Graco Dispensit 1052 Guide de dépannage
Cycle Detection and Luer Lock Outlet Shown
3A0231E
EN
Operation - Maintenance
Dispensit
1052
Patented meter and dispense system for precise one-component micro-dispensing. Not for
use in explosive atmospheres.
2000 psi (14 MPa, 138 bar) Maximum Outlet Fluid Working Pressure
Metal Sleeves: 1200 psi (8 MPa, 83 bar) Maximum Material Inlet Pressure
Plastic Sleeves: 400 psi (2.8 MPa, 28 bar) Maximum Material Inlet Pressure
100 psi (0.7 MPa, 7 bar) Maximum Air Working Pressure
110°F (43°C) Maximum Ambient Temperature
150°F (65°C) Maximum Operating Temperature
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
23A0231E
Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Isocyanate Conditions . . . . . . . . . . . . . . . . . . . . . . 5
Material Self-ignition . . . . . . . . . . . . . . . . . . . . . . . 5
Moisture Sensitivity of Isocyanates . . . . . . . . . . . . 5
Changing Materials . . . . . . . . . . . . . . . . . . . . . . . . . 5
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Optional Cycle Detection Spool Sensors . . . . . . . 6
Component Identification . . . . . . . . . . . . . . . . . . . . 7
Typical System Configurations . . . . . . . . . . . . . . 7
Typical Feed System Components . . . . . . . . . . . 8
Typical Feed System Components (continued) . . 9
Metering Valve . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Typical Installation . . . . . . . . . . . . . . . . . . . . . . . 11
Valve Mounting Diagram . . . . . . . . . . . . . . . . . . 12
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Adjusting the Shot Size . . . . . . . . . . . . . . . . . . . . 14
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Sequence of Operation . . . . . . . . . . . . . . . . . . . 15
Pressure Relief Procedure . . . . . . . . . . . . . . . . . . 16
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Rebuild . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Graco Ohio Standard Warranty . . . . . . . . . . . . . . 22
Graco Ohio Information . . . . . . . . . . . . . . . . . . . . 22
Warnings
3A0231E 3
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-
tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back
to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where
applicable.
WARNING
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just
a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.
• Do not point gun at anyone or at any part of the body.
• Do not put your hand over the dispense outlet.
• Do not stop or deflect leaks with your hand, body, glove, or rag.
• Follow Pressure Relief Procedure in this manual, when you stop dispensing and before cleaning,
checking, or servicing equipment.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
• Read MSDS’s to know the specific hazards of the fluids you are using.
• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
• Always wear impervious gloves when spraying or cleaning equipment.
• If this equipment is used with isocyanate material, see additional information on isocyanates in Iso-
cyanate Conditions Section of this manual.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic
fumes, burns, and hearing loss. This equipment includes but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by the fluid and solvent manufacturer
•Gloves
• Hearing protection
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent
fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop
cloths (potential static arc).
• Keep work area free of debris, including solvent, rags and gasoline.
• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes
are present.
• Ground all equipment in the work area. See Grounding instructions.
• Use only grounded hoses.
• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment
until you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
Warnings
43A0231E
ELECTRIC SHOCK HAZARD
This equipment must be grounded. Improper grounding, setup, or usage of the system can cause elec-
tric shock.
• Turn off and disconnect power cord before servicing equipment.
• Use only grounded electrical outlets.
• Use only 3-wire extension cords.
• Ensure ground prongs are intact on power and extension cords.
• Do not expose to rain. Store indoors.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
• Do not leave the work area while equipment is energized or under pressure. Turn off all equipment
and follow the Pressure Relief Procedure in this manual when equipment is not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-
facturer’s replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
MOVING PARTS HAZARD
Moving parts can pinch or amputate fingers and other body parts.
• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,
follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.
PLASTIC PARTS CLEANING SOLVENT HAZARD
Use only compatible water-based solvents to clean plastic structural or pressure-containing parts. Many
solvents can degrade plastic parts and cause them to fail, which could cause serious injury or property
damage. See Technical Data in this and all other equipment instruction manuals. Read fluid and solvent
manufacturer’s warnings.
WARNING
Isocyanate Conditions
3A0231E 5
Isocyanate Conditions
Material Self-ignition
Moisture Sensitivity of
Isocyanates
ISO will react with moisture (such as humidity) to form
small, hard, abrasive crystals, which become sus-
pended in the fluid. Eventually a film will form on the sur-
face and the ISO will begin to gel, increasing in viscosity.
If used, this partially cured ISO will reduce performance
and the life of all wetted parts.
NOTE: The amount of film formation and rate of crystal-
lization varies depending on the blend of ISO, the
humidity, and the temperature.
To prevent exposing ISO to moisture:
• Always use a sealed container with a desiccant
dryer in the vent, or a nitrogen atmosphere. Never
store ISO in an open container.
• Keep the ISO lube pump reservoir (if installed) filled
with Graco Throat Seal Liquid (TSL), Part 206995.
The lubricant creates a barrier between the ISO and
the atmosphere.
• Use moisture-proof hoses specifically designed for
ISO, such as those supplied with your system.
• Never use reclaimed solvents, which may contain
moisture. Always keep solvent containers closed
when not in use.
• Always lubricate threaded parts with ISO pump oil
or grease when reassembling.
Changing Materials
• When changing materials, flush the equipment mul-
tiple times to ensure it is thoroughly clean.
• Always clean the fluid inlet strainers after flushing.
• Check with your material manufacturer for chemical
compatibility.
Spraying or dispensing materials containing isocya-
nates creates potentially harmful mists, vapors, and
atomized particulates.
Read material manufacturer’s warnings and material
MSDS to know specific hazards and precautions
related to isocyanates.
Prevent inhalation of isocyanate mists, vapors, and
atomized particulates by providing sufficient ventila-
tion in the work area. If sufficient ventilation is not
available, a supplied-air respirator is required for
everyone in the work area.
To prevent contact with isocyanates, appropriate per-
sonal protective equipment, including chemically
impermeable gloves, boots, aprons, and goggles, is
also required for everyone in the work area.
Some materials may become self-igniting if applied
too thickly. Read material manufacturer’s warnings
and material MSDS.
Grounding
63A0231E
Grounding
This product must be grounded. In the event of an elec-
trical short circuit, grounding reduces the risk of electric
shock by providing an escape wire for the electric cur-
rent.
Metering valve: attach ground wire from grounding lug
to true earth ground. See Component Identification
starting on page 7.
Fluid hoses: use only electrically conductive hoses.
Feed system components: attach ground wire from
grounding lug to true earth ground. See feed system
manual for grounding points.
Fluid supply container: follow local code.
Solvent pails used when flushing: follow local code.
Use only conductive metal pails, placed on a grounded
surface. Do not place the pail on a nonconductive sur-
face, such as paper or cardboard, which interrupts
grounding continuity.
Overview
This single-component meter and dispense device
accurately meters liquid and semi-paste materials.
The machine is ideal for a single-component application
requiring very small and precisely mixed shots.
The ratio of the pneumatic cylinder area to pump shaft
area provides the adjustable pressure intensification
needed to move the separate liquids through the needle
with a flow rate suitable for production requirements.
The complete system is enclosed. See Sequence of
Operation on page 15.
Optional Cycle Detection
Spool Sensors
The spool sensors are magnetic reed switches and must
be connected to an electrical control. An LED on the
switch illuminates to indicate the shifting of the spool.
Component Identification
3A0231E 7
Component Identification
Typical System Configurations
FIG. 1
R
GREEN
GREEN
YELLOW
YELLOW
0
TIMER
DISPENSE
Liquid Control
R
PRESSURE
SYSTEM
REG-1 REG-2
AUXILIARY
PRESSURE
G-1 G-2
OFF
ON
PB-1
SW-1/PL-1
TR-1
HAND
OFF
SW-2
POWER
AUTO START
Valve
Controls
Top View of Controls
System shown with optional 4104A controls
Component Identification
83A0231E
Typical Feed System Components
FIG. 2
DO NOT SERVICE WITHOUT
REMOVING AIR PRESSURE AND
WEARING SAFETY GLASSES.
WARNING
F
200
psi
0
20 oz Cartridge Feed
with Mounting Post
5 Gallon Pail Cover
with Diaphragm Pump
1 Gallon Ram
and Pump
5 Gallon Pail Cover
with Diaphragm
Pump and Agitator
5 Gallon Ram and
11:1 Transfer Pump
5 Gallon Pail Cover
with Diaphragm
Pump
5 Gallon Pail Cover
with 5:1 Transfer
Pump
Component Identification
3A0231E 9
Typical Feed System Components (continued)
FIG. 3
R
0
12
8
4
psi
30
22
19
15
26
R
0
12
8
4
psi
30
22
19
15
26
5 Gallon Tank with Diaphragm Pump and Stand 5 Gallon Tank with 5:1 Pump and Stand
10 Gallon Tank with Diaphragm Pump, Agitator,
Vacuum, and Stand
10 Gallon Tank with 5:1 Pump, Agitator, Vacuum,
and Stand
Component Identification
10 3A0231E
Metering Valve
FIG. 4
GREEN
GREEN
YELLOW
0 43218765 21095634 987
YELLOW
Key:
A Material Inlet
C Grounding Lug
D Spool
E Metering Rod
F Oil Cup Retaining Block
G Extend Air Inlet
H Retract Air Inlet
J Dispense Air Inlet
K Reload Air Inlet
L Extend Air Flow Adjustment
Knob
M Retract Air Flow Adjustment
Knob
S Shot Size Locking Ring
T Shot Size Adjuster
Z Needle
T
S
H
G
E
M
KJ
F
DA
L
C
Z
Autres manuels pour Dispensit 1052
1
Table des matières
Autres manuels Graco Instrument de mesure
Graco
Graco ProMix 2KE Manuel d'utilisation et d'entretien
Graco
Graco PM8 Manuel utilisateur
Graco
Graco 244075 Manuel d'utilisation
Graco
Graco 234576 Manuel d'utilisation
Graco
Graco ProControl 1KE Plus Manuel d'utilisation
Graco
Graco 121325 Manuel d'utilisation
Graco
Graco EFR Manuel d'utilisation
Graco
Graco G250 Manuel de la liste des pièces
Graco
Graco FLOW METERS S3000 Manuel utilisateur
Graco
Graco 255348 Manuel utilisateur
Graco
Graco Accu-Shot 233807 Manuel de la liste des pièces
Graco
Graco SDMM8 Manuel utilisateur
Graco
Graco ProControl 1KE Manuel de la liste des pièces
Graco
Graco XDI12 Manuel utilisateur
Graco
Graco HG6000 Manuel de référence technique
Graco
Graco PM8 Guide de configuration
Graco
Graco PD44 Manuel utilisateur
Graco
Graco IM5 Fiche technique
Graco
Graco Accu-Shot 233807 Manuel utilisateur
Graco
Graco 215474 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur