GE 24959 Manuel utilisateur

24959

Universal Remote

Instruction Manual

Table of Contents

Introduction...............................................3

Button Functions.......................................4

Initial Setup...............................................6

Battery Installation................................6

Battery Saver .......................................6

Code Saver ..........................................6

Code Setup ..........................................6

Direct Code Entry .....................................7

Code Search.............................................8

Code Identiﬁcation Feature ......................9

Setup ......................................................10

Programming Combo Device Codes..10

DVD/DVR Punch-Through Feature....10

Volume/Mute Control Feature ............10

Setting All Volume/Mute Controls.......11

Setting Any Mode to Use Own

Volume/Mute ......................................11

Code Learning........................................12

Tips on Learning.................................12

IR Transmitter Finder .............................14

Learning Commands ..............................15

Clearing Commands...............................16

Clearing All Learned Commands .......16

Master Clear.......................................16

Troubleshooting......................................17

Introduction

Congratulations on your purchase of this

GE Universal Remote Control. Your new

remote is one of the most easy to use

remote controls available today. Juggling

multiple remote controls is a thing of the

past! Your GE Remote controls up to

8 devices, including the most popular

brands of TV, DVD, DVR, Cable, etc.

In addition, this remote is equipped with a

command learning feature, which lets the

remote learn commands from your original

equipment remote control!

Note: Some functions from your original

remote may not be controlled by this

remote. Use the original remote, if

available, to control such functions.

Sometimes buttons other than described

in these instructions may actually perform

the function. For example, the CHAN and

VOL buttons might be used to navigate

through menu choices. We recommend

you experiment with the remote to

identify if such situations pertain to your

equipment.

The GE Universal Remote is easy to use,

easy to program, and it gives you total

control—at the touch of your ﬁngertips!

ch/pg

DVR

learn

setup

aspect

amp aux

cbl

dvr

dvd

sat vcr

guide info exit

vol

light

+100 enter

live

replay

list input last

mute

rewind play ff

pause

stop

page

no yes

record

Button Functions

Note: The REC button must be pressed twice to

record from your DVD/DVR. For some DVD/DVR

brands, you might need to press REC button once,

then press it again for 3 seconds.

Some buttons on the remote might have functions

that are referred to by different names on the de-

vice you are controlling. These differences depend

upon the brand and model of your product. Also,

this remote can only operate features that exist on

your product.

10.

11.

12.

13.

14.

28.

27.

26.

25.

24.

23.

22.

21.

20.

19.

18.

17.

16.

15.

Button Functions (cont.)

1. Red Indicator: Lights when any button is pressed.

2. TV, DVD, DVR, etc.: Selects the product to be

operated.

3. ASPECT: Selects viewing format for the displayed

picture (See 14 below).

4. SETUP: Used for setting up your remote.

5. PAGE DOWN: Sets your Favorites ratings.

6. ABCD: Used to store learned commands. (Some

DVRs or Set Top boxes use colors and some use the

letter keys. You may have to try both to ensure correct

functionality.

7. MENU: Brings up the device Menu screen (if

available) - use with UP, DOWN, LEFT, and RIGHT

navigation buttons.

8. GUIDE: Displays satellite or cable on-screen program

guide.

9. VOLUME UP/DOWN: Changes the volume level of

the product, normally the TV.

10. MUTE: Turns off the TV sound while the picture

remains.

11. DVR: Press to display list of recorded shows on

your DVR.

12. REPLAY: On some DVRs, this button replays the last

8 seconds of a program.

13. NUMBERS: Enter numbers for direct channel

selection. Some products require Enter to be pressed

after channel selection.

14. Dot: used for digital channels, e.g., 2.3. (Controls

ASPECT for some DVRs)

+100: Used for channels greater than 100. On some

devices.

15. ENTER: Used after direct channel number entry to

immediately change to the selected channel.

16. RECORD, PLAY, STOP, REW, FF, PAUSE: Control

buttons that operate your DVD/DVR even when the

remote is set to operate the TV. Also operates DVD

Scan -/+.

17. LIVE: Returns to live TV.

18. INPUT: For some TVs, press repeatedly to select from

available viewing sources (antenna, cable box, etc.).

19. LAST: Returns to the previously selected channel or

DVD repeat toggle.

20. OK: Selects menu items for the device you are

controlling.

21. UP, DOWN, LEFT, RIGHT: Navigation buttons.

22. CHANNEL UP/DOWN: Changes the channels. Also

controls DVD/CD CHAPTER +/- track selection, i.e.,

DVD/CD Track Skip Up/Down. Note the DVR buttons

also control the DVD when in DVD Mode.

23. INFO: Displays/selects on-screen channel

information, etc.

24. EXIT: Exits on-screen menus, returns to previous on-

screen selection.

25. PAGE UP: Sets your Favorites ratings.

26. BACKLIGHT: Turns backlighting On/Off.

27. LEARN: Used to setup learning functions.

28. POWER: Turns device on or off.

Initial Setup

Battery Installation

1. On the back of the remote, push down on the

tab and lift the cover off.

2. Match the batteries to the + and - marks inside

the battery case, then insert 2 AAA Alkaline

batteries.

3. Press the battery cover back into place.

Battery Saver

Your remote automatically turns off if the buttons

are depressed more than 30 seconds. This will

save your batteries should your remote get stuck in

a place where the buttons remain depressed (e.g.,

or for instance, between the sofa cushions).

Code Saver

Codes are stored in permanent memory while you

are changing batteries so that you will not lose any

codes stored in the remote while you are changing

batteries.

Code Setup

The SETUP button is used to setup the remote.

You can either setup the remote using the code

for your brand of product, from the code tables (on

separate sheet), or you can search through the

library of codes until you ﬁnd a code that works for

your product.

Please refer to “Code Search” on page 8 for more

information on using the code search feature to

learn how to search through the library of codes for

your products.

Direct Code Entry

NOTE: You can store any kind of code under any

mode (except TV). I.E. you can store a VCR code

under the CBL button, or a DVD code under the

AUX button, etc. However, you can only store TV

codes under the TV button.

1. Press and hold the SETUP button until the red

indicator stays on, then release the SETUP

button.

2. Press and release the desired mode button

(TV,DVD, etc.). The red indicator blinks, then

stays lit.

3. Enter the 4 digit code from the code tables (on

separate sheet). Note: after a valid code entry,

the red indicator turns off. For an invalid code,

the red indicator ﬂashes.

4. With your device on, press CHANNEL UP (or

POWER). If the device responds, no further

programming is required. Note: If some buttons

do not operate your equipment, try one of the

other codes for your brand.

Write your codes down here for easy reference

later.

Type Type stored Code

TV TV

AMP

DVD

SAT

DVR

VCR

CBL

AUX

Code Search

If your product does not respond after you have

tried all the codes for your brand, or if your brand is

not listed, try searching for your code by following

these steps.

1. Manually turn on the device (TV, DVD, etc.) to

be controlled.

2. Press and hold the SETUP button until the red

indicator stays on, then release the SETUP

button.

3. Press and quickly release the desired mode

button (TV, DVD, etc.). The red indicator blinks

off once.

4. Press the CHANNEL UP button repeatedly (up

to 300 times) until the device to be controlled

changes channel. The red indicator blinks off

with each button press. If you accidentally

overshoot the code required, press the

CHANNEL DOWN button to backtrack through

the library until the device changes channel.

Pressing CHANNEL UP changes direction to

forward again.

5. Press and release ENTER to install the code.

Most users store DVD codes under DVD. Cable

codes appear under CBL, etc. If you want to store

a Satellite code under CBL, for example, ﬁrst fol-

low the procedure for Direct Code Entry and select

CBL in Step 2 of Direct Code Entry. Then enter

any Satellite code in Step 3 of Direct Code Entry.

Then follow the steps above for Code Search.

Note: Code Search starts from the currently

stored 4 digit number under that mode. Sometimes

the ﬁrst code that “works” with your device may

only allow limited functionality (e.g. the MENU

button might not work). There may be a code

that performs more functions. Continue the code

search process until the best code is found.

