GE 26607 Manuel utilisateur

Universal Remote

Instruction Manual

Control Remoto Universal

Manual de Instrucciones

26607

7252

TV CBL DVR DVD

SAT

AUDIO

AUX2

AUX1

A B C D

MUTE

LAST

VOL

123

456

7 8 9

DVR LIST

MENU SHIFT

SETUPINFO

INPUT

GUIDE

EXIT

Scan this to view remote

setup video

Mira a ver el video de

instalación remota

http://www.jascoproducts.com/remote

Congratulations on your purchase of the GE Universal

Remote Control. The GE Universal Remote Control

is one of the most easy-to-use remote controls

available today. With the GE Universal Remote

Control, juggling multiple remote controls is a thing of

the past! Your GE Universal Remote Control, controls

multiple devices, including the most popular brands

of TVs, DVRs, DVDs, CBL and SAT. The GE Universal

Remote Control is easy to use and easy to program,

and it gives you total control — at the touch of your

ﬁngertips!

IMPORTANT: SAVE THIS MANUAL AND CODE LIST

FOR FUTURE REFERENCE

Introduction..................................................................................... 2

Setup .................................................................................................. 3

Battery Installation............................................................... 3

Battery Saver........................................................................... 3

Code Saver ............................................................................... 3

Button Functions ................................................................... 4

Programming Your Remote..................................................... 6

Direct Code Entry................................................................... 6

Auto Code Search ................................................................. 8

Favorite Function .................................................................. 9

Controlling Combo Devices............................................10

Using Your Remote....................................................................11

Using SHIFT............................................................................11

Master Volume Feature....................................................12

Code Identiﬁcation .............................................................13

Reset to Factory Settings........................................................13

Troubleshooting..........................................................................14

Warranty ........................................................................................15

FCC Statement.............................................................................16

Table of Contents

Your universal remote requires two (2) AAA batteries

(not included). Alkaline batteries are recommended.

Battery Installation

1. On the back of the remote, pull down on

the textured surface and slide battery cover

downward to remove.

2. Match the (+) and (-) marks on the batteries to the

(+) and (-) marks inside the battery compartment,

then insert two (2) AAA batteries. Be sure to use

fresh batteries.

3. Position battery cover slightly below opening and

push upward to lock into place.

NOTE: If your remote stops operating properly,

replace the batteries with new ones. The remote will

retain the codes you have programmed for up to 10

minutes after the batteries are removed.

Battery Precautions

• Donotmixoldandnewbatteries.

• Donotmixalkaline,standard(carbon-zinc),or

rechargeable (Ni-Cd, Ni-MH, etc.) batteries.

• Alwaysremoveold,weakorworn-outbatteries

promptly and recycle or dispose of them in

accordance with local and national regulations.

Battery Saver

Your remote automatically turns off if the buttons are

depressed more than 8 seconds. This will save your

batteries should your remote get stuck in a place

where the buttons remain depressed (e.g., between

the sofa cushions).

Code Saver

You will have up to 10 minutes to change the

batteries in your remote without losing codes you

have programmed. However, do not press any

buttons until batteries are installed in the remote. If

buttons are pressed without batteries in the remote,

all codes will be lost.

Setup

Button Functions

ENTER

For some TV models,

used after direct

channel number entry

to immediately change

to the selected channel.

MUTE Turns off the

TV sound while the

picture remains.

RECORD, PLAY, STOP,

REW, FF, PAUSE

TV, CBL, DVR, DVD, SAT,

AMP, AUX 1, AUX 2

Selects device

to control.

Red Indicator lights when

any button is pressed.

UP, DOWN,

LEFT & RIGHT

Navigation buttons.

ABCD (yellow, blue,

red and green) Allows

access to additional

features for DVRs,

cable box, satellite,

Blu-ray™, etc...

(additional features vary by

device type and brand, see

device owner's manual for

information).

GUIDE Displays satellite

or cable on-screen

program guide.

MENU Displays the

Menu on the TV.

DVR LIST Displays list of

recorded programs

TV CBL DVR DVD

SAT

AUDIO AUX2

AUX1

A B C D

MUTE

LAST

VOL

123

456

7 8 9

DVR LIST

MENU SHIFT

SETUPINFO

INPUT

GUIDE

EXIT

OK Selects menu items for the

device you are controlling.

Button Functions, cont.

DOT: Used to select

digital channels, e.g., 2.3.

VOLUME UP/DOWN

Changes the volume

level of the device,

normally the TV.

NUMBERS

Enter numbers for direct

channel selection. Some

devices require ENTER

to be pressed after

channel selection.

ON•OFF Turns

devices On or Off.

CHANNEL UP/DOWN

Changes the channels.

SETUP Used to

setup the remote,

and for code

search function.

INPUT Selects the video inputs

from available viewing sources.

Info (i) Displays

on-screen channel

information, etc.

EXIT

Exits On-Screen Menus.

LAST Returns to the

previously selected

channel, or DVD

repeat toggle.

SHIFT is the alternate

function of this button.

Use the SHIFT button to

access the menu and

DVR list of your device.

To enter the SHIFT

mode press this button

once. To exit the shift

mode, press the

SHIFT button again.

TV CBL DVR DVD

SAT

AUDIO AUX2

AUX1

A B C D

MUTE

LAST

VOL

123

456

7 8 9

DVR LIST

MENU SHIFT

SETUPINFO

INPUT

GUIDE

EXIT

Programming Your Remote

Your GE universal remote control is designed to

control multiple audio/video devices such as a TV,

DVD, DVR, satellite, cable and audio device using

only one remote. To use this remote, you will need to

program it to control the devices of your choice. There

are two ways to program the remote - direct code

entry or auto code search.

Direct Code Entry (Recommended)

1. Locate the Remote Code List provided

in this manual. Find the DEVICE

CATEGORY you wish to program (for

example TV, CBL, DVR, DVD, SAT,

AMP, AUX 1, AUX 2) and then ﬁnd the

BRAND of that device. Circle all the

codes under that brand. Example: For

a GE TV, locate the TV code section

then circle all of the GE TV codes.

2. Manually turn on the device you wish

to control.

3. Press and hold the SETUP button

until the red indicator light stays on

(approximately 2 seconds) and then

release the SETUP button.

4. Press and release the device button on

the remote (TV, CBL, DVR, DVD, SAT,

AMP, AUX 1, AUX 2). The red indicator

will blink once and then remain on.

5. Enter the ﬁrst 4-digit code previously

found in the code list using the

number buttons on the remote. If the

code entered is a valid code, the red

indicator light will turn off. If the code

entered is not a valid code, the red

indicator light will ﬂash and remain on

allowing you to re-enter the code.

Note: If no buttons are pressed for 35

seconds, the remote will exit the SETUP

mode and you will have to start over.

Programming Your Remote, cont.

6. Point the remote at the device. Press

the POWER button—if the device

turns off, no further programming is

required for that device. If the device

does not turn off, return to step 3 and

use the next code found in the code

list. Continue this process until a code

for your device is found.

7. Repeat this process for each device

(for example TV, CBL, DVR, DVD, SAT,

AMP, AUX 1, AUX 2) in your home

entertainment system you wish

to control.

Programming Notes

• Ifyourdevicedoesnotrespondtotheremoteafter

trying all codes listed or your brand is not listed in

the code list, use the Auto Code Search method to

program your remote.

• Sometimestherstcodethat“works”withyour

device may operate only a few functions of your

device. There may be another code in the code

list that performs more functions. Try other codes

from the code list for more functionality.

• WiththeDirectCodeEntrymethod,youcan

program any device button to control any device

in your home entertainment system.

For example, you can use the DVR or AUX device

button to control an audio receiver or a DVD, VCR,

satellite device, etc.

• Forcombinationdevices,youmayhavetoentera

code for each device. For example, for a VCR/DVD

device, you may have to enter a code for the DVD

under the DVD button and enter a code for the

VCR using a different device button on the remote.

• Writedownthecodefoundtooperateyourdevice

for future reference.

Programming Your Remote, cont.

Auto Code Search

The Auto Code Search searches automatically through

the codes stored in this remote. Read all the following

steps prior to starting the auto code search as you will

need to be prepared to lock-in the proper code when

found.

1. Manually turn on the device you wish

to control.

2. Press and hold the SETUP button

until the red indicator light stays on

(approximately 2 seconds) and then

release the button.

3. Press and release the desired device

button on the remote (TV, CBL, DVR,

DVD, SAT, AMP, AUX 1, AUX 2) the

type of device you wish to control. The

red indicator will blink once and then

remain on.

4. Point the remote at the device and

press and release the POWER

button (for TV) or PLAY button (for

DVD, VCR, etc.) to start the search. The

red indicator will ﬂash

(approximately every 2 seconds) as

the remote searches. Note: The remote

must be pointed at the device for the

duration of this search.

5. Place your ﬁnger on the #1 button so

you are prepared to lock-in the code.

6. When the device shuts off or begins

playing, press the #1 button to lock-in

the code. The red indicator light will

turn off. Note: You have approximately

two seconds after the device shuts off

or begins playing to lock-in the code.

7. Point the remote at the device and

check to see if the remote operates

the device as desired. If it does, no

further programming is required for

that device. If it does not, return to step

2 and start the auto code search again.

Programming Your Remote, cont.

8. Repeat this process for each device (for example

TV, DVD, SAT, AUX) in your home entertainment

system you wish to control.

Programming Notes

• Thisprocessmaytakeseveralminutesasthe

remote contains many codes.

• WhenusingtheAutoCodeSearchprogramming

method, the device button corresponding to

the type of device you want to control must be

selected (for example, the TV device button must

be selected in step 3 if you want to control a TV,

the DVD device button for a DVD player, etc.)

• TheSETUP button can be used during the search

process to reverse the direction of the search of

the remote codes. For example, if you miss the

code for your device and the remote is continuing

to search (as indicated by the blinking red light),

press the SETUP button and the code search will

reverse direction and return to the code.

• Sometimestherstcodethat“works”withyour

device may operate only a few functions of your

device. There may be another code in the code

list that performs more functions. Continue the

auto code search as directed above until the best

code is found.

Programming Your Remote, cont.

Controlling Combo Devices

Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/

VCR, etc.) will require you to set up two different Mode

buttons to control both parts of the Combo device.

For example, if you have a TV/DVD Combo, you might

need to set up one code under the TV button to

control the TV part AND a separate code (under any

other Mode button) to control the DVD part.

Table des matières

Langues :

Autres manuels GE Télécommande universelle

Manuels Télécommande universelle populaires d'autres marques

Pronto

Pronto Peel Manuel utilisateur

Radio Shack

Radio Shack Wireless Remote Control System Manuel utilisateur

AUVIO

AUVIO Universal Home Theater Remote Manuel utilisateur

Philips

Philips Icon SRU4106 Manuel utilisateur

THOMSON

THOMSON ROC4309 Manuel utilisateur

Philips

Philips pm625S Manuel utilisateur

RCA

RCA RCU600WMS - Universal Remote Control Manuel utilisateur

Blackweb

Blackweb BWB17AV002 Manuel utilisateur

Marmitek

Marmitek DoorGuard 300 Manuel utilisateur

Chunghop

Chunghop RM-L618 Manuel utilisateur

Anderic

Anderic KTN828 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Manuel utilisateur

Medion

Medion E74023 Manuel utilisateur

intensity

intensity RM02A Manuel utilisateur

Sky

Sky MY Manuel utilisateur

RCA

RCA RCU600M - Universal Remote Control Manuel utilisateur

Savant

Savant SUR-0500 Guide de référence rapide

GDI

GDI GDI-WT2K Manuel utilisateur