Huawei PDU5000 Manuel utilisateur

HUAWEI TECHNOLOGIES CO., LTD.

PDU5000

Quick Guide

Parts No.:02121671

Issue:01

Date:2019-01-10

1Safety Precautions

1. General safety precautions

To ensure human safety and equipment security, pay attention to all the precautions marked on the

equipment and instructed in the product documentation.

The "NOTICE", "CAUTION", "WARNING", and "DANGER" statements in this document do not

represent all the safety instructions. They are only supplements to the safety instructions.

2. Local laws and regulations

Comply with local laws and regulations when operating the equipment. The safety instructions in

the document are only supplements to the local laws and regulations.

3. Personnel requirements

Personnel who plan to install or maintain Huawei equipment must receive a thorough training,

understand all necessary safety precautions, and be able to perform all operations correctly.

•Only trained and qualified personnel are allowed to install, operate, and maintain the equipment.

•Only personnel certified or authorized by Huawei are allowed to replace or change the equipment

or components (including software).

•Any fault or error that might cause safety problems must be reported immediately to a supervisor.

4. Grounding requirements

•When installing the equipment, ground it first.

•When removing the equipment, disconnect the ground cable finally.

•Do not damage the ground conductor.

•Do not operate the equipment in the absence of a properly installed ground conductor.

•The equipment must be grounded permanently. Before operating the equipment, check the

electrical connection of the equipment to ensure that it is securely grounded.

5. Personal requirements

•Do not operate the equipment or cables during thunderstorms.

•Remove the AC power connector and do not use the fixed terminal or touch the terminal or

antenna connector in a thunderstorm.

•Before operating the equipment, wear electrostatic discharge (ESD) clothes, ESD gloves, and an

ESD wrist strap. Do not wear conductors such as jewelry or watches when operating the

equipment.

•In the case of a fire, immediately leave the building or the equipment area, and turn on the fire

alarm bell or make an emergency call. Never enter a building or equipment area that is on fire.

6. Equipment requirements

•Before operations, ensure that the equipment is firmly secured to the floor or other solid objects,

such as a wall or an installation rack.

•Do not block the air vent while the system is operating.

•Tighten the screws using tools when installing panels.

•After installation, remove the packing materials from the equipment area.

2Overview

No.

Component Name

No.

Component Name

AC input

circuit breaker

Surge protective device (SPD)

switch

SPD

AC output circuit breaker

AC output terminal block

AC input terminal block

N/A

1. Appearance dimensions of the PDU5000.

2. Feature Introduction of the PDU5000.

1 2 34

5 6 7

Front view of the PDU5000

Back view of the PDU5000

430

630

664

482.6

130

Front

Back

Unit: mm

•Unpack the equipment and visually inspect its appearance to check whether the equipment is

paint-peeling, misshapen, scratched, or soaked. If so, record the information and contact the

equipment carrier and the local Huawei office immediately.

•Check against the packing list that the equipment and components are correct and complete. If

some components are missing or do not conform to the packing list, record the information and

contact Huawei or the local Huawei office immediately.

3Unpacking and Acceptance

Installing PDU5000 Cables

1. Elementary diagram of the PDU5000.

2. Install cables for the PDU5000 by referring to the following figure.

S201-D63A/1P

1QF

FS/20K A

QF2

C32A/1P

QF3

C32A/1P

QF4

C32A/1P

QF5

C32A/1P

QF6

C32A/1P

QF7

B10A/2 PRCD

QF8

B10A/2 PRCD

QF9

B10A/1 P

QF10

B10A/1 P

QF11

B10A/1 P

QFS

C32A/2P

QF1

C32A/1P RVVZ-3x6

RVVZ-3x6

RVVZ-3x1.0

L,N,PE

AC Input

AC Output

EquipmentroomPE

InputPE OutputPE

No.

Check Item

Check Result

All cables are correctly connected based on the Schematic Diagram.

□

Passed □Failed

Ground cables are securely connected.

□

Passed □Failed

Redundant parts of the ground cables and power cables are cut off

instead of coiled.

□

Passed □Failed

Power cables and ground cables are routed and bundled separately from

other types of cables.

□

Passed □Failed

All circuit breakers are OFF.

□

Passed □Failed

The appearance is intact without any damage.

□

Passed □Failed

All labels are correct, clear, and complete.

□

Passed □Failed

The surrounding area of the cabinet contains no waste tape, cable ties,

paper, or packing materials.

□

Passed □Failed

All bolts are tightened, especially the bolts used for electrical connection.

Flat washers and spring washers are installed properly in the correct

sequence.

□

Passed □Failed

Cables are bundled neatly, and cable ties are secured evenly and

properly in the same direction.

□

Passed □Failed

Cables are routed for ease of future maintenance and expansion.

□

Passed □Failed

There is no unnecessary adhesive tape or cable tie on the cables.

