Intel RS3DC080 Manuel utilisateur

Thank you for buying an Intel® RAID Controller. Your Intel® RAID Controller provides

reliability, high performance, and fault-tolerant drive subsystem management, and it

offers an ideal RAID solution for the internal storage of workgroup, departmental, and

enterprise systems.The following information will help you assemble your Intel®RAID

Controller and install components.

Perform all installation work at an electrostatic discharge (ESD)-safe workstation that

meets the requirements of EIA-625, Requirements for Handling Electrostatic

Discharge Sensitive Devices. You must perform all actions in accordance to the latest

revision of the IPC-A-610 ESD-recommended practices.

This guide and other supporting documents are located on the web at:

http://www.intel.com/support.

G99270-001

Intel® RAID Controller RS3DC040/

RS3DC080

Quick Installation User's Guide

(This page is intentionally left blank.)

Table of Contents

General Installation Process ........................................................................................................ 2

Reference Documents .................................................................................................................... 3

Unpack the RAID Controller ............................................................................................ 2

Prepare the Host Computer ........................................................................................... 2

Install the RAID Controller .............................................................................................. 2

Conﬁgure and Install the SAS/SATA Devices ........................................................ 2

Connect the RAID Controller to the SAS/SATA Devices .................................. 2

Power up the System ....................................................................................................... 3

Run the Intel® RAID BIOS Conﬁguration Utility .................................................... 3

Install the Operating System Driver ........................................................................... 3

Product Overview ............................................................................................................................. 1

Warning

Read all caution and safety

statements in this document

before performing any of the

instructions. Also see the Intel

Server Board and Server Chassis

Safety Information document at:

http://www.intel.com/support/

motherboards/server/sb/cs-010770

.htm for complete safety information.

Warning

Installation and service

of this product to be

performed only by

qualiﬁed service personnel

to avoid risk of injury from

electrical shock or energy

hazard.

Caution

Observe normal ESD

[Electrostatic Discharge]

procedures during system

integration to avoid possible

damage to server board and/or

other components.

Tools Required

Anti-static

wrist strap

Phillips*

screwdriver

Intel®is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as

Product Overview

The Intel®RAID Controller RS3DC040/RS3DC080 is a PCI-Express®(PCIe®) 3.0, low-proﬁle controller with RAID control

capability, based on the LSISAS3108 RAID On-a-Chip (ROC) device.

• 12.0 Gb/s SAS III performance

The Intel® RAID Controller RS3DC040 uses 1 GB of DDR3 1866-MHz memory and controls four internal Serial Attached SCSI

(SAS) / Serial Advanced Technology Attachment (SATA) ports through one SFF-8643 mini-SAS HD-4i internal connector.

These 12Gb/s Intel® RAID Controllers are based on the LSI ﬁrst-to-market SAS IC technology and proven MegaRAID

technology. As third-generation PCIe RAID controllers, these controllers address the growing demand for increased data

throughput and scalability requirements across midrange and enterprise-class server platforms. These RAID controllers provide

these features:

• 6.0 Gb/s SATA III performance

• Eight-lane 8 GT/s PCIe host interface

SAS technology brings a wealth of options and ﬂexibility with the use of SAS devices and SATA devices within the same storage

infrastructure. However, SAS devices and SATA devices bring individual characteristics that make each one a more suitable

choice depending on your storage needs. MegaRAID products give you the ﬂexibility to combine these two similar technologies

on the same controller, within the same enclosure, and in the same virtual drive.

NOTE: These RAID controllers support SATA II and SATA III technologies.

For more information, including the technical speciﬁcations for your RAID controller, refer to the 12Gb/s Intel®RAID Controllers

User Guide on the Intel website http://www.intel.com/support.

NOTE: Record your RAID controller serial number in a safe location in case you need to contact Intel.

The Intel® RAID Controller RS3DC080 uses 1 GB of DDR3 1866-MHz memory and controls eight internal Serial Attached SCSI

(SAS) / Serial Advanced Technology Attachment (SATA) ports through two SFF-8643 mini-SAS HD-4i internal connectors. This

capability lets you use a system that supports both enterprise-class SAS drives and desktop-class SATA III drives.

General Installation Process

Unpack the RAID Controller

Unpack the RAID controller in a static-free environment. Remove the

controller from the antistatic bag, and inspect it for damage. A

low-proﬁle bracket is included with the RAID controller. If the RAID

controller appears to be damaged or the low-proﬁle bracket is missing,

contact Intel or your reseller support representative.

CAUTION: It is good practice to back up your data before

adding hardware, such as a RAID controller, to your system.

The latest versions of the documentation, drivers, and ﬁrmware are

available on the Intel website at http://www.intel.com/support. See

Reference Documents for more information.

The website contains utility programs, device drivers for various

operating systems, and related documentation.

Prepare the Host Computer

CAUTION: Before you install the RAID controller,

make sure that the host computer is disconnected

from the power and from any networks.

Turn off the host computer, and unplug the power cords

from the rear of the power supply. Remove the cover from

the host computer.

Install the RAID Controller

Insert the RAID controller into a PCIe slot on the motherboard in the

host computer, as shown in the following ﬁgure. Press down gently, but

ﬁrmly, to seat the RAID controller correctly in the slot. Secure the RAID

controller to the host computer chassis with the bracket screw.

NOTE: This RAID controller is a PCIe x8 card, and it can

operate in x8 or x16 slots. Some PCIe slots, however, support

only PCIe graphics cards; if a RAID controller is installed in

one of these slots, the RAID controller will not function. Refer

to the guide for your motherboard for information about the

PCIe slot.

Conﬁgure and Install the

SAS/SATA Devices

Conﬁgure and install the SAS devices, SATA devices, or

both in the host computer case.

Refer to the documentation for the devices for any

preinstallation conﬁguration requirements.

Connect the RAID Controller to

the SAS/SATA Devices

NOTE: Refer to the 12Gb/s Intel

RAID Controller

User Guide on the Intel website

http://www.intel.com/support for detailed

information about the SAS cables.

Use SAS cables to connect the RAID controller to SAS

devices, SATA devices, or both. Refer to 12Gb/s Intel

RAID Controller User Guide on the Intel website

http://www.intel.com/support for information about the

connector locations.

Edge of

Motherboard

PCIe Slot

Bracket

Screw

Press

Here

Press

Here

3_01495-01

Intel

RAID Controller

RS3DC080 as shown

General Installation Process

Power up the System

Reinstall the computer cover, and reconnect the power cords. Turn on

the power to the host computer. Make sure that the power is turned on

to the SAS devices and the SATA III devices before or at the same time

that the power to the host computer is turned on. If the power is

turned on to the host computer before it is turned on to the devices,

the host computer might not recognize the devices.

The ﬁrmware takes several seconds to initialize. During this time, the

RAID controller scans the ports.

Run the Intel® RAID BIOS

Conﬁguration Utility

Run the Intel

RAID BIOS Conﬁguration Utility to

conﬁgure the groups and the virtual drives. When the

message about the conﬁguration utility appears on the

screen, immediately press Ctrl+G to run the utility.

NOTE: Refer to the Intel

RAID Software User

Guide for detailed steps on conﬁguring drive

groups and virtual drives.

Install the Operating System Driver

The RAID controller can operate under various operating systems,

but you must install the software drivers ﬁrst.

You can view the supported operating systems and download the

latest drivers for RAID controllers from the Intel website at

http://www.intel.com/support.

Refer to the Intel

RAID Software User Guide on

http://www.intel.com/support for more information about installing

the driver. Be sure to use the latest service packs that are provided by

the operating system manufacturer and to review the readme ﬁle

that accompanies the appropriate driver.

Reference Documents

If you need more information about any topic covered in this guide, refer to the following documentation on the Intel website at http://www.intel.com/support:

•12Gb/s Intel

RAID Controllers User Guide

• Intel

RAID Software User Guide

•Software license agreement

G99270-001

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Intel Matériel informatique

Intel

Intel BFCBASE - Motherboard - 7300 Manuel utilisateur

Intel

Intel Xeon Phi Processor x200 Mode d’emploi

Intel

Intel Galileo Manuel utilisateur

Intel

Intel E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core... Manuel utilisateur

Intel

Intel Pentium 4 Guide de démarrage rapide

Intel

Intel BV80605001914AG - Processor - 1 x Xeon X3430 Manuel utilisateur

Intel

Intel Xeon 5500 Series Mode d’emploi

Intel

Intel NUC 13 Extreme Kit NUC13RNGi9 Manuel utilisateur

Intel

Intel RS2WG160 Manuel d'installation

Intel

Intel Xeon Processor E5-2600 Manuel utilisateur

Intel

Intel 852GME Mode d’emploi

Intel

Intel 80C186EC Manuel utilisateur

Intel

Intel 5100 Series Manuel utilisateur

Intel

Intel 925 - Pentium D 925 3.0GHz 800MHz 4MB-Cache Socket 775... Manuel utilisateur

Intel

Intel P8700 - Core 2 Duo Processor Manuel utilisateur

Intel

Intel RS2BL080 - RAID Controller Manuel utilisateur

Intel

Intel DH61BE Guide de configuration

Intel

Intel RS2PI008 Manuel utilisateur

Intel

Intel BX80580Q9400 - Core 2 Quad 2.66 GHz... Manuel utilisateur

Intel

Intel DG45ID - CARACTERISTIQUES TECHNIQUES Manuel utilisateur

Intel

Intel 810A3 Mode d’emploi

Intel

Intel IXP2400 Manuel utilisateur

Intel

Intel NUC 11 Pro Kit NUC11TNKi3 Manuel utilisateur

Intel

Intel SL6NQ - Xeon 2.4 GHz/533MHz/512 KB CPU Processor... Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

Advantech

Advantech ASMB-935 Series Manuel utilisateur

Jupiter

Jupiter RAM PACK Manuel utilisateur