HP Z Turbo Drive Quad Pro Manuel utilisateur
HP Z Turbo Drive Quad Pro installation
Printed in
*838785-002*
838785-002
© 2015 HP Development Company, L.P.
Linux® is the registered trademark of Linus
Torvalds in the U.S. and other countries.
Windows is a trademark of the Microsoft group
of companies.
The information contained herein is subject to
change without notice. The only warranties for
HP products and services are set forth in the
express warranty statements accompanying
such products and services. Nothing herein
should be construed as constituting an
additional warranty. HP shall not be liable for
technical or editorial errors or omissions
contained herein.
Second Edition: October 2015
First Edition: August 2015
Document Part Number: 838785-002
HP Z Turbo Drive Quad Pro installation
Introduction
This document describes how to install the HP Z Turbo Drive Quad Pro into the HP Z440, Z640, and Z840
series workstations.
Kit contents
●HP Z Turbo Drive Quad Pro
●LED cable
●Installation instructions
●Warranty information
Before you begin
To view QuickSpecs and determine the compatibility of this product with your HP computer, see
http://www.hp.com/go/productbulletin.
The minimum BIOS revision for the HP Z440, Z640, and Z840 Workstations is 1.62. If these requirements are
not met, the computer does not recognize the drive.
If you are installing an operating system image on the drive, remove all other storage devices. Install this
drive in the primary PCIe slot indicated for your workstation and install the operating system image before
installing additional HP Z Turbo Drives or HP Z Turbo Drive Quad Pros or reinstalling the other storage devices.
The preferred slots are noted in the installation instructions for each computer. If you will be using the drive
as a data drive, you do not need to remove the other storage devices.
Introduction 1
Warnings and cautions
WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of a
hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the risk of
injury from a hot component, enable the surface to cool before touching.
WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of an
electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed area
marked with this symbol.
WARNING! To reduce the risk of electric shock or damage to your equipment:
— Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
— Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.
— Disconnect power from the equipment by unplugging the power cord from the electrical outlet.
WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper
computer setup, posture, health, and work habits for computer users, and provides important electrical and
mechanical safety information. This guide is located at http://www.hp.com/ergo and on the documentation
CD (if one is included with the product).
WARNING! If a product is shipped in packaging marked with this symbol, , the product must always be
lifted by two persons to avoid personal injury due to product weight.
CAUTION: Static electricity can damage the electronic components of the computer. Before beginning these
procedures, be sure you discharge static electricity by briey touching a grounded metal object.
CAUTION: To prevent damage to the computer, observe the following Electrostatic Discharge (ESD)
precautions while performing the system parts removal and replacement procedures:
— Work on a static-free mat.
— Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body to
the ground.
— Create a common ground for the equipment you are working on by connecting the static-free mat, static
strap, and peripheral units to that piece of equipment.
NOTE: HP accessories are for use in HP computer products. They have been extensively tested for reliability
and are manufactured to high quality standards.
Installing additional M.2 modules in the HP Z Turbo Drive Quad
Pro
You can install up to four M.2 PCIe SSD modules in this drive. Load the modules from the cover hinge to the
PCIe edge connector in the following order.
TIP: Install all M.2 modules before installing the HP Z Turbo Drive Quad Pro assembly.
2 HP Z Turbo Drive Quad Pro installation
1. Open the drive cover.
a. Slide the latch to the left of the door to the left until the red area beneath the latch is fully exposed
(1).
b. Slide the right latch to the right and hold it (2).
c. While holding the right latch, press the center of the edge of the cover and lift it (3).
2. Loosen the two captive screws on the heat sink (1).
Installing additional M.2 modules in the HP Z Turbo Drive Quad Pro 3
3. Lift the heat sink to expose the M.2 modules (2).
NOTE: The drive comes with at least two M.2 modules preinstalled.
4. Remove the stando from the next M.2 slot.
4 HP Z Turbo Drive Quad Pro installation
5. Insert stando into the curve of the right edge of the M.2 module.
6. Slide the M.2 module into the connector (1) and then press down until the stando is aligned with the
embedded nut (2).
Installing additional M.2 modules in the HP Z Turbo Drive Quad Pro 5
7. Screw the stando into the nut.
8. Reinstall the heat sink (1) and tighten the captive screws (2).
Be sure that the tabs on the heat sink are under the metal pins and can rotate.
6 HP Z Turbo Drive Quad Pro installation
9. Close the cover (1) and slide the left latch to the right until no red is showing (2).
Installing additional M.2 modules in the HP Z Turbo Drive Quad Pro 7
Accessing the internal components of the computer
1. If you need help preparing the computer for this installation, consult the removal and replacement
procedures in the HP Customer Self Repair Services Media Library at http://www.hp.com/go/sml or in the
service guide for your computer at http://www.hp.com/support/manuals.
2. Power down the workstation, and then disconnect the power cord.
3. Power down all external devices, and then disconnect them from the workstation.
4. Remove the access panel by lifting up on the release latch and raising the panel from the chassis.
Installing the drive in an HP Z440 Workstation
If more than one of any of the following drives are to be installed in a system, a unique address for each drive
must be congured before installation:
●HP Z Turbo Drive
●HP Z Turbo Drive G2
●HP Z Turbo Quad Pro
For conguration instructions, see Installing multiple HP Z Turbo Drives or HP Z Turbo Quad Pro Drives
on page 14.
1. Press down on the two green PCI retention clips (1) located inside the workstation until they release,
and then rotate them down to raise the retention clamp (2).
8 HP Z Turbo Drive Quad Pro installation
Autres manuels pour Z Turbo Drive Quad Pro
1
Table des matières
Autres manuels HP Matériel informatique
HP
HP 4440B Manuel utilisateur
HP
HP Xw4600 - Workstation - 2 GB RAM Manuel utilisateur
HP
HP A5830AF-48G Manuel utilisateur
HP
HP 6600 FIP-20 Flex Instructions de montage
HP
HP A3550A - High Availability Disk Arrays Model 20 Storage... Manuel utilisateur
HP
HP 98640A Manuel d'installation et d'exploitation
HP
HP D7171A - NetServer - LPr Manuel utilisateur
HP
HP Adaptec ultra p2280a Manuel utilisateur
HP
HP AF079A Guide d'installation
HP
HP Compaq t5500 Manuel utilisateur
HP
HP E8402A Guide de dépannage
HP
HP CB001A Manuel utilisateur
HP
HP Xw4400 - Workstation - 2 GB RAM Manuel utilisateur
HP
HP 64782 Manuel utilisateur
HP
HP Smart Array P400 Instructions d'utilisation
HP
HP Z210 Series Manuel utilisateur
HP
HP C-CLASS BLADESYSTEM 409513-B21 Instructions d'utilisation
HP
HP QMH2572 8Gb FC HBA Instructions d'utilisation
HP
HP HP27110B Manuel d'installation et d'exploitation
HP
HP OmniBook 3100 Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
