Hirschmann OCTOPUS 8M Series Manuel utilisateur

Installation OCTOPUS 8M/16M/24M/OS32

Release

06/2018

Technical Support

https://hirschmann-support.belden.com

User Manual

Installation

IP65/67 Switch

OCTOPUS 8M..., OCTOPUS 16M..., OCTOPUS 24M...,

OCTOPUS OS32...

U :24 - 48 V CLASS2 I :0,5 - 0,1 A

in in

OCTOPUS 8M

OCTOPUS 24M-Train-BP

OCTOPUS 24M

OCTOPUS 16M-Train-BP

OCTOPUS 16M

OCTOPUS 8M

OCTOPUS OS32-081602O6O6...

OCTOPUS OS32-081602T6T6...

P1 P2 RM FAULT

V.2 4

ACA

Power

Managed

ETHERNET Switch

x y

OCTOPUS

OS32

Produktcode

IP-ADDRESS

FunctionPin

N.C.

GND

+48V DC

FunctionPin

FAULT 3

TP-Ports

P1 P2 RM FAULT

V.2 4

ACA

Power

Managed

ETHERNET Switch

x y

OCTOPUS

OS32

Produktcode

IP-ADDRESS

FunctionPin

N.C.

GND

+48V DC

FunctionPin

FAULT 3

TP-Ports

FunctionPin

1 MDX1+

2 MDX1 -

3 MDX0+

4 MDX0 -

5 MDX2+

6 MDX2 -

7 MDX3 -

8 MDX3+

Managed IP67

ETHERNET Switch

FunctionPin

N.C.

GND

FunctionPin

+24V DC

+24V DC FAULT

U :24 - 48 V CLASS 2 I : 0,27 - 0,14 A

in in

OCTOPUS 16M-Train-BP

FunctionPin

TD +

RD +

TD −

RD −

Bypass Function:

Power off

Port 4

Port 8

Managed IP67

ETHERNET Switch

FunctionPin

N.C.

GND

FunctionPin

+24V DC

+24V DC FAULT

U :24 - 48 V CLASS 2 I : 0,27 - 0,14 A

in in

OCTOPUS 24M-Train-BP

FunctionPin

TD +

RD +

TD −

RD −

Bypass Function:

Power off

Port 4

Port 8

U :24 - 48 V CLASS2 I :1,1 - 0,2 A

in in

OCTOPUS 8M

U :24 - 48 V CLASS2 I :1,4 - 0,25 A

in in

OCTOPUS 8M

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Installation OCTOPUS 8M/16M/24M/OS32 11.06.2018

Installation OCTOPUS 8M/16M/24M/OS32

Release

06/2018 3

Contents

Safety instructions 5

About this Manual 10

Legend 11

1 Description 12

1.1 General device description 12

1.2 Description of the device variants 13

1.2.1 Devices without Power over Ethernet 13

1.2.2 Devices with Power over Ethernet 14

1.3 Power supply 15

1.4 PoE voltage (optional) 16

1.5 Ethernet ports 16

1.5.1 10/100 Mbit/s twisted pair port 16

1.5.2 10/100 Mbit/s PoE port 17

1.5.3 10/100/1000 Mbit/s twisted pair port 17

1.5.4 100/1000 Mbit/s F/O port 18

1.5.5 Pin assignments 18

1.6 Display elements 19

1.6.1 Device state 19

1.6.2 Port Status 20

1.7 Management interfaces 20

1.7.1 V.24 interface (external management) 20

1.7.2 ACA interface (ACA21-M12) 21

1.8 “FAULT” signal contact 22

2 Installation 23

2.1 Checking the package contents 23

2.2 Installing an SFP transceiver (optional) 24

2.3 Installing and grounding the device 25

2.3.1 Mounting on a flat surface 25

2.3.2 Grounding the device 25

2.4 Wiring the connectors for supply voltage and signal contact 26

2.5 Connecting the PoE voltage (optional) 27

2.6 Operating the device 27

2.7 Connecting data cables 28

4Installation OCTOPUS 8M/16M/24M/OS32

Release

06/2018

3 Making basic settings 29

4 Monitoring the ambient air temperature 30

5 Maintenance and service 31

6Disassembly 32

6.1 Removing the device 32

6.2 Unmounting an SFP transceiver (optional) 33

7 Technical data 34

7.1 General technical data 34

7.2 Dimension drawings 36

7.3 EMC and immunity 39

7.4 Network range 40

7.5 Power consumption/power output 41

8 Scope of delivery, order numbers and

accessories 42

9 Underlying technical standards 45

A Further support 46

Installation OCTOPUS 8M/16M/24M/OS32

Release

06/2018 5

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning the device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Certified usage

Use the product only for the application cases described in the

Hirschmann product information, including this manual.

Operate the product only according to the technical specifications.

See “Technical data” on page 34.

Connect to the product only components suitable for the requirements

of the specific application case.

Operational environment:

On the inside of vehicles

On the inside of buildings

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow this instruction can result in death, serious injury, or

equipment damage.

6Installation OCTOPUS 8M/16M/24M/OS32

Release

06/2018

Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

At ambient temperatures > 140 °F (60 °C):

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

To preserve the suitability of your device for IP65/67, proceed as

follows:

Remove the provided transport protection caps and the transport

protection screws from the device.

Seal unused sockets and plugs with the type of protection screws

which you can order separately.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

Grounding the device

The housing is grounded via the separate ground screw on the bottom left

of the front panel.

Use a wire diameter for the ground conductor that is no smaller than

the diameter of the supply voltage connection, however of at least

0.5 mm² (AWG20).

Ground the device before connecting any other cables.

Disconnect the grounding only after disconnecting all other cables.

