Honeywell XYR 5000 Series Manuel utilisateur

Wireless Dual Analog Input

Interface Transmitter

User Manual

Americas

900 MHz ISM Band

XYR 5000 Line

34-XY-25-04

Rev. 8

July 2012

Honeywell Process Solutions Wireless Dual Analog Input Interface Transmitter

Rev. 8 User Manual I

July 2012

FCC Certification

• This product is a frequency hopping RF transceiver module for the 900 MHz

ISM band, designed to meet FCC 15.247, and is used in industrial control and

monitoring applications.

• The antenna is factory installed and MUST NOT be removed or modified by the

user.

Wireless Dual Analog Input Interface

Transmitter

Models WI551 and WI552

Versions 1.70 or later

Important Information to the User !

• Changes or modifications not expressly approved by the manufacturer may void

the user’s authority to operate the equipment.

• This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: 1) this device may not cause harmful interference, and

2) this device must accept any interference received, including interference that

may cause undesired operation.

• This device is for mobile and fixed use only (not portable or body-worn). A

separation distance of 20 cm must be maintained at all times between the antenna

and the body of the user and bodies of nearby persons.

• This device has been designed to operate with an antenna having a maximum

gain of 9 dBd. Antenna having a higher gain is strictly prohibited per regulations

of Industry Canada. The required antenna impedance is 50 Ohms.

• To reduce potential radio interference to other users, the antenna type and its gain

should be so chosen that the equivalent isotropically radiated power (EIRP) is not

more than that required for successful communication.

• The installer of this radio equipment must ensure that the antenna is located or

pointed such that it does not emit RF field in excess of Health Canada limits for

the general population; consult Safety Code 6, obtainable from Health Canada’s

website www.hc-sc.gc.ca/rpb.

Honeywell Process Solutions

1860 West Rose Garden Lane

Phoenix, Arizona, 85027

Rev. 8 – July 2012

While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied warranties of merchantability and

fitness for a particular purpose and makes no express warranties except as may be stated in its written agreement with and for its customers.

In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and specifications in this document

are subject to change without notice.

Honeywell®and TotalPlant®are U.S. registered trademarks Of Honeywell International Inc.

Other brand or product names are trademarks of their respective owners.

Honeywell Process Solutions Wireless Dual Analog Input Interface Transmitter

II User Manual Rev. 8

July 2012

About This Document

Revision Notes

The following list provides notes concerning all revisions of this document.

Contacts

The following is a list of Honeywell contacts for including Internet World Wide Web, Telephone, Fax and Email.

For Asia Pacific, Europe, North and South Americas

Doc ID Rel ID Date Notes

34-XY-25-04 Rlse. 0 12/03 1st issue of document.

34-XY-25-04 Rev. 2 06/04 Reformatted layout, updated technical information.

34-XY-25-04 Rev. 1 02/04 2nd issue of document.

34-XY-25-04 Rev. 3 09/04 Updated maintenance section

34-XY-25-04 Rev. 3b 04/05 Removed Output Section, added Rev C Control Drawing.

34-XY-25-04 Rev. 4 12/05 Updated Control drawings.

34-XY-25-04 Rev. 5 08/06 Version 1.70 of the software.

34-XY-25-04 Rev. 6 08/08 Updated dimensions

34-XY-25-04 Rev. 7 05/12 Battery updates

34-XY-25-04 Rev. 8 07/12 Battery updates

Honeywell Process Solutions Wireless Dual Analog Input Interface Transmitter

Sales and Service

For application assistance, current specifications, pricing, or name of the nearest Authorized Distributor, contact one of the offices below.

ASIA PACIFIC

(TAC)

hfs-tac-

support@honeywell.com

Australia

Honeywell Limited

Phone: +(61) 7-3846 1255

FAX: +(61) 7-3840 6481

Toll Free 1300-36-39-36

Toll Free Fax:

1300-36-04-70

China – PRC - Shanghai

Honeywell China Inc.

Phone: (86-21) 5257-4568

Fax: (86-21) 6237-2826

Singapore

Honeywell Pte Ltd.

Phone: +(65) 6580 3278

Fax: +(65) 6445-3033

South Korea

Honeywell Korea Co Ltd

Phone: +(822) 799 6114

Fax: +(822) 792 9015

EMEA

Honeywell Process Solutions,

Phone: + 80012026455 or +44

(0)1202645583

FAX: +44 (0) 1344 655554

Email: (Sales)

sc-cp-apps-

salespa62@honeywell.com

(TAC)

hfs-tac-

support@honeywell.com

NORTH AMERICA

Honeywell Process Solutions,

Phone: 1-800-423-9883

Or 1-800-343-0228

Email: (Sales)

ask-ssc@honeywell.com

(TAC)

hfs-tac-

support@honeywell.com

SOUTH AMERICA

Honeywell do Brasil & Cia

Phone: +(55-11) 7266-1900

FAX: +(55-11) 7266-1905

Email: (Sales)

ask-ssc@honeywell.com

(TAC)

hfs-tac-

support@honeywell.com

Honeywell Process Solutions Wireless Dual Analog Input Interface Transmitter

Rev. 8 User Manual III

July 2012

Table of Contents

Section 1: Introduction____________________________________ 1

1.1: Using This Manual 1

1.2: About the Device 2

1.3: Unpacking 2

1.4: Software Compatibility 2

Section 2: Quick Start_____________________________________ 3

Section 3: Installation_____________________________________ 4

3.1: Mechanical Installation 4

3.1.1: Transmitter Positioning 4

3.2: Testing Communications 7

3.2.1: Transmitter RSSI Diagnostics 7

3.2.2: Link Test 8

3.3: Electrical Installation 13

3.3.1: Electrical Specifications 13

3.3.2: Wiring the Voltage/Current Input 13

3.3.3: Wiring the Input Switches 14

Section 4: General Configuration __________________________ 15

4.1: Transmitter Displayed Messages 15

4.1.1: The Read-Only Sequence 15

4.2: Overall Configuration Menu Map 16

4.3: Setting the Transmitter Tag Name 16

4.4: Setting a User Password 17

4.5: Resetting All Transmitter Settings 17

Section 5: Configuring the RF Communications ______________ 18

5.1: RF Channel Selection 18

5.2: RF Baud Rate Selection 19

5.3: RF Identification Selection 19

Section 6: Configuring the Sampling and Transmission Rates___ 21

6.1: Selecting the Normal Transmission Rate 21

6.1.1: Configure the Normal Transmission Rate from the Transmitter 22

6.1.2: Configure the Normal Transmission Rate Using WMT 22

6.2: Selecting the Normal Sampling Rate 23

6.2.1: Selecting the Normal Sampling Rate from the Transmitter 24

6.2.2: Configure the Normal Sampling Rate Using WMT 24

6.3: Selecting the Abnormal Transmission Rate 25

6.3.1: Configure the Abnormal Transmission Rate from the Transmitter 25

6.3.2: Configure the Abnormal Transmission Rate Using WMT 26

6.4: Selecting the Abnormal Sampling Rate 27

6.4.1: Configure the Abnormal Sampling Rate from the Transmitter 27

6.4.2: Configure the Abnormal Sampling Rate Using WMT 28

6.5: Setting the Smart Rate Threshold 29

6.5.1: Configure the Smart Rate Using WMT 29

6.6: Selecting the Normal Upper and Lower Values 30

6.6.1: Configure the Upper and Lower Limits from the Transmitter 30

6.6.2: Configure the Upper and Lower Limits Using WMT 31

6.7: Selecting Rates, Thresholds, and Deadbands via the Software 32

Honeywell Process Solutions Wireless Dual Analog Input Interface Transmitter

IV User Manual Rev. 8

July 2012

Honeywell Process Solutions Wireless Dual Analog Input Interface Transmitter

Section 7: Configuring the Process Variable _________________ 33

7.1: Selecting the Units of Measure 33

7.2: Setting a Measurement Offset 34

7.3: Trimming the Measurement 34

7.4: Entering a 22-Point Curve 35

Section 8: Maintaining the Transmitter _____________________ 36

8.1: Changing the Battery 36

Section 9: Technical Specifications _________________________ 37

Dimensioned Mechanical Drawing 39

Intrinsically Safe Installation Control Drawing 40

Appendix A: Navigating User Menus _______________________ 45

Appendix B: Transmitter Displayed Message Definitions ______ 46

Appendix C: Transmitter Menu Map_______________________ 47

Honeywell Process Solutions Wireless Dual Analog Input Interface Transmitter

Rev. 8 User Manual 1

July 2012

Section 1: Introduction

1.1: USING THIS MANUAL This manual is designed to assist in installing, operating, and maintaining

Honeywell Model WI551 and WI552 Dual Analog Input Interface Trans-

mitters. The manual is broken into sections as follows:

Section 2: Quick Start

This section summarizes what must be done in order to get the device in-

stalled, configured, and in operation quickly. However, it does not provide

detailed or how-to information to perform the tasks outlined.

Section 3: Installation

This section explains how to correctly wire the Voltage/Current loops,

Input Switches, and ground the Transmitter. Also covered in this section

are mechanical installation considerations; such as Transmitter placement.

Section 4: General Configuration

In this section, general configuration options such as password protection,

and selecting a user password are discussed. Also covered, is the setting of

a Transmitter tag name, resetting of all Transmitter settings, and a discus-

sion on the various messages that are displayed on the Transmitter LCD.

Section 5: Configuring the RF Communications

This section covers the setup of the Transmitter RF Communications that

allow the Transmitter to achieve communication with the Base Radio.

