduction

Product overview

This is the installation guide for TruVision 11-31 Series Wi-Fi IP

camera models:

TVW-1103 (1.3MPX Wi-Fi, 2.8mm lens, Grey, PAL)

TVW-3103 (1.3MPX Wi-Fi, 2.8mm lens, Grey, NTSC)

TVW-1104 (1.3MPX Wi-Fi, 2.8mm lens, White, PAL)

TVW-3104 (1.3MPX Wi-Fi, 2.8mm lens, White, NTSC)

TVW-1105 (3MPX Wi-Fi, 2.8mm lens, Grey, PAL)

TVW-3105 (3MPX Wi-Fi, 2.8mm lens, Grey, NTSC)

TVW-1106 (3MPX Wi-Fi, 2.8mm lens, White, PAL)

TVW-3106 (3MPX Wi-Fi, 2.8mm lens, White, NTSC)

TVW-1116 (3MPX Wi-Fi, 6mm lens, White, PAL)

TVW-3116 (3MPX Wi-Fi, 6mm lens, White, NTSC)

Installation

This section provides information on how to install the cameras.

Installation environment

When installing your product, consider these factors:

•Electrical: Install electrical wiring carefully. It should be

done by qualified service personnel. Always use a proper

PoE switch or a 12 VDC UL listed Class 2 or CE certified

8 Installation Guide

power supply to power the camera. Do not overload the

power cord or adapter.

•Ventilation: Ensure that the location planned for the

installation of the camera is well ventilated.

•Temperature: Do not operate the camera beyond the

specified temperature, humidity or power source ratings.

The operating temperature of the camera is between -30

to +60°C (-22 to 140°F). Humidity is below 90%.

•Moisture: Do not expose the camera to rain or moisture,

or try to operate it in wet areas. Turn the power off

immediately if the camera is wet and ask a qualified

service person for servicing. Moisture can damage the

camera and also create the danger of electric shock.

•Servicing: Do not attempt to service this camera yourself.

Any attempt to dismantle or remove the covers from this

product will invalidate the warranty and may also result in

serious injury. Refer all servicing to qualified service

personnel.

•Cleaning: Do not touch the sensor modules with fingers. If

cleaning is necessary, use a clean cloth with some ethanol

and wipe the camera gently. If the camera will not be used

for an extended period of time, put on the lens cap to

protect the sensors from dirt.

Package contents

Check the package and contents for visible damage. If any

components are damaged or missing, do not attempt to use the

unit; contact the supplier immediately. If the unit is returned, it

must be shipped back in its original packaging.

Installation Guide 9

IP wedge camera

Camera

Installation manual

CD with Configuration

Manual and TruVision Device

Finder

Template A for mounting

with the converter pan

Template B for mounting

without the converter pan

Screws

Drywall anchor

Φ7.5 x 24.5mm (3 pcs)

Screw M4

(4 x 25mm (3 pcs)

10 Installation Guide

Water joint: provide water

resistance to network

connection.

12 VDC connector: DC jack

socket to terminal connectors

with positive and negative

indicators.

Screws C: M4×8, 2pcs

Tamper-resistant

hex wrench

Lens alignment tool

Converter pan

WEEE and battery

disposal

CAUTION: Use direct plug-in UL listed power supplies marked

Class 2/CE certified or LPS (limited power source) of the

required output rating as listed on the unit.

CAUTION: Risk of explosion if battery is replaced by an

incorrect type. Dispose of used batteries according to the

instructions.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Interlogix Caméra IP

Interlogix

Interlogix TruVision TVT-2202 Manuel utilisateur

Interlogix

Interlogix UltraSync RS-3230 Manuel utilisateur

Interlogix

Interlogix TruVision Line Manuel utilisateur

Interlogix

Interlogix TVB-1101 Feuille d'instructions

Interlogix

Interlogix TVB-5302 Feuille d'instructions

Interlogix

Interlogix TruVisioin 12 Series Manuel utilisateur

Interlogix

Interlogix TruVision Line Manuel utilisateur

Interlogix

Interlogix TVB-1101 Manuel utilisateur

Interlogix

Interlogix TruVision TVT-2201 Manuel utilisateur

Interlogix

Interlogix TVB-1101 Manuel utilisateur

Interlogix

Interlogix TruVision 12 Series Manuel utilisateur

Interlogix

Interlogix TruVision Bullet IR TVC-BIR6-SR Manuel utilisateur

Interlogix

Interlogix TruVision Line Feuille d'instructions

Interlogix

Interlogix TruVision Line Manuel utilisateur

Interlogix

Interlogix UltraSync RS-3230 Feuille d'instructions

Interlogix

Interlogix TruVision TVP-1101 Feuille d'instructions

Interlogix

Interlogix TruVision Open Standards Comment utiliser

Interlogix

Interlogix FW5.1 Manuel utilisateur

Interlogix

Interlogix UVD-IP-XP4DNR-VA2 Manuel utilisateur

Interlogix

Interlogix TruVision Line Manuel utilisateur

Interlogix

Interlogix 1073033-EN Manuel utilisateur

Interlogix

Interlogix UltraSync RS3130 Manuel utilisateur

Interlogix

Interlogix TVD-2202 Manuel utilisateur

Interlogix

Interlogix TruVision 11/31 Series Manuel utilisateur

Manuels Caméra IP populaires d'autres marques

FLIR

FLIR Exx series Manuel utilisateur

Avigilon

Avigilon H4A-BO1-IR Manuel utilisateur

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuel utilisateur

ShareTech

ShareTech AV1 Manuel utilisateur

Ezviz

Ezviz C6C Manuel utilisateur

Melchioni

Melchioni UCAM 2015 Manuel utilisateur

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuel utilisateur

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuel utilisateur

Mitel

Mitel 6800i Series Manuel de service

Vitek

Vitek VTC-IR403-212NP Manuel utilisateur

THOMSON

THOMSON DSC - 323W Manuel utilisateur

AVer

AVer FB2027 Manuel utilisateur

ENFORCER

ENFORCER EV-T5105-N2SQ Manuel utilisateur

Wansview

Wansview NC543 Manuel utilisateur

Eneo

Eneo MCB-64A0003M0A Manuel utilisateur

deView electronics

deView electronics CBDNI36F Manuel utilisateur

Swann

Swann SwannEye Manuel utilisateur

LevelOne

LevelOne IP CamSecure Manuel utilisateur