Code Identiﬁcation Feature

The Code Identiﬁcation Feature allows you to

identify the 4 digit library code stored under your

device key. For example, if you want to ﬁnd out

what 4 digit code is stored under your TV device

key, follow the six steps below:

1. Press and hold the SETUP button until the red

indicator stays on. Release the SETUP button.

2. Press and release the desired mode button

(TV, DVD, etc.). The red indicator blinks, then

stays lit.

3. Press and release the SETUP button. The red

indicator blinks off.

4. To ﬁnd the ﬁrst digit for the code stored under

the mode key pressed in step 2, press each

numeric key from 0-9 in turn. When the red

indicator blinks off the number you pressed is

the ﬁrst digit for the code you are searching for.

5. To ﬁnd the second digit, repeat step 4, this

time when the red indicator blinks off this is the

second digit.

6. Repeat step 4 to ﬁnd the third and fourth digits.

Code Identiﬁcation Feature

Programming Combo Device Codes

Some combo (combination) devices (TV/DVR, TV/

DVD, DVD/DVR, etc.) require you to set up 2 dif-

ferent modes to control both parts of the combo.

For example, if you have a TV/DVD combo, you

might need to set up one code under the TV mode

to control the TV and a separate code (under other

modes) to control the DVD.

DVD/DVR Punch-Through Feature

This remote allows the 6 DVD/DVR transport

buttons (i.e. PLAY, PAUSE, STOP, FF, REWIND,

and REC) to operate the programmed TV, DVD,

SAT, DVR, Cable device if the code has these

button functions e.g. if you hvae programmed

a SAT/DVR or Cable/DVR, etc. Otherwise the

transport keys will punch-through to the last DVD

or VCR programmed mode you used, i.e., the

transport buttons control your DVD or VCR player

even when you are in TV, SAT or Cable mode. If

you want to enable this Punch-through feature to

allow the transport keys to always control your last

used DVD or VCR, please use the following steps:

1. Press and hold SETUP until the red indicator

stays on, then release the SETUP button.

2. Press and hold PAUSE until the red indicator

turns off, then release the PAUSE button. The

PAUSE button needs to be held held for about

3 seconds before the red indicator turns off.

The punch-through feature can be disabled again

by repeating the above steps.

Volume/Mute Control and Punch-

Through Feature

Your remote allows you to select which device

mode controls VOLUME and MUTE. This remote

is initially set for all device modes to use their own

Volume/Mute control if present.

If the programmed code does not have Volume/

Mute operation, then VOLUME and MUTE will

“punch-through” (hand-over) control to the TV-

mode device without you needing to change to TV

mode. Note: Any mode chosen for Volume/Mute

control must have its own Volume/Mute function or

else VOLUME and MUTE will not function.

Setup

Table des matières

Autres manuels GE Télécommande universelle

Manuels Télécommande universelle populaires d'autres marques

Pronto

Pronto Peel Manuel utilisateur

Radio Shack

Radio Shack Wireless Remote Control System Manuel utilisateur

AUVIO

AUVIO Universal Home Theater Remote Manuel utilisateur

Philips

Philips Icon SRU4106 Manuel utilisateur

THOMSON

THOMSON ROC4309 Manuel utilisateur

Philips

Philips pm625S Manuel utilisateur

RCA

RCA RCU600WMS - Universal Remote Control Manuel utilisateur

Blackweb

Blackweb BWB17AV002 Manuel utilisateur

Marmitek

Marmitek DoorGuard 300 Manuel utilisateur

Chunghop

Chunghop RM-L618 Manuel utilisateur

Anderic

Anderic KTN828 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Manuel utilisateur

Medion

Medion E74023 Manuel utilisateur

intensity

intensity RM02A Manuel utilisateur

Sky

Sky MY Manuel utilisateur

RCA

RCA RCU600M - Universal Remote Control Manuel utilisateur

Savant

Savant SUR-0500 Guide de référence rapide

GDI

GDI GDI-WT2K Manuel utilisateur