Infineon PSoC 62S4 Manuel utilisateur

1 KitProg3 status LED (D10)

2 KitProg3 USB connector (J10)

3 PSoC 5LP programming header (J7)*

4 2.5 V selection jumper (J14)

5 PSoC 6 MCU power selection jumper (J12)

6 PSoC 5LP based KitProg3 programmer

and debugger (CY8C5868LTI-LP039, U7)

7 PSoC 6 MCU current measurement jumper (J13)

8 KitProg3 programming mode selection button (SW3)

9 Power LED (D14)

10 PSoC 6 MCU reset button (SW1)

11 Arduino™ UNO R3 compatible power header (J1)

12 PSoC 6 MCU 10-pin SWD/JTAG program and debug header (J8)

13 User LEDs (D12 and D13)

14 Arduino UNO R3 compatible I/O headers (J2, J3 and J4)

15 PSoC 6 MCU user button/hibernate wakeup (SW2)

16 PSoC 6 MCU (CY8C6244LQI-S4D92, U8)

17 CapSense™ buttons and slider (CSB1, CSB2 and CSS1)

18 Thermistor (TH1)

19 Ambient light sensor (Q8)

20 QSPI NOR flash (S25FL512SAGMFIR10, U9)

21 PSoC 6 MCU USB connector (J5)

22 PSoC 6 MCU extended I/O header (J11)*

23 External power supply connector (J9)*

* Footprint only, not populated on the board

PSoC 62S4 pioneer board details

PSoC 62S4 pioneer board pinout details

www.cypress.com/CY8CKIT-062S4

Quick start guide

PSoC™ 62S4 pioneer kit

CY8CKIT-062S4

The PSoCTM 62S4 pioneer kit (CY8CKIT-062S4) is a low-cost hardware

platform that enables you to design and debug applications using

the PSoC 62 MCU.

Kit contents

PSoC 62S4 pioneer board

USB type-A to micro-B cable

Six jumper wires (five inches each)

Quick start guide (this document)

›

10 11 12 14

13 15 16

1921 20142223

P6_4/SCL

P6_5/SDA

VREF/AREF

GND/GND

P2_2/D13

P2_1/D12

P2_0/D11

P2_3/D10

P2_6/D9

P2_4/D8

P6_3/D7

P6_2/D6

P5_7/D5

P5_6/D4

P5_1/D3

P5_0/D2

P0_3/D1

P0_2/D0

P8_1

P8_0

P7_3

P7_2

P7_1

P7_0

P2_7

P2_5

P0_4

P0_5

Arduino Uno R3 I/Os

LEGEND

PSoC 6 MCU I/Os

VTARG/IOREF

XRES/RESET

V 3.3/3.3 V

V 5.0/5 V

GND/GND

VIN/Vin

P10_0/A0

P10_1/A1

P10_2/A2

P10_3/A3

P10_4/A4

P10_5/A5

P10_6

P10_7

P9_0

P9_1

P9_2

P9_3

P3_0

P3_1

Before you start

› Ensure that you have the following:

• PC with USB port

• UART terminal soware such as Tera Term

or Minicom

›

Visit the kit website to download and install the

required soware.

› Ensure the jumper J12 is at position 2-3 to select 3.3 V.

› Connect the KitProg3 USB connector (J10) to your PC.

› Wait for the driver installation to complete.

Step 1: Connect the kit with UART terminal soware

› Open the UART terminal soware and connect to

the kit’s USB-UART COM port with the following settings:

• Baud rate: 115200 bps

• Data: 8 bit

• Parity: None

• Stop bit: 1 bit

• Flow control: None

› Press the XRES switch (SW1) to reset the device.

Step 2: Run the pre-programmed code example

› Follow the instructions displayed on the UART

terminal to use the pre-programmed

code example.

Step 3: Observe the user LED (D13) brightness variation

› Observe the state of the user LED (D13) with the variation

of ambient light intensity. The LED turns ON when the

ambient light intensity is lower than 45% and turns OFF

when higher than 55%.

Quick start guide

PSoC 62S4 pioneer board

USB-UART COM port setup

Instructions displayed on the UART terminal

Observe the brightness in LED (D13)

Document Number: 002-30749 Rev. *C

Ce manuel convient aux modèles suivants

Autres manuels Infineon Matériel informatique

Infineon

Infineon TRAVEO II Manuel utilisateur

Infineon

Infineon Traveo II CPU board Manuel utilisateur

Infineon

Infineon Cypress S6SATU01A Series Manuel utilisateur

Infineon

Infineon TRAVEO II CPU BOARD Manuel utilisateur

Infineon

Infineon DSO-8 Manuel utilisateur

Infineon

Infineon Traveo II CPU board Manuel utilisateur

Infineon

Infineon OPTIREG TLS850A4TEV50 Manuel utilisateur

Infineon

Infineon XMC1400 Manuel utilisateur

Infineon

Infineon AIROC CYW20829 Manuel utilisateur

Infineon

Infineon TLE493D-P2B6 MS2GO Manuel utilisateur

Infineon

Infineon ICL8001G Mode d’emploi

Infineon

Infineon AIROC CYW43022 Manuel utilisateur

Infineon

Infineon BTN9960 Manuel utilisateur

Infineon

Infineon CDM10V Manuel utilisateur

Infineon

Infineon XMC7200 Manuel utilisateur

Infineon

Infineon AN230264 Manuel utilisateur

Infineon

Infineon SPI F-RAM FM33256B Manuel utilisateur

Infineon

Infineon AIROC CYW20721 Manuel utilisateur

Infineon

Infineon AIROC IFW56810-00 Manuel utilisateur

Infineon

Infineon TLE4241SYS SHIELD Manuel utilisateur

Infineon

Infineon DEMO-MIPI-4K-CAM01 Manuel utilisateur

Infineon

Infineon CY8CPROTO-062S2-43439 Manuel utilisateur

Infineon

Infineon R 48V BATT Switch10 Manuel utilisateur

Infineon

Infineon EZ-PD CY4534 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur