Graco Pulse TLM Manuel d'utilisation
3A8551B
EN
Installation, Operation, and Service
Pulse® Level Cellular
Tank Level Monitor
Measures the distance between the device and the surface of the fluid to determine the volume of fluid within
a tank. For use only with Pulse Level. Intended fluids: oil, diesel, waste oil, automatic transmission fluid
(ATF), kerosene, anti-freeze, windshield washer solution, waste water, and DEF. For professional use only.
Not suitable for tank overfill protection.
Not approved for use in explosive atmospheres or hazardous (classified) locations.
Part No. 25T461
Important Safety Instructions
Read all warnings and instructions in this
manual and in all related Pulse manuals
before using the equipment. Save all
instructions.
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not alter or modify equipment. Alterations or
modifications may void agency approvals and
create safety hazards.
• Make sure all equipment is rated and approved for
the environment in which you are using it.
• Use equipment only for its intended purpose. Call
your distributor for information.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the
work area to help prevent serious injury, including eye
injury, hearing loss, and inhalation of toxic fumes.
This Tank Level Monitor (TLM) contains FCC ID XMR
201707 BG96. This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two
conditions:
• This device may not case harmful interference.
• This device must accept any interference received,
including interference that may cause undesired
operation.
Installation
2 3A8551B
Installation
Set Up
Register TLM to Tank in Pulse
Level Software
Navigate to URL: level.gracopulse.com
This device requires access to a cellular network to
work, and can be activated in Pulse Level. Refer to
Pulse Level terms of service in the About section of the
software.
After creating user, organization, branch and site,
navigate to Devices (located in the upper right corner of
the screen). Associate the device to your organization
by entering the serial number. When you create a tank
for the site, the device will be assignable.
Assign the TLM serial number to a tank in Pulse Level.
Activation
1. Hold the magnet (supplied) to the Hot Spot directly
under the LED to activate the device (FIG. 1).
2. Keep holding the magnet to the Hot Spot. The LED
will flash green, and then flash red. Then the red
light will stay lit.
3. Remove the magnet.
4. While the red light is illuminated, a series of beeps
occur as the device connects.
5. Successfully connecting is indicated by a
high/low/high series of beeps that indicate the data
is being sent to Pulse Level. The LED turns green
after data is successfully sent.
6. Once activated, the device uploads readings at
scheduled times, if assigned to a tank in Pulse
Level.
• The device measures the tank liquid level.
NOTICE
• Do not over tighten TLM into tank bung. Over
tightening can cause permanent damage and
result in inaccurate readings.
• Do not use the TLM with pressurized tanks. Using
the TLM in a pressurized tank will damage the
TLM.
• Do not use thread sealant or adhesive. Many of
these products are chemically incompatible with
the ABS plastic.
FIG. 1
Hot Spot
LED light
Installation
3A8551B 3
LED Pattern
Beep Pattern
Typical Installation
Mount Options
Identify a threaded opening on the top of the tank for the
device to be installed. The location should be vertical
with a clear path to the contents of the tank. There
should be no obstructions that could interfere with the
signal. Insert the threaded device by screwing it into the
opening. Do not over tighten.
1. If the hole is not threaded, place the foam gasket
(included with kit) over the opening.
2. Place the mounting adapter (included with kit) on
top of the foam gasket.
3. Use the two (2) stainless steel self-tapping,
counter-sunk screws (included with kit) to attach the
adapter to the tank. Do not over tighten.
4. Attach the device to the adapter. To form a secure
seal, make sure that the device is vertical on the
tank, that it is secured correctly to the base, and that
the threads have not crossed.
NOTE: If the tank does not contain a suitably positioned
opening at the top of the tank, reference Drilling, page
4.
LED Pattern Function
LED Test: when a magnet is held
against the hot spot, the LED is
briefly green, followed by briefly
red, then the LED is off.
Red LED Lit Modem Busy: registering on the
network and sending data.
Green LED Lit
Activated: the server has
responded and activated the
server.
Beep Pattern Definition
Low beep once per
second Network registration
High beep once per
second TCP connecting
Low beep once every four
(4) seconds
Network / TCP listen for
commands
Low beep once every two
(2) seconds Re-establish network / TCP
High /Low combination
beep Incoming data
Low / High combination
beep Outgoing data
Low double beep every
four (4) seconds
Network listen (data
received and the device is
active)
FIG. 2
Installation
4 3A8551B
Installation Examples
Drilling
If the tank does not contain a suitable positioned
opening at the top of the tank, it will be necessary to
manually drill into the top of the tank.
1. Select a flat area on the top of the tank located
towards the center (FIG. 3).
2. Drill a 1.5 in. bsp hole at the selected area using a
45.5 mm tapping drill.
3. Continue with Activation.
FIG. 3
Operation
3A8551B 5
Operation
View Data
The TLM is configurable with Pulse Level
(level.gracopulse.com) to take readings at predefined
times.
After configuring the TLM using the Pulse Level, apply
the magnet to the hot spot until a solid red light appears,
creating a connection between the TLM and the Pulse
Level to load the configuration (FIG. 4).
NOTE: Frequent measurements results in shorter
battery life.
Manual Measurement
1. Hold the magnet (supplied) to the Hot Spot directly
under the LED to activate the device (FIG. 1).
2. Keep holding the magnet to the Hot Spot. The LED
will flash green, and then flash red. Then the red
light will stay lit.
3. Remove the magnet.
FIG. 4
Magnet
Hot Spot FIG. 5
Hot Spot
LED light
Recycling and Disposal
6 3A8551B
Recycling and Disposal
End of Product Life
At the end of the product’s useful life, dismantle and
recycle it in a responsible manner.
• Remove batteries, circuit boards, LCDs (liquid
crystal displays), and other electronic components.
Recycle according to applicable regulations.
• Do not dispose of batteries or electronic
components with household or commercial waste.
• Deliver remaining product to a recycling facility.
Troubleshooting
3A8551B 7
Troubleshooting
Problem Cause Solution
Device is not reporting scheduled
readings.
Out of RF range.
RF obstruction.
Consider implementing a WiFi
network and using Graco’s WiFi
TLM.
Ensure that the TLM is not encased
in metal, since this would obstruct
the signal.
Weak or dead batteries. Replace batteries. See Replace
Batteries, page 8.
Tank Level Monitor was not
associated with a tank in software.
Assign TLM serial number to tank.
Reading is scheduled when pump
is operating.
Ensure readings are scheduled
during times that the pump is not
operating.
LED will not turn on. Magnet removed too soon. Hold magnet to device hot spot for
a longer period of time.
Try using a stronger magnet.
Weak or dead batteries. Replace batteries. See Replace
Batteries, page 8.
Service
8 3A8551B
Service
After the TLM has been installed, the only additional
maintenance or service necessary is changing the
batteries.
Replace Batteries
NOTE: After battery placement, activate the TLM with a
magnet (see Activation, page 2), to synchronize the
TLM internal clock to maintain scheduled TLM
readings.
1. Remove the TLM from the tank by unscrewing it
from the opening.
2. Remove the four (4) screws that keep the case
together (FIG. 6).
3. Verify that the device is right side up before opening
to prevent the batteries from falling out (FIG. 7).
4. Replace the four (4) C-cell Alkaline batteries
(FIG. 8).
WARNING
Fire and Explosion Hazard
Sparking can occur when changing batteries. Only
replace the batteries in a non-hazardous location
away from flammable fluids and fumes.
FIG. 6
FIG. 7
FIG. 8
Bottom
Top
Negative (-) Positive (+)
Dimensions - Tank Specifications
10 3A8551B
Dimensions - Tank Specifications
Vertical Tank:
• Maximum Volume - 999,999 gallons or liters.
• Tank walls must be uniformly vertical from empty
level to full.
Cylindrical Tank:
• Maximum volume = 999,999 gallons or liters.
• Tank end walls must be flat; they cannot be any
other shape, including belled.
Obround Tank:
• Maximum volume = 999,999 gallons or liters.
• Tank end walls must be flat; they cannot be any
other shape, including belled.
Non-Standard Tanks:
• Maximum volume = 999,000 gallons or liters.
• Define strapping table in Pulse Level software.
• Up to 100 strapping table points to correlate tank
fluid height to volume.
FIG. 10
FIG. 11
FIG. 12
Width
Autres manuels pour Pulse TLM
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Graco Instrument de mesure
Graco
Graco PE14 Manuel utilisateur
Graco
Graco 244023 Fiche technique
Graco
Graco 255348 Manuel utilisateur
Graco
Graco XDI12 Manuel utilisateur
Graco
Graco Accu-Shot 233807 Manuel de la liste des pièces
Graco
Graco ProControl 1KE Plus Manuel d'utilisation
Graco
Graco PD44 Manuel utilisateur
Graco
Graco PGM Manuel de la liste des pièces
Graco
Graco PM8 Manuel utilisateur
Graco
Graco PSM Manuel utilisateur
Graco
Graco G3000 Manuel d'utilisation
Graco
Graco HG6000 Manuel de référence technique
Graco
Graco 244075 Manuel utilisateur
Graco
Graco EM5 Series Manuel utilisateur
Graco
Graco 26C266 Manuel utilisateur
Graco
Graco FX250 Manuel d'utilisation
Graco
Graco 244075 Manuel d'utilisation
Graco
Graco EFC C Series Manuel d'utilisation
Graco
Graco PPM 3050H Manuel d'utilisation
Graco
Graco FLOW METERS S3000 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur