Huawei SmartLogger2000 series Manuel utilisateur

HUAWEI TECHNOLOGIES CO., LTD.

SmartLogger2000

Quick Guide

Issue: 04

Part number: 31508122

Date: 2018-06-13

1Overview

1. The information in this document is subject to change without notice. Every effort has been made

in the preparation of this document to ensure accuracy of the contents. However, all statements,

information, and recommendations in this document do not constitute a warranty of any kind,

express or implied.

2. Before installing the device, carefully read the SmartLogger2000 User Manual to get familiar with

the product information and precautions. SmartLogger is short for SmartLogger2000 in the

following text.

3. Install and use the device according to this document and the user manual. Otherwise, the device

may be damaged. Use insulated tools when installing the device.

4. When the SmartLogger is applied in a non-Huawei smart array controller (smart array controller

for short), install it in the third-party cabinet. This section describes the installation and cable

connection operations using the SmartLogger in non-Huawei smart array controller scenario as

an example.

Model Description

1.1

NOTICE

Model

Description

Model

Description

SmartLogger2000

-10

10: with a built

in 500 V

AC PLC central

coordinator (CCO)

SmartLogger2000

-10-C 10-C: with a built-in

800 V AC PLC

central coordinator

(CCO)

11-C: with no built-

PLC CCO

SmartLogger2000

-10-B 10-B: with a built-in

500 V AC PLC

central coordinator

(CCO)

11-B: with no PLC

CCO

martLogger2000-11-C

SmartLogger2000

-11-B

N/A

The SmartLogger with a built-in PLC CCO can work with the SUN2000 integrated with the PLC

station (STA) to implement PLC networking.

If the SmartLogger with no built-in PLC CCO needs to work with the SUN2000 integrated with the

PLC STA to implement PLC networking, an external PLC CCO needs to be connected.

The Bluetooth module embedded in the SmartLogger2000-10 supports only the Android app. The

Bluetooth modules embedded in other models of SmartLoggers support both the Android app

and the iOS app.

This document uses the SmartLogger2000-10-C as an example to describe typical scenarios and

cable connections.

NOTE

Port Description

1.2

SmartLogger2000-10-C/11-C

No.

Port (Silk Screen)

Function Description

RF1, RF2

Reserved

Reserved.

12V OUT

12 V DC output

Provides 12 V DC power supply with a maximum

current of 100 mA.

12V IN

12 V DC input

Connects to the power adapter.

USB

USB port

Connects a USB flash drive.

SFP1, SFP2

Ethernet optical port

Connects to an ATB or another cascaded

SmartLogger.

ETH1, ETH2

Ethernet electrical

port

Connects to an Ethernet LAN switch, router, POE or

PC device.

Digital output (DO)

Relay output supports 12 V voltage and 0.5 A current.

COM1

–COM6

RS485

communications

Six RS485 ports that can be connected to devices

such as the SUN2000, box

-type transformer, power

meter, or EMI.

Default

Default key

Resets and restarts the Bluetooth module or resets

the SmartLogger IP address to the default IP address

(valid within 5 minutes). The default IP address is

192.168.0.10.

AC1, AC2

AC power cable

ports

SmartLogger2000

-10-C: Connects to three-

phase (A,

B, and C) inputs

, and is used for PLC with the

SUN2000 over AC power cables.

SmartLogger2000

-11-C: disabled

Shell

ground point

N/A

AI1

–AI7

Analog input

AI1 supports 0

–10 V input voltage (passiveb); AI2–

AI7

support 0

–20 mA and 4–

20 mA input current (passive).

PT1, PT2

Analog input



PT1 supports the connection to a three-wire or two-

wire PT100/PT1000 temperature sensor.



PT2 supports the connection to only a two-wire

PT100/PT1000 temperature sensor.

AO1

–AO4

Analog output (AO)

–20 mA and 0–20 mA output current

DI1

–DI8

Digital input (DI)

Connects to a dry contact input. GND1 and GND2 are

ground ports for DI signals.

Note a: When the

SmartLogger is applied in a non-smart array controller, connect the AC1 and AC2

ports to the SPD with the delivered cables. The residue voltage of the SPD should be less than 6 kV.

Note b: Passive means that the AI port can connect to a sensor that needs to be energized separately.

No. Port (Silk Screen) Function Description

RF1, RF2

Reserved

Reserved.

12V OUT

12 V DC output

Provides 12 V DC power supply with a maximum

current of 100 mA.

12V IN

12 V DC input

Connects to the power adapter.

USB

USB port

Connects a USB flash drive.

SFP1, SFP2

Ethernet optical port

Connects to an ATB or another cascaded

SmartLogger.

ETH1, ETH2

Ethernet electrical

port

Connects to an Ethernet LAN switch, router, POE or

PC device.

Digital output (DO)

Relay output supports 12 V voltage and 0.5 A current.

COM1

–COM6

RS485

communications

Six RS485 ports that can be connected to devices

such as the SUN2000, box

-type transformer, power

meter, or EMI.

Default

Default key

Resets and restarts the Bluetooth module or resets

the SmartLogger IP address to the default IP address

(valid within 5 minutes). The default IP address is

192.168.0.10.

AC1, AC2

AC power cable

ports



SmartLogger2000-10/10-

B: Connects to the A/B/C

three-phase input, and used for PLC with the

SUN2000 over AC power cables.



SmartLogger2000-11-B: disabled

Shell

ground point

N/A

AI1

–AI8

Analog input



SmartLogger2000-10: AI1–AI4: 4–20 mA and 0–

mA input current (passivea); AI5–AI8: 4–

20 mA and

0–20 mA input current (activeb)



SmartLogger2000-10-B/11-B: AI1: 0–10 V input

voltage (passive); AI2–AI4: 4–20 mA and 0–

20 mA

input current (passive); AI5–AI8: 4–20 mA and 0–

20 mA input current (active)

AO1

–AO6

Analog output (AO)

–20 mA and 0–20 mA output current

DI1

–DI8

Digital input (DI)

Connects to a dry contact input. GND1 and GND2

are ground ports for DI signals.

Note a: Passive means that the AI port can connect to a sensor that needs to be energized separately.

Note b: Active means that the AI port can connect to a sensor that need not be energized separately.

SmartLogger2000-10/10-B/11-B

2Typical Cable Connection Scenarios

Smart Array Controller Scenario

2.1

This document describes the application scenario where the SmartLogger is inside the smart

array controller SmartACU2000B-D-2PID/2PLC.

The tables under figures list only the components to be configured by the customer in the

corresponding scenario.

NOTE

NOTICE

1. Prepare the single-phase AC power cable for the smart array controller by yourself.

Recommended: a two-core outdoor armor copper cable with an operating voltage to the ground

greater than or equal to 300 V and a cross-sectional area of 4 mm2for each core wire

2. Prepare the power cable from the miniature circuit breaker (MCB) to the station-service power

source by yourself. Recommended: a two-core outdoor armor copper cable with an operating

voltage to the ground greater than or equal to 300 V and a cross-sectional area of 4 mm2for each

core wire

3. Prepare the three-phase AC power cable for the smart array controller by yourself. Recommended:

a four-core (L1, L2, L3, and functional earthing) outdoor armor copper cable with a cross-sectional

area of 10 mm2for each core wire. When the rated AC voltage on the low-voltage side of the box-

type transformer is less than or equal to 500 V, the operating voltage between the three-phase AC

power cable and the ground should be greater than or equal to 600 V. When the rated AC voltage

on the low-voltage side of the box-type transformer is greater than 500 V and less than or equal to

800 V, the operating voltage between the three-phase AC power cable and the ground should be

greater than or equal to 1000 V.

4. Prepare the power cable from the busbar to the Three-phase power switch by yourself.

Recommended: a four-core (L1, L2, L3, and functional earthing) outdoor armor copper cable with a

cross-sectional area of 10 mm2for each core wire. When the rated AC voltage on the low-voltage

side of the box-type transformer is less than or equal to 500 V, the operating voltage to the ground

should be greater than or equal to 600 V. When the rated AC voltage on the low-voltage side of

the box-type transformer is greater than 500 V and less than or equal to 800 V, the operating

voltage to the ground should be greater than or equal to 1000 V.

Optical Fiber

Location Component Recommended Model or

Specifications Component

Source Quantity

Smart array

controller

LAN switch (optional) UT-H605 or ES1000 Can be

purchased

from Huawei 1

Fitting bag

for optical

ring

switching

Low-

speed

optical

module

FTLF1323P1BTR-HW Can be

purchased

from Huawei

Optical

jumper

PLCLC5S-ST3P302-HW, LC-

LC-S2-L2,

3ECA1031LCLC002-01-F, or

LP-LP-2S-P-SM-002

Box-type

transformer

MCB Rated current: 32 A, number of

poles: 2 Prepared by

the customer 1

Three-

phase

power

switch

Knife

fuse

switch

(solution

When the rated AC voltage

on the low-voltage side of

the box-type transformer is

less than or equal to 500 V,

the rated voltage should be

greater than or equal to 500

V. When the rated AC

voltage on the low-voltage

side of the box-type

transformer is greater than

500 V and less than or

equal to 800 V, the rated

voltage should be greater

than or equal to 800 V.

Rated current of the fuse:

32 A; rated current of the

knife fuse switch box ≥ 32 A;

number of poles: 3 (3 fuses

for each knife fuse switch

box)

Prepared by

the customer

Scenario with a

double-column

transformer: 1

Scenario with a

dual-split

transformer: 2

MCCB

(solution

When the rated AC voltage

on the low-voltage side of

the box-type transformer is

less than or equal to 500 V,

the rated voltage should be

greater than or equal to 500

V. When the rated AC

voltage on the low-voltage

side of the box-type

transformer is greater than

500 V and less than or

equal to 800 V, the rated

voltage should be greater

than or equal to 800 V.

Let-through energy ≤ 1.26 x

106A2s

Rated current: 32 A;

number of poles: 3

Prepared by

the customer

4G LTE

Location Component Recommended Model or

Specifications Component

Source Quantity

Smart array

controller

LAN switch (optional) UT-H605 or ES1000 Can be

purchased

from Huawei 1

Fitting

bags for

the POE

module

and

customer-

premises

equipment

(CPE)

POE

module N/A Can be

purchased

from Huawei 1

Outside the

smart array

controller

and box-

type

transformer

CPE N/A Can be

purchased

from Huawei 1

Box-type

transformer

MCB Rated current: 32 A, number of

poles: 2 Prepared by

the customer 1

Three-

phase

power

switch

Knife

fuse

switch

(solution

When the rated AC voltage

on the low-voltage side of

the box-type transformer is

less than or equal to 500 V,

the rated voltage should be

greater than or equal to 500

V. When the rated AC

voltage on the low-voltage

side of the box-type

transformer is greater than

500 V and less than or

equal to 800 V, the rated

voltage should be greater

than or equal to 800 V.

Rated current of the fuse:

32 A; rated current of the

knife fuse switch box ≥ 32 A;

number of poles: 3 (3 fuses

for each knife fuse switch

box)

Prepared by

the customer

Scenario with

a double-

column

transformer: 1

Scenario with

a dual-split

transformer: 2

MCCB

(solution

When the rated AC voltage

on the low-voltage side of

the box-type transformer is

less than or equal to 500 V,

the rated voltage should be

greater than or equal to 500

V. When the rated AC

voltage on the low-voltage

side of the box-type

transformer is greater than

500 V and less than or

equal to 800 V, the rated

voltage should be greater

than or equal to 800 V.

Let-through energy ≤ 1.26 x

106A2s

Rated current: 32 A; number

of poles: 3

Prepared by

the customer

Non-Smart Array Controller Scenario

2.2

NOTICE

Optical Fiber

1. If the SmartLogger communicates with a SUN2000 over an AC power cable, an MCB and a knife

switch need to be installed to prevent device damage in the case of short circuits.

2. If the SmartLogger communicates with the SUN2000 over an AC power cable, prepare the cable

from the knife fuse switch to the MCB and the cable from the busbar to the knife fuse switch by

yourself. Recommended: a three-core outdoor armor cable with a cross-sectional area of 10 mm2

for each core wire. When the rated AC voltage on the low-voltage side of the box-type transformer

is less than or equal to 500 V, the operating voltage between the AC power cable and the ground

should be greater than or equal to 600 V. When the rated AC voltage on the low-voltage side of

the box-type transformer is greater than 500 V and less than or equal to 800 V, the operating

voltage between the AC power cable and the ground should be greater than or equal to 1000 V.

3. The SmartLogger can connect to the SUN2000 through an RS485 communications cable or AC

power cable. If RS485 is used, there is no need to connect an AC power cable between the

SmartLogger and the MCB in the scenario without a smart array controller.

4. The power cable delivered with the SmartLogger is 1 meter long, the power adapter cable is 1.5

meters long, the network cable is 2.2 meters long, and the AC power cable is 1.5 meters long.

Reserve the installation positions for components based on the cable lengths.

Autres manuels pour SmartLogger2000 series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Huawei Unité de contrôle

Huawei

Huawei UPS5000-H-400K-NT Manuel utilisateur

Huawei

Huawei MG301 Instructions d'installation

Huawei

Huawei MU509-65 Instructions d'installation

Huawei

Huawei MU739 Instructions d'installation

Huawei

Huawei ME909s Series Instructions d'installation

Huawei

Huawei EM770S Manuel utilisateur

Huawei

Huawei MU509 Series Instructions d'installation

Huawei

Huawei MU609 Instructions de montage

Huawei

Huawei ICD OPS D Series Manuel utilisateur

Huawei

Huawei ME909u-523 Instructions d'installation

Huawei

Huawei VP9660 Manuel utilisateur

Huawei

Huawei ME906A Instructions de montage

Huawei

Huawei UPS5000-H Series Manuel utilisateur

Huawei

Huawei EM660C EVDO Manuel utilisateur

Huawei

Huawei MU709 Series Instructions d'installation

Huawei

Huawei MU609 Instructions d'installation

Huawei

Huawei ECC500 Manuel utilisateur

Huawei

Huawei SmartAX MA5675 Manuel utilisateur

Huawei

Huawei MU609 Instructions d'installation

Huawei

Huawei ME909s-120 Instructions d'installation

Huawei

Huawei PDU5000 Manuel utilisateur

Huawei

Huawei RRU3269 Manuel utilisateur

Huawei

Huawei UPS5000-E-400K-SMS Manuel utilisateur

Huawei

Huawei EDFA0820-D Manuel d'utilisation

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur