Honeywell Midas-M Manuel utilisateur

3016M5000 Rev 01

MIDAS-M MULTI GAS TRANSMITTER

Fixed Single Point Extractive

Multi Gas Transmitter

QUICK

REFERENCE

GUIDE

Introduction

The Midas-M® is a Fixed Extractive Single Point with 4-in1 Multi Gas

Detector that draws a sample locally or from a remote point to a sensor

cartridge that is located inside the detector’s chassis. A wide range of toxic,

ﬂammable and oxygen gas sensor cartridges are available that enable

detection of gases used or generated in the Semiconductor and other

manufacturing industries.

NOTE: MidasM is shipped from the factory with the security function

disabled. We strongly recommend enabling this function for safe use of

the detector. To enable it, select Set up > Security and type an 8 character

password.

Safety

CAUTION

Failure to observe the following precautions can cause injury to persons or

damage to property:

• To minimize the risk of electrostatic charging, provide a suitable

ground connection, and install the equipment in such a way that no

accidental discharges occur.

• When MidasM reaches the end of its life, it should be disposed of by

local regulations.

• Do not use cleaning solvents or abrasives to clean the gas detector.

• Do not attempt to modify the product in any way from the manufactur-

er’s design or speciﬁcation. Warranty will be void and malfunction of

the gas detector may result.

• Use only genuine spare parts and accessories with MidasM. Malfunc-

tion may result if non-standard parts are used.

• MidasM is suitable for ordinary locations only and must not be in-

stalled in hazardous locations.

• Installation must be by the recognized standards of the appropriate

authority in the country concerned. For Europe, see EN6007914,

EN60079292, and EN6124114. For installations in North America,

the National Electrical Code (NFPA 70) should be strictly observed. All

the appropriate local and national regulations should be observed.

Sécurité

MISE EN GARDE

Le non-respect des précautions suivantes peut causer des blessures cor-

porelles ou des dégâts matériels:

• Pour minimiser les risques de charge électrostatique, veillez à ce que

la mise à la terre soit adéquate et installez l’équipement de manière à

éviter toute décharge accidentelle.

• Lorsque le MidasM arrive en ﬁn de vie, il doit être éliminé conformé-

ment à la réglementation locale.

• N’utilisez pas de solvants de nettoyage ou d’abrasifs pour nettoyer le

détecteur de gaz.

• Ne tentez en aucun cas de modiﬁer le produit à partir de la conception

ou des spéciﬁcations du fabricant. La garantie sera annulée et un

dysfonctionnement du détecteur de gaz pourrait en résulter.

• Utilisez uniquement des pièces de rechange et des accessoires d’orig-

ine avec MidasM. Un dysfonctionnement peut survenir si des pièces

non standard sont utilisées.

• MidasM ne convient qu’aux emplacements ordinaires et ne doit pas

être installé dans des endroits dangereux.

• L’installation doit être conforme aux normes reconnues par l’autorité

compétente du pays concerné. Pour l’Europe, voir EN6007914,

EN60079292 et EN6124114. Pour les installations en Amérique du

Nord, le code national de l’électricité (NFPA 70) doit être strictement

observé. Toutes les réglementations locales et nationales appropriées

doivent être observées.

Approvals

• Electrical UL/CSA/IEC/EN 610101

• EMC EN 50270

• ROHS

What’s in the Box

• 1 Transmitter device

• 2 Tubes (Large box only)

• 1 Quick Reference Guide

Overview

Mounting bracket assembly

Pump Module

Sensor cartridge

Main Module

Power LED

Alarm 1 LED

Alarm 2 LED

Fault LED

Selected channel number

indicator for menu operation

Device status icons

Bar graph for gas concentration display

Entry indicator for menu operation

Gas concentration

Unit

Gas name, menu, fault message

Buttons

Fault

Inhibit

Wireless Connected

Bluetooth Connected

Internal pump runningGas Calibration

in progress

Cancel

Device Status LED’s

Device Status Icons

Channel #1 Status

Channel #2 Status

Channel #3 Status

Channel #4 Status

Down

2 3 4

Mounting the Transmitter Device

Open the door

Remove two screws

Carefully pull main chassis forward

Drill two holes 2.2 in

• Partially screw the ﬁxings into the mounting surface.

• Place the mounting bracket assembly over the screws, so they pass

through the mounting holes and then slide down to locate in the slots.

• Tighten the screws to secure the mounting bracket assembly.

2 X

• Align the rounded corner at the lower of the main module with the sim-

ilar rounded corner at the bottom of the mounting bracket assembly

• Slide the main module backward while pushing the main module up

after connecting with a mounting bracket so that the PCB and con-

nector and tubes engage simultaneously.

Ensure the PCB, connector, and tubes are fully engaged by ﬁrmly push-

ing the main chassis horizontally backward on the mounting bracket

assembly. DO NOT PUSH ON THE LCD AS THIS MAY DAMAGE IT.

• Align the two ﬁxing screws located at the bottom of the chassis with

the screw threads on the mounting bracket assembly.

• Tighten the screws to secure the chassis to the mounting bracket

assembly.

2 X

Mounting the Transmitter Device

Remove the internal packing card securing the pump. Failure to

remove this packing will result in damage to the MidasM detector.

Mounting the Transmitter Device

Electrical Installation

Access for the electrical wires to the terminal module is made via the PG16

cable gland located at the bottom of the mounting bracket assembly. The

cable gland can be removed and replaced with a suitable conduit ﬁtting if

required. The wire routing of a typical installation is shown in the following

diagram.

4-20mA

Controlled

Current Source

SWITCH

EXT

INT

SWITCH

Internal

Power

Loads

Relay

Contact

Terminals

4-20mA Analog Output

Switches (4 Channels)

24Vdc Power Terminals

4-20mA Analog Output

Switches (4 Channels)

RJ45 Connector

Optimal

Relays

Connector

Power Switch

Cable Gland

The terminals used are suitable for conductors of 24 to 14 AWG (0.5 to

1.8mm Dia.). We recommend using the 16 AWG (1.5 mm Dia.) conductors.

If Power over Ethernet (PoE) is used to power the device, then 24 VDC

power must not also be connected to the device, (or conversely if 24 VDC

is used to power the MidasM, then electrical power via the Ethernet port

must not be applied). Failure to observe this requirement may cause dam-

age to the gas detection system and will not be covered by the standard

warranty.

When connecting the wires, ensure that the power switch is in the off

position.

Autres manuels pour Midas-M

Table des matières

Autres manuels Honeywell Émetteur

Honeywell

Honeywell K595 Manuel utilisateur

Honeywell

Honeywell oneWireless XYR 6000 Manuel utilisateur

Honeywell

Honeywell OELD Manuel utilisateur

Honeywell

Honeywell STT850 SMARTLINE Manuel utilisateur

Honeywell

Honeywell SmartLine SLN 700 Series Manuel utilisateur

Honeywell

Honeywell SmartLine ST700 Manuel utilisateur

Honeywell

Honeywell oneWireless XYR 6000 Manuel utilisateur

Honeywell

Honeywell SmartLine STIW400 Manuel utilisateur

Honeywell

Honeywell 5800MICRA Manuel utilisateur

Honeywell

Honeywell ADEMCO 5878 Instructions de montage

Honeywell

Honeywell STT850 Series Manuel utilisateur

Honeywell

Honeywell XYR 5000 Series Manuel utilisateur

Honeywell

Honeywell NOTIFIER AFL-RM Manuel utilisateur

Honeywell

Honeywell ADEMCO 5804-2 Manuel utilisateur

Honeywell

Honeywell STD110 Manuel utilisateur

Honeywell

Honeywell 5820L - Slim Line Wireless Door/Window... Instructions de montage

Honeywell

Honeywell 5834-4 Series Instructions de montage

Honeywell

Honeywell ST 3000 Manuel utilisateur

Honeywell

Honeywell 5817CBXT Manuel utilisateur

Honeywell

Honeywell STT850 SMARTLINE Manuel utilisateur

Honeywell

Honeywell 5822T Manuel utilisateur

Honeywell

Honeywell OELD Manuel utilisateur

Honeywell

Honeywell 5815 - Ademco - Wireless Door Manuel utilisateur

Honeywell

Honeywell XYR 5000 Series Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manuel utilisateur