Parameters discussed are the Transmitter RF ID, the RF channel setting,

and Baud Rate.

Section 6: Configuring the Sampling and Transmission Rates

This section aids the user in selecting the amount of time between each

sample of the process, and the time between each transmission of this

sample to the Base Radio. Also discussed is the use of setting an abnormal

threshold in which sampling and transmission times may change during a

period when the process variable is within the abnormal region.

Section 7: Configuring the Process Variable

This section helps the user in the selection of engineering units, and dis-

cusses setting a measurement offset and trimming the process measure-

ment.

Section 8: Maintaining the Transmitter

This section explains how the Transmitter should be cared for once it has

been placed into service and how to change the battery.

Section 9: Technical Specifications

This section explains the technical specifications that are associated with

this device such as power characteristics, accuracy, and operating charac-

teristics.

Honeywell Process Solutions Wireless Dual Analog Input Interface Transmitter

2User Manual Rev. 8

July 2012

1.2: ABOUT THE DEVICE The Honeywell Dual Analog Input Transmitter is a reliable Radio Fre-

quency (RF) transceiver coupled with a dual-channel analog input sensor

that can be used to monitor a variety of processes in hazardous and hard-to

-reach areas.

The time and expense of running wires often makes it difficult to measure

parameters that have an economic impact on your plant operation, but the

Dual Analog Input Transmitter allows you to quickly and accurately

monitor those devices at a fraction of the cost, which gives you bigger and

faster returns on your instrumentation investments.

The Transmitters communicate in a secure, digital protocol over a band of

frequencies from 902 MHz to 928 MHz. This data communication tech-

nique has been the backbone of the military’s secure communications pro-

tocols for many years. These devices require no wires, permits or licenses,

and they are easily set up and installed right out of the box.

You can use this device for long term monitoring in remote locations, for

short-term data gathering on process conditions, or to quickly test the eco-

nomic viability of a new installation.

The purpose of this manual is to help you install and maintain your Hon-

eywell Dual Analog Input Transmitter. BEFORE setting up and installing

the Transmitter please setup and configure the Base Radio.

1.3: UNPACKING Remove the Packing List and check off the actual equipment received. If

you have any questions about your shipment, please call your Honeywell

Representative. Upon receipt of the shipment, inspect the container for

any signs of damage in transit. Especially take note of any evidence of

rough handling. Report any apparent damage immediately to the shipping

agent.

Please note that sometimes units are assembled with accessories when

shipped. Inspect the shipment carefully if you think that something is

missing. This is rare, as we take considerable care to pack units for ship-

ment, but it does sometimes happen. Please give us a call and we may be

able to resolve this matter quickly over the phone.

NOTE

The carrier will not honor any claims for damage unless all shipping ma-

terials are saved for their examination. If you find any damage while you

are examining and removing the contents, save the packing material and

the carton.

1.4: SOFTWARE

COMPATIBILITY

Software for Honeywell is revised periodically. Internal device software

may contain portions that are not compatible with previous versions of the

Wireless Management Toolkit software.

To ensure software compatibility, Wireless Management Toolkit software

version 1.70.138 or later must be used. If you believe you are experienc-

ing software compatibility issues please call Honeywell Technical Support

at 800-423-9883 or email ACE@Honeywell.com.

Honeywell Process Solutions Wireless Dual Analog Input Interface Transmitter

Rev. 8 User Manual 3

July 2012

This section summarizes what must be done in order to get the device in-

stalled, configured, and in operation quickly. However, it does not provide

detailed or how-to information to perform the tasks outlined.

Section 2: Quick Start

1. Place the Transmitter in the desired location of operation.

Note: Trimming of the measurement may be necessary before the

device can be placed in service. If trimming is required, perform

steps 1 and 6-15 prior to placing the device in service.

2. Wire the analog input(s) as shown in the top left figure.

3. Wire the input switches as shown in the bottom left figure (optional).

4. Ground the Transmitter via grounding screw provided in enclosure.

5. Close the enclosure and secure enclosure via set screw.

6. Turn on the Transmitter by simultaneously pressing and holding the

ENTER and NEXT buttons.

7. Set the RF CHAN setting equal to the Base Radio’s RF Channel.

8. Set the BAUD RT setting equal to the Base Radio’s Baud Rate.

9. Set the RF ID number to be a unique value between 1 and 100.

10. Select the normal transmission rate.

11. Select the normal sampling rate.

12. Select the abnormal transmission rate.

13. Select the abnormal sampling rate.

14. Set the normal upper and lower values.

15. Select the engineering measurement units.

If the “RF OFF” message is being displayed on the Transmitter LCD, per-

form the following:

• Set the RF CHAN setting equal to the Base Radio’s RF

Channel.

If a “NO RF” message is being displayed on the Transmitter LCD, check

the following:

• Is the Transmitter set to the above listed settings?

• Is the Base Radio on?

• Do the Transmitter and Base Radio settings match? (See

Section 5 of Transmitter and Base Radio User Guides)

• Are the Base Radio and Transmitters unable to communicate

due to obstructions or distance? (See Section 3.1.1: Trans-

mitter Positioning)

Warning! If the Transmitters have been running for an extended period

of time with no signal from the Base Radio (the Base Radio is off or not

present), the Transmitters will only search for the Base Radio every one

hour or so. Turning the Transmitters off and back on will cause them to

begin searching immediately.

Warning !!

Honeywell Process Solutions Wireless Dual Analog Input Interface Transmitter

4User Manual Rev. 8

July 2012

Section 3: Installation

3.1: Mechanical Installation

Warning

During installation do not apply force to the in-

strument housing or antenna. Use a proper wrench

for all installations. Failure to use correct installa-

tion procedures can cause damage to the Transmit-

ter.

In this section mechanical installation instructions are discussed for the

various setup capabilities of the Dual Analog Input Transmitter.

Each Honeywell Dual Analog Input Transmitter is a rugged device which

provides optimal performance when installed with careful consideration.

Installation practices greatly affect the life that you can expect from your

Honeywell Dual Analog Input Transmitter. The main considerations for

installation are covered below.

Give careful consideration to the environment where you will be installing

your instrument. Avoid installations that expose the device to excess

temperature, high vibration, considerable shock, or exposure to dripping

condensate or corrosive materials. Also avoid installing the device in an

unserviceable location.

Most often these problems can be avoided with some thought at the time

of installation. The practices noted below are generally recommended, but

they can only act as a guideline and cannot cover all possible variations.

The final installation must be made at your discretion and approval. You

must be the judge of the actual installation.

Dimensioned mechanical drawings for aid in mechanical installation are

located in Section 9: Technical Specifications

Correct positioning of the Transmitter will ensure the best performance of

the device. When planning the positioning of the Transmitters, there are a

few parameters that must be paid attention to:

3.1.1: Transmitter Positioning

• The top of the Transmitter should point upwards. The bottom

of the Transmitter should NOT point directly at the Base

Radio and the Transmitter LCD should point away from the

Base Radio.

• All Transmitters should maintain an approximate spacing of

at least six feet apart from one another. Should you need to

put Transmitters closer than six feet, please see Section

3.1.1.1 entitled “Technique for Close Positioning of

Transmitters”.

• The line of sight range between a Transmitter and Base

Radio is 2000 feet at the 19.2K baud rate setting. Note that

this range is reduced by the amount of RF noise present,

obstructions, and the material properties of the obstruction.

• Only place the Transmitter in ambient operating

temperatures of -40°F to 185°F (-40°C to 85°C).

Figure 3.1 gives examples of incorrect setups according to the previously

mentioned parameters.

Autres manuels pour XYR 5000 Series

Table des matières

Autres manuels Honeywell Émetteur

Honeywell

Honeywell SmartLine STIW400 Manuel utilisateur

Honeywell

Honeywell STT850 SMARTLINE Manuel utilisateur

Honeywell

Honeywell Midas S2 Manuel utilisateur

Honeywell

Honeywell SmartLine ST700 Manuel utilisateur

Honeywell

Honeywell ST 3000 Manuel utilisateur

Honeywell

Honeywell ADEMCO 5801 Instructions de montage

Honeywell

Honeywell XNX Manuel utilisateur

Honeywell

Honeywell APT2000 Series Manuel utilisateur

Honeywell

Honeywell ST 3000 Manuel utilisateur

Honeywell

Honeywell SMV800 Manuel utilisateur

Honeywell

Honeywell SmartLine Manuel utilisateur

Honeywell

Honeywell 5814 - Ademco Ultra-small Wireless... Manuel utilisateur

Honeywell

Honeywell oneWireless XYR 6000 Manuel utilisateur

Honeywell

Honeywell PWTA40 Series Manuel utilisateur

Honeywell

Honeywell ST 800 Series Manuel utilisateur

Honeywell

Honeywell oneWireless XYR 6000 Manuel utilisateur

Honeywell

Honeywell MCE 2 Manuel utilisateur

Honeywell

Honeywell ADEMCO 5878 Instructions de montage

Honeywell

Honeywell ADEMCO 5817 Instructions de montage

Honeywell

Honeywell oneWireless XYR 6000 Manuel utilisateur

Honeywell

Honeywell Satellite XT 9602-0400 FTT Manuel utilisateur

Honeywell

Honeywell SmartLine ST700 Manuel utilisateur

Honeywell

Honeywell STT850 SMARTLINE Manuel utilisateur

Honeywell

Honeywell oneWireless XYR 6000 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manuel utilisateur