Front Runner TRCA008 Manuel utilisateur

ENG

Universal Track

IMPORTANT WARNING!

Don’t be a hero and muscle through this without ﬁrst reading these ﬁtting instructions! Improper installation of this gear may void certain aspects of

your warranty.

Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.

A complete kit will contain:

1. A Front Runner Universal Mounting System

2. A Front Runner Rack Tray or Load Bar Slats

This document will guide you through the assembly of the mounting system and assist you in ﬁtting the roof rack tray or load bars to your speciﬁc

vehicle.

Please refer to the next page for a list of all the components, quantities and tools required.

TRCA008

READ ME FIRST

START HERE!

FRONT RUNNER CAN NOT RECOMMEND A MAXIMUM LOAD CARRYING CAPACITY. PLEASE REFER TO YOUR VEHICLE MANUFACTURER'S RECOMMENDATIONS. IT IS CRITICAL

THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN

AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS

TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE YOU

MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU

DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE

INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

IN THE BOX

FIGURE 1.1

1 4 X M6 x 30 Button Head Bolt

2 4 X M6 x 20 Button Head Bolt

3 4 X M6x12x1 Stainless Steel Flat Washer

4 4 X Track End Cap

5 2 X Track

6 2 X Protective Trim

7 4 X M6x30x1 Flat Washer

8 4 X M6 Nyloc Hex Nut

9 4 X M6 Nut Cap

10 4 X M8 x 12 Button Head Bolt

IN THE BOX TOOLS NEEDED

10 mm 4mm

5mm

Measuring

Tape

IN THE BOX

1GET ORGANIZED

Here is what you are looking at for TRCA008

Sealant Marker

6.5mm

4mm

Utility

Knife

TRCA008_REV_A02

2.1

Remove the Canopy / Cap roof rails if ﬁtted. Determine the best possible position for mounting the

tracks. Take care not to drill into or through any reinforcements.

FIT AND SECURE

2.6

Fit and secure the tracks with a

combination of items 1/2, 6, 7, 8.

Depending on the thickness of the

material you are bolting trough you can

use either item 1 (M6x20 Button Head)

or item 2 (M6x30 Button Head). The bolt

needs to go through the

Nyloc Nut (item 8).

Install the end-caps (Item 4) before you

do the ﬁnal ﬁtment of the tracks.

The track and protective trim (item 3 &

5) must be used on the roof and the

M6x30x1 Flat Washer (item 6) must be

used inside.

Check that all the fasteners are fully

tightened.

Place M6 nut caps (item 9) on all the M6

Nyloc Nuts (item 8) to ﬁnish of the

ﬁtment .

10mm

2.3

Once you are happy with the placement of the track, mark all the holes using a suitable marking pen.

2.4

Drill a 4mm pilot hole on all the marks you have made. Open the pilot holes to 6.5mm.

2.2

Measure and trim the tracks to the desired length.

2.5

Apply a bead of suitable sealant to each hole drilled in step 2.4.

4mm

INSTALL OTHER VEHICLE AND RACK ACCESSORIES

Now's the time to visit your favorite Front Runner Dealer in person or Online.

Roof

Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.

Please call us if you have any questions about the installation of this product.

COMPLETION

Congratulations. You did it. Take a step back and admire your work!

Autres manuels Front Runner Accessoires automobiles

Front Runner

Front Runner SLIMLINE II Manuel utilisateur

Front Runner

Front Runner FAJK002 Mode d’emploi

Front Runner

Front Runner Toyota LAND Cruiser 100 SLIMLINE II Manuel utilisateur

Front Runner

Front Runner SLIMLINE II KRFE009T Manuel

Front Runner

Front Runner SLIMLINE II Instructions de montage

Front Runner

Front Runner SSDS110 Manuel utilisateur

Front Runner

Front Runner SSDR010 Manuel utilisateur

Front Runner

Front Runner FAJK003 Manuel utilisateur

Front Runner

Front Runner RRAC120 Manuel utilisateur

Front Runner

Front Runner TBRA020 Manuel utilisateur

Front Runner

Front Runner FAJK009 Manuel utilisateur

Front Runner

Front Runner SlimSport KSFR002 Manuel utilisateur

Front Runner

Front Runner LATF001 Manuel utilisateur

Front Runner

Front Runner VACC120 Manuel utilisateur

Front Runner

Front Runner SSDR005 Manuel utilisateur

Front Runner

Front Runner LALD005 Manuel utilisateur

Front Runner

Front Runner 200 Series Manuel utilisateur

Front Runner

Front Runner GWTL101-2 Manuel utilisateur

Front Runner

Front Runner MKIII Small Manuel utilisateur

Front Runner

Front Runner SAFE010 Manuel utilisateur

Front Runner

Front Runner SSAM009 Manuel utilisateur

Front Runner

Front Runner QE Series Manuel utilisateur

Front Runner

Front Runner RRAC202 Manuel utilisateur

Front Runner

Front Runner RRAC178 Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur