HP HPE LSWM2XGT2PM Manuel utilisateur

HPE LSWM2XGT2PM Interface Card

(JH156A) User Guide

Part number: 5998-7834s

▌Introduction

Product

code HPE description Alias

JH156A HPE 5130/5510 10GBASE-T

2-port Module LSWM2XGT2PM

Overview

The LSWM2XGT2PM interface card provides two 1/10GBase-T

Ethernet ports.

Figure 1 LSWM2XGT2PM interface card

(1) 1/10GBase-T Ethernet

port LED

(2) 1/10GBase-T Ethernet port

(3) Captive screw (4) Ejector lever

NOTE:

The switch models that the LSWM2XGT2PM interface card are

applicable to may change over time. For the most recent list of

applicable switch models, contact HPE Support or marketing

staff.

1/10GBase-T Ethernet ports

Table 1 1/10GBase-T Ethernet port specifications

Item Specification

Connector type RJ-45

Port standard 1/10 Gbps full duplex, MDI/MDI-X

auto-sensing

Transmission medium

and max transmission

distance

•Category-6 unshielded twisted pair

cable: 55 m (180.45 ft)

•Category-6 shielded twisted pair

cable: 100 m (328.08 ft)

•Category-6A or above twisted pair

cable: 100 m (328.08 ft)

Compliance standard

•IEEE 802.3an

•IEEE 802.3ab

LEDs

Each 1/10GBase-T port on the LSWM2XGT2PM interface card has

an LED to indicate its operating status.

Table 2 describes LEDs for the QSFP+ ports.

Table 2 1/10GBase-T port LED descriptions

LED status Description

Steady green The port is operating at 10 Gbps, and a link is

present on the port.

Flashing green The port is sending or receiving data at 10

Gbps.

Steady yellow The port is operating at 1 Gbps, and a link is

present on the port.

LED status Description

Flashing yellow The port is sending or receiving data at 1 Gbps.

Off No link is present on the port.

NOTE:

The 1/10GBase-T port LEDs are not affected by the port mode

switching button on your switch. For more information about the

port mode switching button, see the installation guide of the

switch.

▌Installing and removing an interface card

CAUTION:

•Before you install or remove an interface card, wear an ESD

wrist strap and make sure the wrist strap makes good skin

contact and is reliably grounded.

•To avoid device damage, do not use excessive force when you

install or remove an interface card.

This example describes how to install and remove LSWM2XGT2PM

interface card on an HPE 5510 24G 4SFP+ HI 1-slot Switch

(JH145A).

Prepare the following tools before you install or remove an interface

card:

•Phillips screwdriver.

•Flat blade screwdriver.

•ESD wrist strap.

The installation tools are not provided with HPE devices. Prepare

them yourself.

Installing an interface card

Removing a filler panel

1. Use the Phillips screwdriver to remove the screw on the filler

panel in the target interface card slot, as shown by callout 1

in Figure 2.

2. Insert the flat blade screwdriver through the handle on the filler

panel to pull out the filler panel, as shown by callout 2 in Figure 2.

Figure 2 Removing a filler panel

NOTE:

Keep the removed screw and filler panel secure for future use.

Installing an LSWM2XGT2PM interface card

1. Unpack the interface card.

2. Insert the interface card slowly into the slot along the guide rails,

as shown by callout 1 in Figure 3.

3. Rotate inward the ejector lever as shown by callout 2 in Figure 3

until the interface card is in close contact with the switch.

4. Use the Phillips screwdriver to tighten the captive screw on the

interface card, as shown by callout 3 in Figure 3.

Figure 3 Installing an LSWM2XGT2PM interface card

Removing an interface card

CAUTION:

•Before you remove an interface card, remove the cable from it.

•After removing an interface card, if no new interface card is to

be installed, install the filler panel as soon as possible to

prevent dust and ensure good ventilation in the device.

Removing an LSWM2XGT2PM interface card

1. Prepare an anti-static bag.

2. Use the Phillips screwdriver to loosen the captive screw on the

interface card, as shown by callout 1 in Figure 4,

3. Rotate outward the ejector lever as shown by callout 2 in Figure 4.

4. Pull out the interface card slowly out the interface card slot as

shown by callout 3 in Figure 4.

5. Place the removed interface card in the anti-static bag.

Figure 4 Removing an LSWM2XGT2PM interface card

Verifying the installation

After the installation is complete, identify whether the interface card is

operating correctly according to the status of the 1/10GBase-T port

LEDs.

If the interface card fails to operate correctly, perform the following

steps:

1. Reinstall it following the installation procedures described in this

document.

2. If the problem persists, contact HPE Support.

▌Documentation

To access documentation and support services, go to the Hewlett

Packard Enterprise Support Center website:

www.hpe.com/support/hpesc

The information in this document is subject to change without notice.

BOM: 3101A0JL

Version: 6PW103

5998-7834s

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Matériel informatique

HP Rp5700 - Point of Sale System Instructions d'installation

HP 381513-B21 - Smart Array P800 Controller... Manuel utilisateur

HP 5930-4Slot Manuel utilisateur

HP Smart Array B140i Manuel utilisateur

HP QMH2672 Manuel utilisateur

HP ML570 - ProLiant - G2 Manuel utilisateur

HP E5000 Manuel utilisateur

HP Z210 Series Manuel utilisateur

HP StorageWorks XP128 Manuel utilisateur

HP 273914-B21 - Smart Array 6404/256 RAID... Manuel utilisateur

HP 64746 Manuel utilisateur

HP Xw8400 - Workstation - 4 GB RAM Manuel utilisateur

HP 10512 Instructions d'installation

HP AF079A Guide d'installation

HP MCS-200 Manuel utilisateur

HP A5830AF-48G Manuel utilisateur

HP D7171A - NetServer - LPr Manuel utilisateur

HP 705 Guide de démarrage rapide

HP Smart Array P400 Instructions d'utilisation

HP 3000 III Series Manuel utilisateur

HP Xw4600 - Workstation - 2 GB RAM Manuel utilisateur

HP Xw4400 - Workstation - 2 GB RAM Manuel utilisateur

HP AB479A Manuel utilisateur

HP E2416B Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur