Honeywell 5817CBXT Manuel utilisateur

The 5817CBXT is a universal contact-monitoring transmitter

that can be used with household and commercial fire and

burglary-initiating devices such as door/window contacts,

motion and glassbreak detectors, sprinkler water flow

switches, tamper switches, post indicator valves, manual

pull stations and remote duct detectors. Upon activation, it

emits an RF signal to a control panel, sending a burglary or

fire alarm to a central station.



input loops (zones)



supervised and typically used for

high-priority alarm reporting such

as commercial fire or burglary

(reporting transmission every

four seconds)



normally closed reed switch used in

conjunction with magnet



closed household burglary loop. All

three loops may be used.



loop contains two tamper switches

to protect the 5817CBXT



commercial fire and burglary

1. Remove the transmitter cover by

inserting the flat blade of a small

screwdriver into the pry-off slot at the

bottom end of the unit (on the right

side closest to the cover’s decorative

ribs and twisting).

2. Disengage the supplied mounting

plate from the unit by inserting the

blade of a small screwdriver into the

mounting plate release hole (see

Diagram 2) and pushing the locking

tab out (see Diagram 1). Slide the

mounting plate downward along the

case back.

Note: For this application, the

alignment guide strip along one edge

of the mounting plate serves no

function and may be broken away,

if desired.

3. If concealed wiring is to be used,

feed the wires through the concealed

wiring entry hole on one corner of the

plate (surface wiring is mentioned in

step 5 below).

4. Install the mounting plate, with its

caseholding posts pointing up, in the

location selected as described in the

installation instructions. Use the two

flat-head screws supplied. Note: To

ensure proper operation of the unit’s

back tamper (when it is separated

from the mountain plate), the screws

must be anchored to a wall stud or

other solid wood material.

5. Set the DIP switch (after the

control panel has enrolled the

transmitter’s input ID’s) for the

desired primary loop characteristics,

as described in the table on the

following page.

Features

MOuNtING

5817CBXt





- 1-9/16" W x 3-1/2" H x 1-3/16" D

(40mm x 89mm x 30mm)









 

 

 

 

 

1610







5817CBXt Wireless Commercial Transmitter

5817CBXt











Honeywell Security Products Americas

2 Corporate Center Dr. Suite 100





1.800.467.5875

www.honeywell.com

Figure 1. Mounting Plate

Figure 2. Case Back

Figure 3. 5817CBXT Transmitter, Top Cover Removed

Figure 1. Mounting Plate

Figure 2. Case Back

Figure 3. 5817CBXT Transmitter, Top Cover Removed

Figure 1. Mounting Plate

Figure 2. Case Back

Figure 3. 5817CBXT Transmitter, Top Cover Removed



installations, multiple initiating devices may be used as long as the devices all service the same function such as door/window contacts, motion or



14-22AWG wire.

Notes: a. In order for the control panel to enroll the transmitter, the DIP switches must be Set to OFF-ON-ON-OFF (see Diagram 2).

b. The auxiliary loops are not affected by the DIP switch settings.

Wiring Connections

Connect the loop wiring to the unit’s terminals before installing the battery (see Diagram 2).

Notes: a. Primary loop 1 is a supervised loop and must have an end-of-line (EOL) resistor (470K ohms, supplied) placed across the sensor.

Additionally, for primary loop 1, a contact device may not be installed more than 20 feet from the transmitter.

b. If loop 2 is not going to be used, the magnet is not necessary.

c. If loop 3 is not going to be used, no connection is needed across its terminals. For UL household burglary and ﬁre installations, the loop 3

contact device (if used) may not be more than 3 feet from the transmitter.

Primary Loop Options Table

Switch

Setting

DIP Switch Position

On Repeating transmission (every 4 sec.) upon primary loop fault use high priority alarm, such as ﬁre.

Off Single transmission per primary loop change-of-state.

Table des matières

Autres manuels Honeywell Émetteur

Honeywell

Honeywell XNX Guide de l'utilisateur

Honeywell

Honeywell ST 3000 Instructions d'installation et d'utilisation

Honeywell

Honeywell 5878 - Wireless Wall Transmitter Manuel utilisateur

Honeywell

Honeywell HVB16TPTX Manuel utilisateur

Honeywell

Honeywell STT850 Series Manuel utilisateur

Honeywell

Honeywell STD110 Manuel utilisateur

Honeywell

Honeywell Midas S2 Manuel utilisateur

Honeywell

Honeywell XNX Manuel utilisateur

Honeywell

Honeywell 5819AP Instructions de montage

Honeywell

Honeywell ADEMCO 5805-6 Instructions de montage

Honeywell

Honeywell STT850 SMARTLINE Manuel utilisateur

Honeywell

Honeywell ST 3000 Manuel utilisateur

Honeywell

Honeywell oneWireless XYR 6000 Manuel utilisateur

Honeywell

Honeywell XYR 5000 Series Manuel utilisateur

Honeywell

Honeywell 5834-4 Series Instructions de montage

Honeywell

Honeywell K595 Manuel utilisateur

Honeywell

Honeywell oneWireless XYR 6000 Manuel utilisateur

Honeywell

Honeywell 5800 Mini Manuel utilisateur

Honeywell

Honeywell SmartLine SLG 700 Manuel utilisateur

Honeywell

Honeywell STT850 SMARTLINE Manuel utilisateur

Honeywell

Honeywell ST 3000 Manuel utilisateur

Honeywell

Honeywell 5802mn2 - Ademco Wireless Panic Manuel utilisateur

Honeywell

Honeywell 5800MICRA Manuel utilisateur

Honeywell

Honeywell Fema Moduflex F Series Manuel

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manuel utilisateur