Shielding ground

The overall shield of a connected shielded twisted-pair cable is connected

to the metal housing as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Installation OCTOPUS 8M/16M/24M/OS32

Release

06/2018 7

Supply voltage

The devices are designed for operation with safety extra-low voltage.

Connect only SELV circuits with voltage restrictions in line with IEC/EN

60950-1 to the supply voltage connections and signal contacts.

The supply voltage is electrically isolated from the housing.

Only use voltage supply cables with the permitted diameter specified

by the manufacturer of the right angled cable socket.

Relevant for North America:

Devices without Power-over-Ethernet (PoE) may only be connected to

a supply voltage of class 2 that fulfills the requirements of the National

Electrical Code, Table 11(b). If the voltage is being supplied

redundantly (two different voltage sources), the combined supply

voltages must fulfill the requirements of the National Electrical Code,

Table 11(b).

Relevant for North America: For use in Class 2 circuits.

Only use copper wire/conductors of class 1, 75 °C (167 °F).

E marking

(Relevant for OCTOPUS 8M-8PoE, OCTOPUS 8M-6PoE, OCTOPUS

16M-8PoE, OCTOPUS 24M-8PoE)

The labeled devices comply with the regulations contained in the following

European directive(s):

72/245/EEC

Council Directive on the approximation of the laws of the Member States

relating to the suppression of radio interference produced by sparkignition

engines fitted to motor vehicles.

2009/19/EC

Commission Directive amending, for the purposes of its adaptation to

technical progress, Council Directive 72/245/EEC relating to the radio

interference (electromagnetic compatibility) of vehicles.

Devices with an approval are labeled with the E type-approval mark.

(Relevant for OCTOPUS OS32...)

Regulation No. 10 of the Economic Commission for Europe of the United

Nations (UN/ECE): Devices with an approval are labeled with the

E type approval mark.

Note: For use in connection with a suitable type approved power supply

only.

8Installation OCTOPUS 8M/16M/24M/OS32

Release

06/2018

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2014/30/EU (EMC)

Directive of the European Parlament and of the Council on the

harmonisation of the laws of the Member States relating to

electromagnetic compatibility.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

www.hirschmann.com

The device can be used in the industrial sector.

Interference immunity: EN 61000-6-2

Emitted interference: EN 55032

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take

appropriate measures.

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

LED or laser components

Relevant for OCTOPUS OS32-08xx02O6O6...:

LED or LASER components according to IEC 60825-1 (2014):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

Installation OCTOPUS 8M/16M/24M/OS32

Release

06/2018 9

FCC note:

This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Appropriate testing has established that this device fulfills the

requirements of a class A digital device in line with part 15 of the FCC

regulations.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can also radiate these

frequencies. If it is not installed and used in accordance with this

operating manual, it can cause radio transmission interference. The use

of this device in a residential area can also cause interference, and in this

case the user is obliged to cover the costs of removing the interference.

Recycling note

After usage, this device must be disposed of properly as electronic waste,

in accordance with the current disposal regulations of your county, state,

and country.

10 Installation OCTOPUS 8M/16M/24M/OS32

Release

06/2018

About this Manual

The “Installation” user manual contains a device description, safety

instructions, a description of the display, and the other information that you

need to install the device.

The documentation for your device is made up of the following documents:

General safety instructions

Installation user manual

Basic Configuration user manual

Redundancy Configuration user manual

Reference manual for the graphical user interface

Command Line Interface reference manual

You find these manuals as PDF files on the Internet on the Hirschmann

product pages (www.hirschmann.com).

The HiVision Network Management software provides you with additional

options for smooth configuration and monitoring:

ActiveX control for SCADA integration

Auto-topology discovery

Browser interface

Client/server structure

Event handling

Event log

Simultaneous configuration of multiple devices

Graphical user interface with network layout

SNMP/OPC gateway

Autres manuels pour OCTOPUS 8M Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hirschmann Changer

Hirschmann

Hirschmann RS20 series Manuel utilisateur

Hirschmann

Hirschmann OCTOPUS 8M Series Manuel utilisateur

Hirschmann

Hirschmann CS30 Manuel utilisateur

Hirschmann

Hirschmann RH1-TP Manuel

Hirschmann

Hirschmann Dragon PTN Manuel utilisateur

Hirschmann

Hirschmann RS1 Series Manuel

Hirschmann

Hirschmann MACH 4000 Series Manuel utilisateur

Hirschmann

Hirschmann RSPM20-4Z64Z6 Series Manuel utilisateur

Hirschmann

Hirschmann OCTOPUS OS20 Manuel utilisateur

Hirschmann

Hirschmann RS20 series Manuel utilisateur

Hirschmann

Hirschmann ETHERNET IP67 Instructions d'utilisation et d'installation

Hirschmann

Hirschmann MACH4000 Series Manuel utilisateur

Hirschmann

Hirschmann MACH4000 Series Manuel utilisateur

Hirschmann

Hirschmann PAT TRS 05 / PATB3 Guide de l'utilisateur

Hirschmann

Hirschmann GREYHOUND GRS1020 Manuel utilisateur

Hirschmann

Hirschmann MACH1040 Manuel utilisateur

Hirschmann

Hirschmann MACH 3001 Manuel

Hirschmann

Hirschmann RSPE30 Manuel utilisateur

Hirschmann

Hirschmann SPIDER 5TX Manuel

Hirschmann

Hirschmann RS20 series Manuel utilisateur

Hirschmann

Hirschmann SPIDER 5TX Manuel

Hirschmann

Hirschmann MACH 100 Manuel utilisateur

Hirschmann

Hirschmann GECKO 4TX Manuel utilisateur

Hirschmann

Hirschmann Power MICE Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur