GE RM24906 Manuel utilisateur

Universal Remote

Instruction Manual

RM24906

Congratulations on your purchase of the RM24906

Universal Remote Control. The RM24906 is one

of the most easy to use remote controls available

today. With the RM24906, juggling multiple remote

controls is a thing of the past! Your RM24906

controls up to four devices, including the most

popular brands of TV, VCR, DVD, CBL, and SAT.

The RM24906 is easy to use, easy to program,

and it gives you total control—at the touch of your

ﬁngertips!

Note: Some functions from your original remote

may not be controlled by this remote. Use the

original remote, if available, to control such

functions. Sometimes buttons other than described

in these instructions may actually perform the

function. For example, the CHAN and VOL

buttons might be used to navigate through menu

choices. We recommend you experiment with the

remote to identify if such situations pertain to your

equipment.

Introduction............................................................ 3

Setup ..................................................................... 3

Battery Installation............................................ 3

Battery Saver.................................................... 3

Code Saver ...................................................... 3

Code Setup ...................................................... 3

Button Functions .............................................. 4

Menu Operation................................................ 6

Direct Code Entry ............................................. 7

Code Search .................................................... 8

Using Your Remote................................................ 9

Code Identiﬁcation............................................ 9

Sleep Function ............................................... 10

Controlling Devices with Power On and Off ... 11

Controlling Combo Devices............................ 11

VCR/DVD/DVR Punch-Through..................... 11

Volume/Mute Control and Punch-Through ..... 12

All Volume/Mute Control to any one Mode ..... 12

Setting any Mode for its own Volume/Mute .... 13

Troubleshooting................................................... 14

Table of Contents

Battery Installation

1. On the back of the remote, push down on the

tab and lift the cover off.

2. Match the batteries to the + and - marks inside

the battery case, then insert 2 AAA Alkaline

batteries.

3. Press the battery cover back into place.

Battery Saver

Your remote automatically turns off if the buttons

are depressed more than 30 seconds. This will

save your batteries should your remote get stuck in

a place where the buttons remain depressed (e.g.,

between the sofa cushions).

Code Saver

You will have up to 10 minutes to change the

batteries in your remote without losing codes you

have programmed. However, do not press any

buttons until batteries are installed in the remote.

If buttons are pressed without batteries in the

remote, all codes will be lost.

Code Setup

The CODE SEARCH button is used to setup the

remote. You can either setup the remote using the

code tables (on separate sheet), or you can search

through the library of codes until you ﬁnd a code

that works for your product. Please refer to “ Code

Search” on page 8 for more information on using

the code search feature to learn how to search

through the library of codes for your products.

NOTE: You can store any kind of code under any

mode (except TV). I.E. you can store a VCR code

under the CBL/SAT button, or a Cable code under

the DVD/AUX button, etc. However, you can only

store TV codes under the TV button.

Setup

VOLUME UP/DOWN

Changes the volume

level of the product,

normally the TV.

CHANNEL Up/Down

Changes the channels.

The Channel buttons

also control DVD SKIP

functions.

MUTE Turns off the

TV sound while the

picture remains.

RECORD, PLAY,

STOP, REW, FF,

PAUSE VCR control

buttons operate your

VCR even when the

remote is set to operate

the TV. Also operates

DVD Scan -/+. Note

the VCR buttons also

control DVD when in

DVD Mode.

Some buttons on the remote might have functions that

are referred to by different names on the device you

are controlling. E.G. PREV.CH may be called RECALL,

or ENTER may be called DISPLAY. These differences

depend on the brand and model of your product. Also,

this remote can only operate features that exist on your

product. E.G., your product must have PREV.CH ability

for the PREV.CH button to operate this feature.

TV, VCR, DVD/AUX,

CBL/SAT Selects product

to be operated.

Button Functions

MENU Brings up device

Main Menu. Use Chan

and Vol buttons as cursor

buttons and Mute as Okay.

Press TV to Exit.

TV/VCR Operates the

same as the TV/VCR

or antenna keys on

your original remotes.

0-9

Enters numbers

for direct channel

selection. Some

products require

ENTER to be

pressed after

channel selection.

ON•OFF Turns

product On or Off.

Button Functions, cont.

CODE SEARCH Used

to setup the remote, and

for code search function.

Note: The REC button must be pressed TWICE to record

from your VCR. For some brands of VCRs, you might

need to press the REC button once, then press it again

for three seconds.

ENTER

Used to complete

channels selection for

some brands of TV.

Also used to com-

plete the code entry

process.

SLEEP enables the

remote to turn off your

TV after a period of 1 to

99 minutes.

PREV.CH Returns to

the previously selected

channel.

Menu Operation

The Menu button puts the remote in and out of

Menu Mode. Pressing Menu brings up your

device Menu. While in Menu mode the remote’s

red indicator light blinks continuously. The remote

will exit Menu Mode after 20 seconds if no keys are

pressed.

When in Menu Mode, the Menu, Channel, Volume,

Mute and Device keys operate as follows:

MENU Enters Menu mode.

CHANNEL UP/DOWN Cursor Up/Down for Menu

navigation.

VOLUME UP/DOWN Cursor Right/Left for Menu

navigation.

MUTE (OK) command for Menu selections.

Press TV or any other Device key to Exit, Clear,

or Quit the Device Menu and return the remote to

normal operation (red indicator will turn off).

For certain RCA, GE, and ProScan devices,

pushing the MENU button selects the highlighted

item. The numeric buttons may also be used to

select the MENU choice.

Note: Some functions in some brands might not be

fully supported.

Write your codes down here for easy reference

later.

Direct Code Entry

1. Press and hold the CODE SEARCH

button until the red indicator stays on,

then release the CODE SEARCH button.

2. Press and release the desired device

button (TV,VCR, etc.). The red indicator

blinks, then stays lit.

3. Enter the 4 digit code

from the code tables

(on separate sheet).

Note: after a valid

code entry, the red

indicator turns off. For

an invalid code, the

red indicator ﬂashes.

4. With your device on, press ON•OFF.

If the device turns off, no further

programming is required. Note: If

some buttons do not operate your

equipment, try one of the other

codes for your brand.

Device Device stored Code

TV TV

VCR

CBL/SAT

DVD/AUX

Code Search

If your device does not respond after you have

tried all the codes for your brand, or if your brand is

not listed, try searching for your code by following

these steps.

1. Manually turn on the device (TV, VCR, etc.) to

be controlled.

2. Press and hold the CODE SEARCH

button until the red indicator stays

on, then release the CODE SEARCH

button.

3. Press and quickly release the desired

device button (TV, VCR, etc.). The red

indicator blinks off once.

4. Press the ON•OFF button repeatedly

(up to 300 times) until the device

to be controlled turns off. The red

indicator blinks off with each button

code.

Most users will store VCR codes under the VCR

button, Cable codes under CABLE, etc. If (for

example) you want to store a VCR code under

DVD/AUX, ﬁrst follow the procedure for Direct

Code Entry (previous page) and press DVD/AUX

in step 2 of Direct Code Entry, then enter ANY VCR

code in step 3 of Direct Code Entry. Then follow

the steps above for Code Search.

Note: Code Search starts from the currently

stored 4 digit number under that mode. Sometimes

the ﬁrst code that “works” with your device may

only allow limited functionality (e.g. the MENU

button might not work). There may be a code

that performs more functions. Continue the code

search process until the best code is found.

press.

5. Press and release ENTER to install the

Using Your Remote

Code Identiﬁcation

The Code Identiﬁcation Feature allows you to

identify the 4 digit library code stored under your

device button. For example, if you want to ﬁnd out

what 4 digit code is stored under your TV device

button, follow the six steps below:

1. Press and hold the CODE SEARCH

button until the red indicator stays on.

Release the CODE SEARCH button.

2. Press and release the desired

device button (TV, VCR, etc.). The

red indicator blinks, then stays lit.

3. Press and release the CODE SEARCH

button. The red indicator blinks once

and remains lit.

4. To ﬁnd the ﬁrst digit

for the code stored

under the device

button pressed in step

2, press each numeric

button from 0-9 in

turn. The number that

causes the indicator

light to blink is the ﬁrst

digit in your code.

5. To ﬁnd the second digit, repeat step 4, this

time when the red indicator blinks off this is the

second digit.

6. Repeat step 4 to ﬁnd the third and fourth digits.

Using Your Remote, cont.

Sleep Function

The Sleep button enables the remote to turn off

your TV after a period of 1 to 99 minutes as shown

below. The remote must be in TV mode to set a

Sleep Timer. This feature works even if your TV

does not have a sleep feature.

1. Press and release the TV device but-

ton.

2. Press and hold the Sleep button until the

onds).

3. Release the Sleep

button.

4. Press and release

the numeric buttons

(01-99) for the time

required. The LED will

blink off to indicate button press acceptance.

5. TV Sleep Timer is set.

6. Leave the Remote pointing towards the TV

with an unobstructed path.

To cancel the Sleep Timer, press and hold the

Sleep button until the LED blinks, or press and

release the Power button in TV mode.

LED remains lit (about 2-3 sec-

Autres manuels pour RM24906

Table des matières

Autres manuels GE Télécommande universelle

Manuels Télécommande universelle populaires d'autres marques

Pronto

Pronto Peel Manuel utilisateur

Radio Shack

Radio Shack Wireless Remote Control System Manuel utilisateur

AUVIO

AUVIO Universal Home Theater Remote Manuel utilisateur

Philips

Philips Icon SRU4106 Manuel utilisateur

THOMSON

THOMSON ROC4309 Manuel utilisateur

Philips

Philips pm625S Manuel utilisateur

RCA

RCA RCU600WMS - Universal Remote Control Manuel utilisateur

Blackweb

Blackweb BWB17AV002 Manuel utilisateur

Marmitek

Marmitek DoorGuard 300 Manuel utilisateur

Chunghop

Chunghop RM-L618 Manuel utilisateur

Anderic

Anderic KTN828 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Manuel utilisateur

Medion

Medion E74023 Manuel utilisateur

intensity

intensity RM02A Manuel utilisateur

Sky

Sky MY Manuel utilisateur

RCA

RCA RCU600M - Universal Remote Control Manuel utilisateur

Savant

Savant SUR-0500 Guide de référence rapide

GDI

GDI GDI-WT2K Manuel utilisateur