□

Passed □Failed

Exposed parts near the wiring terminals and lugs are wrapped in PVC

insulation tape or heat shrinking tubing.

□

Passed □Failed

Flat and spring washers are properly installed on each bolt of a wiring

terminal.

□

Passed □Failed

The power and signal cables are routed in accordance with the weak

and strong

current cable routing specifications and the cable routing plan.

□

Passed □Failed

Check Before Power-On

1. Turn on the SPD circuit breaker.

2. Turn on the external power input circuit breaker.

3. Turn on the input switch.

4. Turn on all output circuit breakers of the PDU5000 in sequence and check that the output voltage

is normal by using a multimeter.

5. After checking that the parameters are normal, turn off all the circuit breakers one by one and

disconnect the power supply.

Power-On Commissioning

When switching on the circuit breakers, observe whether there is any abnormal phenomenon, such

as sparks or unsmooth switching on/off.

NOTE

Item

Interval

Operation

Guide

Reference Standard

Troubleshooting

Connections of

input and output

power cables

Monthly

Visual

observation

The cables are not

damaged.

2. The terminals are intact,

secure, and free from

spark signs and rust.

Take measures

depending on the severity.

Appearance of

power distribution

components

Quarterly

Visual

observation

The appearance is intact.

Take measures

depending on the severity.

Operating

temperature and

humidity

Quarterly

Measure the

temperature

and humidity

using a point

thermometer.

Operating temperature:

–

°C to +40°C

Relative humidity: 5%

–

95% RH

Check that the air

conditioner and

dehumidifier in the

equipment room function

properly.

Dust on the

surface of the

PDU5000

Yearly

Check

whether there

is dust.

The white paper that you

use to wipe the equipment

is clean.

If the white paper is dirty,

clean the PDU5000.

Routine Maintenance

Symptom

Possible Causes

Troubleshooting Measures

The surge

protection function

fails.

•

The SPD circuit breaker is

not turned on.

•

The SPD ground cable is

not connected.

•

The surge protection

module is abnormal. The

SPD window is red.

•

Check that the SPD circuit breaker is turned

on.

•Check that the SPD ground cable is connected.

•

Replace the surge protection module.

The rear

-end

device power input

is abnormal.

•The switch trips abnormally.

•

The PDU5000 is faulty.

•

Use a multimeter to check whether there is a

short circuit. Turn on the switch again, and

check whether the system is overloaded.

•

Restart the PDU5000. If the PDU5000

is faulty,

replace it.

The PDU5000

does not report

faults, but has no

output voltage.

•

The output power cable is

not securely connected.

•

The output circuit breaker

is abnormal.

•

Check the output power cable connection.

•

Replace the circuit breaker.

Troubleshooting

Technical Specifications

Item

Specifications

Operating temperature –5°C to +40°C

Storage temperature –40°C to +70°C

Relative humidity 5%–95% RH (non-condensing)

Altitude ≤ 2000 m

Rated operating frequency 50 Hz

Rated operating voltage 220 V AC

Installation mode Installed inside a cabinet

Protection level IP20

Huawei Technologies Co., Ltd.

Huawei Industrial Base, Bantian, Longgang

Shenzhen 518129 People's Republic of China

www.huawei.com

Table des matières

Autres manuels Huawei Unité de contrôle

Huawei

Huawei MU509 Series Manuel utilisateur

Huawei

Huawei ME906s Manuel utilisateur

Huawei

Huawei V100R001C00 Manuel utilisateur

Huawei

Huawei EM660C EVDO Manuel utilisateur

Huawei

Huawei ME909u-523 Instructions d'installation

Huawei

Huawei MC509 Instructions d'installation

Huawei

Huawei RTN 380H Manuel utilisateur

Huawei

Huawei MU609 Instructions de montage

Huawei

Huawei ATOM GPS Manuel utilisateur

Huawei

Huawei SmartAX MA5600T Mode d’emploi

Huawei

Huawei MU509 Series Instructions d'installation

Huawei

Huawei MU709Gs-8 Manuel utilisateur

Huawei

Huawei MG323 Instructions d'installation

Huawei

Huawei UPS5000-E-400K-SMS Manuel utilisateur

Huawei

Huawei SmartAX MA5811S-AE08 Manuel utilisateur

Huawei

Huawei ME919Bs-567bN Manuel utilisateur

Huawei

Huawei MU609 Instructions d'installation

Huawei

Huawei SMU01C Manuel utilisateur

Huawei

Huawei EM770S Manuel utilisateur

Huawei

Huawei SmartLi-ESM-24020P1 Manuel utilisateur

Huawei

Huawei UPS5000-E Series Manuel utilisateur

Huawei

Huawei UPS5000-E Series Manuel utilisateur

Huawei

Huawei ME906A Instructions de montage

Huawei

Huawei VP9660 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur