GE 24929 Manuel utilisateur

Universal Remote

Instruction Manual

24929

Table of Contents

Introduction..................................................... 3

Button Functions............................................. 4

Setup ............................................................... 6

Battery Installation ..................................... 6

Battery Saver.............................................. 7

Code Saver ................................................. 7

Power-On default ....................................... 7

Code Setup ................................................. 7

Code Entry ...................................................... 8

Direct Code Entry ...................................... 8

Code Search ............................................... 8

Code Identication Feature............................. 9

Programming Combo Device Codes ............ 10

Controlling Combo Devices ......................... 10

Controlling Devices with Power On and Off 10

VCR/DVD/DVR Punch-Through Feature.... 11

Volume/Mute Control Feature ...................... 11

Setting Volume/Mute Control, Punch-Through

Setting any Mode to use its own Volume/Mute

Troubleshooting ............................................ 13

Introduction

Congratulations on your purchase of this

24929 Universal Remote Control. It is one

of the most unique looking, and easy to use

remote controls available today. With the

24929 juggling multiple remote controls is

a thing of the past! Your 24929 Universal

Remote controls up to 4 devices, including the

most popular brands of TV, VCR, DVD, SAT,

CBL, and audio equipment.

Note: Some functions from your original

remote may not be controlled by the 24929

remote. Use the original remote, if available,

to control such functions. Sometimes buttons

other than described in these instructions may

actually perform the function. For example,

the CHAN and VOL buttons might be used

to navigate through menu choices. We

recommend you experiment with the remote

to identify if such situations pertain to your

equipment.

The 24929 Universal Remote is easy to

use, easy to program, and it gives you total

control—at the touch of your ngertips!

Button Functions

10.

20.

19.

18.

17.

16.

15.

14.

13.

12.

11.

Note: The Record button must be pressed TWICE to record

from your VCR. For some brands of VCRs, you might need

to press the Record button once, then press it again for three

seconds. Some buttons on the remote might have functions

that are referred to by different names on the device you are

controlling. E.G. LAST may be called RECALL, or ENTER

may be called DISPLAY. These differences depend on the

brand and model of your product. Also, this remote can only

operate features that exist on your product. E.G., your product

must have LAST ability for the LAST button to operate this

feature.

1. ON-OFF: Turns device On or Off.

2. Red Indicator: Lights when any button is pressed.

3. TV, DVD, CBL/SAT, DVR/AUX: Selects product

to be operated.

4. MUTE: Turns off the TV sound while the picture

remains.

5. VOLUME UP/DOWN: Changes the volume level

of the product, normally the TV.

6. UP, DOWN, LEFT & RIGHT: Navigation but-

tons.

7. MENU: brings up the DVD disc Menu screen. Use

with the UP, DOWN, LEFT & RIGHT navigation

buttons.

5. INPUT Selects the video inputs of your TV if

equipped with that feature.

8. ENTER: Used after direct channel number entry to

immediately change to the selected channel.

9. NUMBERS: Enter numbers for direct channel

selection. Some products require Enter to be pressed

after channel selection.

10. ( ) Used for digital channels, e.g. 2.3.

11. RECORD, PLAY, STOP, REW, FF, PAUSE:

VCR control buttons operate your VCR even when

the remote is set to operate the TV. Also operates

DVD Scan -/+.

12. TV/VCR/INPUT: Operates the same as the TV/

VCR or antenna keys on your original remotes.

13. INFO: Displays on-screen channel information, etc.

14. GUIDE: Displays satellite or cable on-screen pro-

gram guide.

15. EXIT: Exits On-Screen Menus and/or Returns to

previous On-Screen selection.

16. LAST: Returns to the previously selected channel,

or DVD repeat toggle.

17. OK: Selects menu items for the device you are

controlling.

18. CHANNEL UP/DOWN: Changes the channels.

Also controls DVD/CD CHAPTER +/- track

selection i.e. DVD/CD Track Skip Up/Down. Note

the VCR buttons also control DVD when in DVD

Mode.

19. SETUP: Used for setting up your remote.

20. BACKLIGHT: Backlighting On/Off.

Button Functions, cont.

•

Battery Installation

1. On the back of the remote, push down on the tab and

lift the cover off.

2. Match the batteries to the + and - marks inside the

battery case, then insert 2 AAA alkaline batteries.

3. Press the battery cover back into place.

Battery Saver

Your remote automatically turns off if the buttons are

depressed more than 30 seconds. This will save your

batteries should your remote get stuck in a place where

the buttons remain depressed (e.g., between the sofa

cushions).

Code Saver

You will have up to 10 minutes to change the batteries

in your remote without losing codes you have

programmed. However, do not press any buttons until

batteries are installed in the remote. If buttons are

pressed without batteries in the remote, all codes will be

lost.

Power-On Default

The remote powers on in TV mode.

Code Setup

The SETUP button is used to setup the remote. You can

either setup the remote using the code for your brand of

product, from the code tables (on separate sheet), or you

can search through the library of codes until you nd a

code that works for your product.

Please refer to “Programming with Code Search” on

page 8 for more information on using the code search

feature to learn how to search through the library of

codes for your products.

NOTE: You can store any kind of code under any mode

(except TV). I.E. you can store a VCR code under the

CBL button, or a SAT code under the DVD button, etc.

However, you can only store TV codes under the TV

button.

Setup

Direct Code Entry

1. Press and hold the SETUP button until the red

indicator stays on, then release the SETUP button.

2. Press and release the desired mode button (TV,

DVD, etc.). The red indicator blinks, then stays lit.

3. Enter the 4 digit code from the code tables (on

separate sheet). Note: after a valid code entry, the

red indicator turns off. For an invalid code, the red

indicator ashes.

4. With your device on, press CHANNEL UP. If

the device responds, no further programming is

required. Note: If some buttons do not operate your

equipment, try one of the other codes for your brand.

Write your codes down here for easy reference later.

Device Device stored Code

TV TV

DVD

CBL/SAT

DVR/AUX

Code Search

If your product does not respond after you have tried all

the codes for your brand, or if your brand is not listed,

try searching for your code by following these steps.

1. Manually turn on the device (TV, DVD, etc.) to be

controlled.

2. Press and hold the SETUP button until the red

indicator stays on, then release the SETUP button.

3. Press and quickly release the desired mode button

(TV, DVD, etc.). The red indicator blinks off once.

4. Press the CHANNEL UP button repeatedly (up to

300 times) until the device to be controlled changes

channel. The red indicator blinks off with each

button press. If you accidentally overshoot the code

required, press the CHANNEL DOWN button

to backtrack through the library until the device

changes channel. Pressing CHANNEL UP changes

direction to forward again.

5. Press and release ENTER to install the code.

Most users will store DVD codes under the DVD but-

ton, Cable codes under CABLE, etc. If (for example)

you want to store a DVD code under CABLE, rst

follow the procedure for Direct Code Entry (previous

page) and press CABLE in step 2 of Direct Code Entry,

then enter ANY DVD code in step 3 of Direct Code

Entry. Then follow the steps for Code Search on the pre-

vious page. Note: If the device does not have a CHAN-

NEL UP button, use PLAY (DVD only) or ON-OFF

instead. Code Search starts from the currently stored 4

digit number under that mode.

 CodeIdenticationFeature

The Code Identication Feature allows you to identify

the three digit library code stored under your device key.

For example, if you want to nd out what 4 digit code

is stored under your TV device key, follow the six steps

below:

1. Press and hold the SETUP button until the red

indicator stays on. Release the SETUP button.

2. Press and release the desired mode button (TV,

DVD, etc.). The red indicator blinks, then stays lit.

3. Press and release the SETUP button. The red

indicator blinks off.

4. To nd the rst digit for the code stored under the

mode key pressed in step 2, press each numeric key

from 0-9 in turn. When the red indicator blinks off

the number you pressed is the rst digit for the code

you are searching for.

5. To nd the second digit, repeat step 4, this time

when the red indicator blinks off this is the second

digit.

6. Repeat step 4 to nd the third and fourth digits.

Programming Combo Device Codes

Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/

VCR, etc.) will require you to set up two different Mode

buttons to control both parts of the Combo device. For

example, if you have a TV/DVD Combo, you might

need to set up one code under the TV button to control

the TV part AND a separate code (under any other

Mode button) to control the DVD part.

Controlling Combo Devices

Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/

VCR, etc.) have separate buttons on the original remote

to select the part of the Combo device to be controlled.

For example, if your Combo device is a DVD/VCR

then its original remote might have separate DVD and

VCR buttons for selection of the Combo part you would

control. The equivalent button functions can be found

on your new remote by using the device Mode and

SETUP buttons.

Referring to “Programming with Code Search” on

page 8, setup a device Mode (e.g. DVD) with the

correct code for your Combo device. Assuming the

DVD/VCR Combo device is the example and its code

is programmed under DVD Mode, press and hold the

DVD Mode button for more than one second to send

the DVD button command. To send the VCR button

command, quickly press and release the SETUP button

followed by pressing and releasing the DVD Mode

button. This method can be applied similarly to all

Combo devices (e.g. TV/VCR, TV/DVD, DVD/VCR,

etc.) and is available for all Modes. Note this feature is

not supported by all codes.

Controlling Devices Requiring Separate Power On

and Off Buttons

Some devices (e.g. certain RCA TVs) require separate

Power On and Power Off buttons to turn the device on

and off. The equivalent button functions can be found

on your new remote by using the device Mode and ON-

OFF buttons. Referring to “Programming with Code

Search” on page 8, setup a device Mode (e.g. TV) with

the correct code for your device.

Assuming a TV device is the example and its code is

programmed under TV Mode, to turn your TV on, press

and hold the TV Mode button for more than one second

to transmit the Power On button command.

Controlling Devices Requiring Separate Power On

Setup, cont.

Autres manuels pour 24929

Table des matières

Manuels Télécommande universelle populaires d'autres marques

Pronto

Pronto Peel Manuel utilisateur

Radio Shack

Radio Shack Wireless Remote Control System Manuel utilisateur

AUVIO

AUVIO Universal Home Theater Remote Manuel utilisateur

Philips

Philips Icon SRU4106 Manuel utilisateur

THOMSON

THOMSON ROC4309 Manuel utilisateur

Philips

Philips pm625S Manuel utilisateur

RCA

RCA RCU600WMS - Universal Remote Control Manuel utilisateur

Blackweb

Blackweb BWB17AV002 Manuel utilisateur

Marmitek

Marmitek DoorGuard 300 Manuel utilisateur

Chunghop

Chunghop RM-L618 Manuel utilisateur

Anderic

Anderic KTN828 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Manuel utilisateur

Medion

Medion E74023 Manuel utilisateur

intensity

intensity RM02A Manuel utilisateur

Sky

Sky MY Manuel utilisateur

RCA

RCA RCU600M - Universal Remote Control Manuel utilisateur

Savant

Savant SUR-0500 Guide de référence rapide

GDI

GDI GDI-WT2K Manuel utilisateur