Hirschmann OCTOPUS OS20 Manuel utilisateur

Installation OS20/OS30

Release

06/2015

Technical Support

https://hirschmann-support.belden.eu.com

User Manual

Installation

IP67 Switch

OS20 / OS30

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD/DVD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

OS20/OS30 039 727-001-03-0615 1.7.15

Installation OS20/OS30

Release

06/2015 3

Contents

Safety instructions 5

About this Manual 9

Legend 9

1 Description 10

1.1 General device description 10

1.2 Device name and product code 11

1.3 Device views 13

1.3.1 Front view 13

1.3.2 Interfaces 13

1.4 Power supply 14

1.5 Ethernet ports 15

1.5.1 10/100 Mbit/s twisted pair port 15

1.5.2 100 Mbit/s F/O port 15

1.5.3 1000 Mbit/s F/O port 16

1.5.4 Pin assignments 16

1.6 Display elements 17

1.6.1 Device state 18

1.6.2 Port state 18

1.7 Management interfaces 19

1.7.1 V.24 interface (external management) 19

1.7.2 ACA interface (ACA21-M12) 20

1.8 “FAULT” signal contact 21

2 Installation 22

2.1 Checking the package contents 22

2.2 Installing and grounding the device 23

2.2.1 Mounting on a flat surface 23

2.2.2 Grounding the device 23

2.3 Wiring the connectors for supply voltage and signal contact 24

2.4 Operating the device 25

2.5 Connecting data cables 25

2.5.1 Twisted Pair ports 25

2.5.2 Optical fiber ports 25

3 Making basic settings 26

4Installation OS20/OS30

Release

06/2015

4 Monitoring the ambient air temperature 27

5 Maintenance and service 28

6Disassembly 29

6.1 Removing the device 29

7 Technical data 30

A Further Support 37

Installation OS20/OS30

Release

06/2015 5

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning the device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Certified usage

Use the product only for the application cases described in the

Hirschmann product information, including this manual.

Operate the product only according to the technical specifications.

See “Technical data” on page 30.

Connect to the product only components suitable for the requirements

of the specific application case.

Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

At ambient temperatures > 140 °F (60 °C):

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

6Installation OS20/OS30

Release

06/2015

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

Grounding the device

The device is grounded via the separate ground screw.

See figure 3 on page 14.

Use a wire diameter for the ground conductor that is no smaller than

the diameter of the supply voltage connection, however of at least

0.5 mm² (AWG20).

Ground the device before connecting any other cables.

Disconnect the grounding only after disconnecting all other cables.

Shielding ground

The overall shield of a connected shielded twisted-pair cable is connected

to the metal housing as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Supply voltage

The devices are designed for operation with safety extra-low voltage.

Connect only SELV circuits with voltage restrictions in line with IEC/EN

60950-1 to the supply voltage connections and signal contacts.

The supply voltage is electrically isolated from the housing.

Use a power supply cable which is suitable for the voltage, the current

and the physical load.

Hirschmann recommends a wire diameter of 0.5 mm² to 0.75 mm²

(AWG20 to AWG18).

Installation OS20/OS30

Release

06/2015 7

Relevant for North America:

The device may only be connected to a Class 2 supply voltage that fulfills

the requirements of the National Electrical Code, Table 11(b). If the

voltage is being supplied redundantly (two different voltage sources), the

combined supply voltages must fulfill the requirements of the National

Electrical Code, Table 11(b).

Relevant for North America: For use in Class 2 circuits.

Only use copper wire/conductors of class 1, 75 °C (167 °F).

Relevant for installations under UL conditions:

Supply voltage: 19.2 V DC to 28.8 V DC

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2004/108/EC (EMC)

Directive of the European Parliament and the council for standardizing the

regulations of member states with regard to electromagnetic

compatibility.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

The device can be used in the industrial sector.

Interference immunity: EN 61000-6-2

Emitted interference: EN 55022

You find more information on technical standards here:

“Technical data” on page 30

The assembly guidelines provided in these instructions must be strictly

adhered to in order to observe the EMC threshold values.

8Installation OS20/OS30

Release

06/2015

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take

appropriate measures.

LED or laser components

LED or LASER components according to IEC 60825-1 (2014):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

FCC note:

This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Appropriate testing has established that this device fulfills the

requirements of a class A digital device in line with part 15 of the FCC

regulations.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can also radiate these

frequencies. If it is not installed and used in accordance with this

operating manual, it can cause radio transmission interference. The use

of this device in a residential area can also cause interference, and in this

case the user is obliged to cover the costs of removing the interference.

Recycling note

After usage, this device must be disposed of properly as electronic waste,

in accordance with the current disposal regulations of your county, state,

and country.

Installation OS20/OS30

Release

06/2015 9

About this Manual

The “Installation” user manual contains a device description, safety

instructions, a description of the display, and the other information that you

need to install the device.

The following manuals are available as PDF files on the CD/DVD supplied:

Installation user manual

Basic Configuration user manual

Redundancy Configuration user manual

User Manual Industry Protocols

Reference manual for the graphical user interface

Command Line Interface reference manual

The Industrial HiVision network management software provides you with

additional options for smooth configuration and monitoring:

ActiveX control for SCADA integration

Auto-topology discovery

Browser interface

Client/server structure

Event handling

Event log

Simultaneous configuration of multiple devices

Graphical user interface with network layout

SNMP/OPC gateway

Legend

The symbols used in this manual have the following meanings:

Listing

Work step

Subheading

10 Installation OS20/OS30

Release

06/2015

1 Description

1.1 General device description

You can choose from between a wide range of variants. You have the option

to set up your device individually based on different criteria:

Number of ports

Transmission speed

Types of connectors

Temperature range

Supply voltage range

Certifications

The OS20-... device variants are IP67 Switches without gigabit Ethernet

ports and with ten 10/100 Mbit/s Ethernet ports.

The OS30-... device variants are IP67 Switches with two gigabit Ethernet

ports (1000 Mbit/s) and eight 10/100 Mbit/s Ethernet ports.

The OS20/OS30 devices are designed for the special requirements of

industrial automation. They meet the relevant industry standards, provide

very high operational reliability, even under extreme conditions, and also

long-term reliability and flexibility.

The devices allow you to set up switched and routed industrial Ethernet

networks that conform to the IEEE 802.3 standard.

The devices work without a fan.

You have the option of choosing various media to connect to the terminal

devices and other network components:

twisted pair cable

multimode F/O

singlemode F/O

The redundancy concept allows the network to be reconfigured quickly.

There are convenient options for managing the device. Administer your

devices via:

a Web browser

SSH

Telnet

HiDiscovery (Software for putting the device into operation)

network management software (e.g. Industrial HiVision)

a V.24 interface (locally on the device)

Autres manuels pour OCTOPUS OS20

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hirschmann Changer

Hirschmann

Hirschmann MSP30 Manuel utilisateur

Hirschmann

Hirschmann GECKO 4TX Manuel utilisateur

Hirschmann

Hirschmann MSP30 Manuel utilisateur

Hirschmann

Hirschmann RSPL 20 Manuel utilisateur

Hirschmann

Hirschmann MACH1000 Series Manuel utilisateur

Hirschmann

Hirschmann MACH1040 Manuel utilisateur

Hirschmann

Hirschmann OS20-001000T5T5TAFUHB Manuel utilisateur

Hirschmann

Hirschmann RH1-TP Manuel

Hirschmann

Hirschmann MACH4000 Series Manuel utilisateur

Hirschmann

Hirschmann MACH102 Series Manuel utilisateur

Hirschmann

Hirschmann Power MICE Manuel utilisateur

Hirschmann

Hirschmann PowerMICE MS4128 Manuel utilisateur