Hirschmann GREYHOUND GRS1020 Manuel utilisateur

Installation GRS1020/1120/1030/1130

Release

01/2017

Technical support

https://hirschmann-support.belden.eu.com

User Manual

Installation

GREYHOUND Switch

GRS1020/1120/1030/1130

GRS 1020

GRS 1030

GRS 1120

GRS 1130

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

InstallationGRS1020/1120/1030/1130

Installation GRS1020/1120/1030/1130

Release

01/2017 3

Contents

Safety instructions 5

About this Manual 14

Legend 14

1 Description 15

1.1 General device description 15

1.2 Device name and product code 16

1.3 Combination options 20

1.4 Device views 21

1.4.1 Front view 21

1.4.2 Rear view 22

1.5 Power supply 23

1.5.1 Supply voltage with the characteristic value C 23

1.5.2 Supply voltage with the characteristic value M 23

1.6 Ethernet ports 23

1.6.1 Gigabit combo port 23

1.6.2 10/100 Mbit/s twisted pair port 25

1.6.3 100 Mbit/s F/O port (optional) 25

1.7 Display elements 26

1.7.1 Device state 26

1.7.2 Port status 27

1.7.3 Media module status 28

1.8 Management interfaces 29

1.8.1 V.24 interface (external management) 29

1.8.2 USB interface 29

1.9 Signal contact 30

2 Installation 31

2.1 Checking the package contents 31

2.2 Installing and grounding the device 31

2.3 Installing an SFP transceiver (optional) 35

2.4 Connecting the terminal blocks 36

2.4.1 Supply voltage with the characteristic value C 36

2.4.2 Supply voltage with the characteristic value M 37

2.4.3 Signal contact 38

2.5 Mounting a media module (optional) 39

4Installation GRS1020/1120/1030/1130

Release

01/2017

2.6 Operating the device 40

2.7 Connecting data cables 40

2.8 Filling out the inscription label 40

3 Making basic settings 41

4 Monitoring the ambient air temperature 42

5 Maintenance and service 43

6Disassembly 44

6.1 Removing the device 44

6.2 Removing an SFP transceiver (optional) 44

6.3 Removing a media module (optional) 45

7 Technical data 46

A Further Support 58

Installation GRS1020/1120/1030/1130

Release

01/2017 5

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning the device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

Correct usage

Only use the device for those purposes specified in the catalog and in the

technical description. Only operate the device with external devices and

components that are recommended and permitted by the manufacturer.

The proper and safe operation of this product depends on proper handling

during transport, proper storage, assembly and installation, and

conscientious operation and maintenance procedures.

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

6Installation GRS1020/1120/1030/1130

Release

01/2017

Supply voltage

The supply voltage is electrically isolated from the housing.

Every time you connect the electrical conductors, make sure that the

following requirements are met:

The power supply conforms to overvoltage category I or II.

The power supply has an easily accessible disconnecting device

(e.g., a switch or a plug). This disconnecting device is clearly

identified. So in the case of an emergency, it is clear which

disconnecting device belongs to which power supply cable.

The electrical wires are voltage-free.

The ground screw on the back of the device is connected to the

protective conductor.

Supply with AC voltage:

A fuse is located in the outer conductor of the power supply.

The neutral conductor is on ground potential at both voltage inputs.

Otherwise, a fuse is also located in the neutral conductor.

Regarding the properties of this fuse:

See “General technical data” on page 46.

Supply with DC voltage:

A fuse suitable for DC voltage is located in the plus conductor of the

power supply.

The minus conductor is on ground potential. Otherwise, a fuse is

also located in the minus conductor.

Regarding the properties of this fuse:

See “General technical data” on page 46.

Supply with DC voltage: the fuse is suitable for a DC voltage.

If the neutral conductor (AC) or the negative conductor (DC) is not

grounded: there is a fuse in each of the two wires.

Supply with AC voltage:

The wire diameter of the power supply cable is at least 0.75 mm²

(North America: AWG18) on the supply voltage input.

Supply with DC voltage:

The wire diameter of the power supply cable is at least 1 mm²

(North America: AWG16) on the supply voltage input.

The cross-section of the protective conductor is the same size as

or bigger than the cross-section of the power supply cables.

The cables used are permitted for the temperature range of the

application case.

Relevant for North America:

For use in Class 2 circuits, the copper wire conforms to class 1,

140/167 °F or 167 °F (60/75 °C or 75 °C).

Installation GRS1020/1120/1030/1130

Release

01/2017 7

Verify that the electrical installation meets locally or nationally

applicable safety regulations.

Use undamaged parts.

Internal fuses are triggered only in the case of a detected error in the

device. In case of damage or malfunction of the device, turn off the

supply voltage and return the device to the plant for inspection.

Only switch on the device when the housing is closed.

First connect the ground screw on the back of the device with the

protective conductor before you set up the other connections. When

removing the connections, you remove the protective conductor last.

For supply voltage connections with protective conductor connection:

First connect the protective conductor before connecting the wires for

the supply voltage.

If your device comprises a 2nd supply voltage connection of this type:

First connect the protective conductor before connecting the wires for

the supply voltages.

Shielded ground

The shielded ground wire of the twisted pairs cables is connected to the

front panel as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shield braiding.

WARNING

ELECTRIC SHOCK

Start connecting the electrical wires only if all the above safety

requirements are fulfilled.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

8Installation GRS1020/1120/1030/1130

Release

01/2017

Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

Keep the ventilation slits free to ensure good air circulation.

Make sure there is at least 3.94 inches (10 cm) of space in front of the

ventilation slits of the housing.

Do not touch the housing during operation or shortly after switching off

the device. Hot surfaces can cause injury.

Mount the device horizontally in a cabinet or vertically on a flat surface.

Operating the device as a table unit is inadmissible.

See “Installing and grounding the device” on page 31.

Operating the device in the maximum surrounding air temperature and

stacking devices: When installing the device, make sure there is at

least one free rack space (approx. 5 cm) above the device, because

heat is discharged via the housing of the device.

If you are operating the device in a 19" switch cabinet: install

sliding/mounting rails for supporting the weight of the device.

WARNING

ELECTRIC SHOCK

Never insert sharp objects (small screwdrivers, wires, etc.) into the inside of

the device.

Never insert sharp objects (small screwdrivers, wires, etc.) into the

connection terminals for electric conductors, and do not touch the terminals.

Install this device solely in a switch cabinet or in an operating site with

restricted access, to which maintenance staff have exclusive access.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

WARNING

FIRE HAZARD

Install the device in a fire protected shell if you are mounting it vertically.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

Installation GRS1020/1120/1030/1130

Release

01/2017 9

Operating conditions

Operate the device at the specified ambient temperature (temperature of

the ambient air at a distance of 2 inches (5 cm) from the device) and at

the specified relative humidity exclusively.

When you are selecting the installation location, make sure you

observe the climatic threshold values specified in the technical data.

Use the device in an environment with a maximum pollution degree

that complies with the specifications in the technical data.

Relevant for use in explosion hazard areas (Hazardous

Locations, Class I, Division 2):

The relay connections are to be installed and used within their entity

parameters as per Control Drawing 000192283DNR. Details see the next

two pages.

Avertissement - Risque d'explosion - Ne pas débrancher tant que le

circuit est sous tension à moins que l'emplacement soit connu pour ne

contenir aucune concentration de gaz inflammable.

Avertissement - Risque d'explosion - La substitution de tout composant

peut rendre ce matériel incompatible pour une utilisation en classe I,

division 2.

10 Installation GRS1020/1120/1030/1130

Release

01/2017

CONTROL DRAWING - GREYHOUND series for use in HAZARDOUS LOCATIONS

Class I, Division 2, Groups A, B, C, D

Document No.:

000192283DNR

Rev.: 0 Page 1/2

The earth conductor must be

at least of the same wire size

(mm² or AWG) as the supply

conductors.

Any GREYHOUND-GRS1xxx device

Class I, Division 2

Groups A, B, C, D

Hazardous Location

1RQLQFHQGLYH¿HOGZLULQJSDUDPHWHUV

THE USB POWER SUPPLY CONTACTS DEPEND

ON THE FOLLOWING PARAMETERS: *)

Front view

Back view

Ordinary location,

non-hazardous area,

non-explosive atmosphere

VOC ISC CaLa

9 $ 10 μF 10 μH

Vmax Imax CaLa

9 90 mA 3 nF 1 μH

1RQLQFHQGLYH¿HOGZLULQJSDUDPHWHUV

THE RELAY TERMINALS DEPEND ON THE

FOLLOWING PARAMETERS: *)

FAULT contacts

USB pin 1

USB pin 4

Autres manuels pour GREYHOUND GRS1020

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hirschmann Changer

Hirschmann

Hirschmann RS1 Series Manuel

Hirschmann

Hirschmann RSPE 30 Manuel utilisateur

Hirschmann

Hirschmann MACH 3001 Manuel

Hirschmann

Hirschmann GECKO 4TX Manuel utilisateur

Hirschmann

Hirschmann RS2-4R Manuel

Hirschmann

Hirschmann SPIDER 5TX Manuel

Hirschmann

Hirschmann OCTOPUS OS20 Manuel utilisateur

Hirschmann

Hirschmann RS20 series Manuel utilisateur

Hirschmann

Hirschmann OCTOPUS 8M Series Manuel utilisateur

Hirschmann

Hirschmann RSPE30 Manuel utilisateur

Hirschmann

Hirschmann MACH104-20TX-F Series Manuel utilisateur

Hirschmann

Hirschmann RS20 series Manuel utilisateur

Hirschmann

Hirschmann MAR1042 Manuel utilisateur

Hirschmann

Hirschmann 943 686-003 Manuel utilisateur

Hirschmann

Hirschmann RH1-CX+ Manuel utilisateur

Hirschmann

Hirschmann MACH1000 Series Manuel utilisateur

Hirschmann

Hirschmann GREYHOUND GRS1020 Manuel utilisateur

Hirschmann

Hirschmann OS20-001000T5T5TAFUHB Manuel utilisateur

Hirschmann

Hirschmann BATOne Manuel utilisateur

Hirschmann

Hirschmann CS30 Manuel utilisateur

Hirschmann

Hirschmann BRS20-0400 Series Manuel utilisateur

Hirschmann

Hirschmann MACH4000 Series Manuel utilisateur

Hirschmann

Hirschmann RSP 25 Manuel utilisateur

Hirschmann

Hirschmann OCTOPUS OS20 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur