Graco Pulse TEK 811 Guide de configuration

3A8551E

Installation, Operation, and Service

Pulse® Level Cellular

Tank Level Monitor

Measures the distance between the device and the surface of the fluid to determine the volume of fluid

within a tank. For use only with Pulse Level. Intended fluids: oil, diesel, waste oil, automatic transmission

fluid (ATF), kerosene, anti-freeze, windshield washer solution, waste water, and DEF. For professional use

only. Not suitable for tank overfill protection.

Not approved for use in explosive atmospheres or hazardous (classified) locations.

Part No. Model Description

Radio

Approvals Model Approvals

25T461 TEK 811 Pulse Level Cellular

North America

FCC, IC

133620 TEK 811 Pulse Level Cellular

International

CE, RCM

Important Safety Instructions

Read all warnings and instructions in this

manual and in all related Pulse manuals

before using the equipment. Save all

instructions.

WARNING

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not alter or modify equipment. Alterations or

modifications may void agency approvals and

create safety hazards.

• Make sure all equipment is rated and approved for

the environment in which you are using it.

• Use equipment only for its intended purpose. Call

your distributor for information.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the

work area to help prevent serious injury, including

eye injury, hearing loss, and inhalation of toxic fumes.

This Tank Level Monitor (TLM) contains FCC ID XMR

201707 BG96. This device complies with Part 15 of the

FCC Rules. Operation is subject to the following two

conditions:

• This device may not case harmful interference.

• This device must accept any interference received,

including interference that may cause undesired

operation.

Installation

2 3A8551E

Installation

Set Up

Level Software

Navigate to URL: level.gracopulse.com

This device requires access to a cellular network to

work, and can be activated in Pulse Level. Refer to

Pulse Level terms of service in the About section of the

software.

After creating user, organization, branch and site,

navigate to Devices (located in the upper right corner of

the screen). Associate the device to your organization

by entering the serial number. When you create a tank

for the site, the device will be assignable.

Assign the TLM serial number to a tank in Pulse Level.

Activation

1. Hold the magnet (supplied) to the Hot Spot directly

under the LED to activate the device (FIG. 1).

2. Keep holding the magnet to the Hot Spot. The LED

will flash green, and then flash red. Then the red

light will stay lit.

3. Remove the magnet.

4. While the red light is illuminated, a series of beeps

occur as the device connects.

5. Successfully connecting is indicated by a

high/low/high series of beeps that indicate the data

is being sent to Pulse Level. The LED turns green

after data is successfully sent.

6. Once activated, the device uploads readings at

scheduled times, if assigned to a tank in Pulse

Level.

• The device measures the tank liquid level.

NOTICE

• Do not over tighten TLM into tank bung. Over

tightening can cause permanent damage and

result in inaccurate readings.

• Do not use the TLM with pressurized tanks. Using

the TLM in a pressurized tank will damage the

TLM.

• Do not use thread sealant or adhesive. Many of

these products are chemically incompatible with

the ABS plastic.

FIG. 1

Hot Spot

LED light

Installation

3A8551E 3

LED Pattern

Beep Pattern

Typical Installation

Mount Options

Identify a threaded opening on the top of the tank for

the device to be installed. The location should be

vertical with a clear path to the contents of the tank.

There should be no obstructions that could interfere

with the signal. Insert the threaded device by screwing

it into the opening. Do not over tighten.

1. If the hole is not threaded, place the foam gasket

(included with kit) over the opening.

2. Place the mounting adapter (included with kit) on

top of the foam gasket.

3. Use the two (2) stainless steel self-tapping,

counter-sunk screws (included with kit) to attach

the adapter to the tank. Do not over tighten.

4. Attach the device to the adapter. To form a secure

seal, make sure that the device is vertical on the

tank, that it is secured correctly to the base, and

that the threads have not crossed.

NOTE: If the tank does not contain a suitably positioned

opening at the top of the tank, reference Drilling,

page 4.

LED Pattern Function

LED Test: when a magnet is held

against the hot spot, the LED is

briefly green, followed by briefly

red, then the LED is off.

Red LED Lit Modem Busy: registering on the

network and sending data.

Green LED Lit

Activated: the server has

responded and activated the

server.

Beep Pattern Definition

Low beep once per

second Network registration

High beep once per

second TCP connecting

Low beep once every

four (4) seconds

Network / TCP listen for

commands

Low beep once every two

(2) seconds Re-establish network / TCP

High /Low combination

beep Incoming data

Low / High combination

beep Outgoing data

Low double beep every

four (4) seconds

Network listen (data

received and the device is

active)

FIG. 2

Installation

4 3A8551E

Installation Examples

Drilling

If the tank does not contain a suitable positioned

opening at the top of the tank, it will be necessary to

manually drill into the top of the tank.

1. Select a flat area on the top of the tank located

towards the center (FIG. 3).

2. Drill a 1.5 in. bsp hole at the selected area using a

45.5 mm tapping drill.

3. Continue with Activation.

FIG. 3

Operation

3A8551E 5

Operation

View Data

The TLM is configurable with Pulse Level

(level.gracopulse.com) to take readings at predefined

times.

After configuring the TLM using the Pulse Level, apply

the magnet to the hot spot until a solid red light

appears, creating a connection between the TLM and

the Pulse Level to load the configuration (FIG. 4).

NOTE: Frequent measurements results in shorter

battery life.

Manual Measurement

1. Hold the magnet (supplied) to the Hot Spot directly

under the LED to activate the device (FIG. 1).

2. Keep holding the magnet to the Hot Spot. The LED

will flash green, and then flash red. Then the red

light will stay lit.

3. Remove the magnet.

FIG. 4

Magnet

Hot Spot FIG. 5

Hot Spot

LED light

Recycling and Disposal

6 3A8551E

Recycling and Disposal

End of Product Life

At the end of the product’s useful life, dismantle and

recycle it in a responsible manner.

• Remove batteries, circuit boards, LCDs (liquid

crystal displays), and other electronic components.

Recycle according to applicable regulations.

• Do not dispose of batteries or electronic

components with household or commercial waste.

• Deliver remaining product to a recycling facility.

Troubleshooting

3A8551E 7

Troubleshooting

Problem Cause Solution

Device is not reporting scheduled

readings.

Out of RF range.

RF obstruction.

Consider implementing a WiFi

network and using Graco’s WiFi

TLM.

Ensure that the TLM is not encased

in metal, since this would obstruct

the signal.

Weak or dead batteries. Replace batteries. See Replace

Batteries, page 8.

Tank Level Monitor was not

associated with a tank in software.

Assign TLM serial number to tank.

Reading is scheduled when pump

is operating.

Ensure readings are scheduled

during times that the pump is not

operating.

LED will not turn on. Magnet removed too soon. Hold magnet to device hot spot for

a longer period of time.

Try using a stronger magnet.

Weak or dead batteries. Replace batteries. See Replace

Batteries, page 8.

Service

8 3A8551E

Service

After the TLM has been installed, the only additional

maintenance or service necessary is changing the

batteries.

Replace Batteries

NOTE: After battery placement, activate the TLM with a

magnet (see Activation, page 2), to synchronize the

TLM internal clock to maintain scheduled TLM

readings.

1. Remove the TLM from the tank by unscrewing it

from the opening.

2. Remove the four (4) screws that keep the case

together (FIG. 6).

3. Verify that the device is right side up before

opening to prevent the batteries from falling out

(FIG. 7).

4. Replace the four (4) C-cell Alkaline batteries

(FIG. 8).

WARNING

Fire and Explosion Hazard

Sparking can occur when changing batteries. Only

replace the batteries in a non-hazardous location

away from flammable fluids and fumes.

FIG. 6

FIG. 7

FIG. 8

Bottom

Top

Negative (-) Positive (+)

Service

3A8551E 9

5. Make sure that the gasket is placed correctly (FIG.

9).

6. Reconnect the two halves, then replace the four (4)

screws.

7. Re-install the TLM back into the tank opening.

8. Take a manual measurement to verify the TLM is

activated.

FIG. 9

Gasket

Dimensions - Tank Specifications

10 3A8551E

Dimensions - Tank Specifications

Vertical Tank:

• Maximum Volume - 999,999 gallons or liters.

• Tank walls must be uniformly vertical from empty

level to full.

Cylindrical Tank:

• Maximum volume = 999,999 gallons or liters.

• Tank end walls must be flat; they cannot be any

other shape, including belled.

Obround Tank:

• Maximum volume = 999,999 gallons or liters.

• Tank end walls must be flat; they cannot be any

other shape, including belled.

Non-Standard Tanks:

• Maximum volume = 999,000 gallons or liters.

• Define strapping table in Pulse Level software.

• Up to 100 strapping table points to correlate tank

fluid height to volume.

FIG. 10

FIG. 11

FIG. 12

Width

Table des matières

Autres manuels Graco Instrument de mesure

Graco

Graco HG6000 Manuel de référence technique

Graco

Graco PE14 Manuel utilisateur

Graco

Graco 309455C Manuel d'utilisation

Graco

Graco 26C266 Manuel utilisateur

Graco

Graco IM20P Fiche technique

Graco

Graco G3000 Manuel utilisateur

Graco

Graco SDMM8 Manuel utilisateur

Graco

Graco 24J318 Manuel utilisateur

Graco

Graco Accu-Shot 233807 Manuel utilisateur

Graco

Graco Pulse TLM Manuel d'utilisation

Graco

Graco Accu-Shot 233807 Manuel de la liste des pièces

Graco

Graco PPM 3050H Manuel d'utilisation

Graco

Graco PSM Manuel utilisateur

Graco

Graco G3000 Manuel d'utilisation

Graco

Graco HORIZON Manuel d'utilisation

Graco

Graco PM8 Manuel utilisateur

Graco

Graco G250 Manuel de la liste des pièces

Graco

Graco 244023 Fiche technique

Graco

Graco 244075 Manuel d'utilisation

Graco

Graco EFC C Series Manuel d'utilisation

Graco

Graco PM8 Guide de configuration

Graco

Graco FLOW METERS S3000 Manuel utilisateur

Graco

Graco EM5 Series Manuel utilisateur

Graco

Graco XDI12 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur