Front Runner Easy-Out Manuel utilisateur
RRAC029_REV_C01 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
Easy-Out Awning
Brackets
RRAC029
ENG
1
30 min
IMPORTANT WARNING!
Thank you for purchasing the Easy-Out Awning Bracket.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
RRAC029_REV_C01
2
© COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
7
1
6
7
5
2
4
3
6
1
7
8
9
3
4
5
6
2
1
8
9
10
11
TOOLS NEEDED
1 3 X Mounting Bracket
2 15 X M6 x 16 Hex Bolt
3 15 X M6 x 12 x 1SS Flat Washer
4 15 X M6 Nyloc Nut
5 6 X M6 Nut Cap
6 6 X M8 x 20 Hex Bolt
7 15 X M8 x 16 x 1.6SS Flat Washer
8 15 X M8 Nyloc Nut
9 6 X M8 Nut Cap
10 6 X M8 x 25 Button Head Bolt
11 3 X M8 x 20 Button Head Bolt
IN THE BOX
FIGURE 1.1
5mm
6.5mm
13mm
10mm10mm
13mm
GET ORGANIZED1
SLIMLINE II RACK (Steps 2.1 - 2.3)
FIGURE 1.2
SLIMLINE RACK (Steps 3.1 - 3.3)
RRAC029_REV_C01
3
3
4
10
7
711
1
2
AWNING BRACKET INSTALLATION - SLIMLINE II RACK
2
Depending on the type of Awning Extrusion,
slide either three M6 x 16 Hex Bolt or three
M8 x 20 Hex Bolts (Items 2 or 6) into the top
extrusion slot and three into the bottom
extrusion slot.
Place the Mounting Brackets over the
Hex Bolts (two per bracket). Fit a flat washer
and Nyloc Nut onto the bolts used
(Items 3, 4 or 7, 8). Space the Mounting
Brackets accordingly.
13MM
5MM
Position the Awning onto the Slimline II Rack
with the help of a friend. Secure the center
Mounting Bracket first.
Fit the M8 x 16 x 1.6SS Flat washer and the
M8 Nyloc Nuts loosely onto the M8 x 25
Button Head Bolts (Items 7, 8, 10). Do the
same with both other Brackets. Make sure
the Awning is centered correctly.
Underneath the Mounting Brackets, you will
notice the center hole in the Bracket lines up
to the hole in the Side Profile. Insert a
M8 x 20 Button Head Bolt and
M8 x 16 x 1.6SS Flat Washer (Items 7, 11)
and secure with a M8 Nyloc Nut (Item 8).
Fully tighten all fasteners and place Nut Caps
over nuts (Either Item 5 or 9).
2.1
2.2
2.3
Choose which side for the Slimline II Tray
you'd like to install the Awning.
On the chosen side, slide six M8 Nyloc Nuts
(Item 8) in the T-slot channel at the corner of
the Tray making sure the M8 Nyloc Nut
thread is facing upward. Two M8 Nyloc Nuts
will be used for each Mounting Bracket
(Item 1). Spacing of the Nyloc Nuts will
depend on the length of the Tray and the
Awning. The Mounting Brackets
must be positioned between two Slats.
10MM
13MM
RRAC029_REV_C01 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
4
2
AWNING BRACKET INSTALLATION - SLIMLINE RACK
3
10MM
10MM
Drill a 6.5mm hole on the marked positions.
Place the three Mounting Brackets on the
Rack so the holes in the bracket line up
with the holes you drilled. Insert three
M6 x 16 Hex Bolts (Item 1) and secure with
M6 x 12 x 1SS Flat Washers and M6 Nyloc
Nuts (Items 3, 4).
3.1
3.2
3.2
Choose which side for the Slimline II Tray
you'd like to install the Awning.
On the chosen side, place the Mounting
Brackets (Item 2) between two slats, starting
at either end of the side profile of the Rack.
Place the third Mounting Bracket in the
center. Make sure the two holes on the
bracket are facing upward. Using a white
marking pen, mark the three center holes
in each Mounting Bracket.
Remove the three Mounting Brackets.
With the help of a friend, lift the Awning up
and move towards the Basket while
lining-up the bolts in the Awning with the
holes in the Mounting Brackets. Fit Flat
Washers and Nyloc Nuts (Items 3,4 or 7, 8)
onto each bolt.
Fully tighten all fasteners and place Nut Caps
over nuts (Either Item 5 or 9).
6.5MM
Depending on the type of Awning Extrusion,
slide either three M6 x 16 Hex Bolt or three
M8 x 20 Hex Bolts (Items 1 or 6) into the top
slot and three into the bottom slot of the
extrusion.
4
3
2
1
1
4
3
10MM
13MM
RRAC029_REV_C01 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
5
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
6
Now's the time to visit your favorite Front Runner Dealer in person or Online.
COMPLETION
4
9
4.1
Congratulations! You did it. Take a step back and admire your work!
5Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Front Runner Accessoires automobiles
Front Runner
Front Runner Toyota LAND Cruiser 100 SLIMLINE II Manuel utilisateur
Front Runner
Front Runner SSDR012 Manuel utilisateur
Front Runner
Front Runner TRCA004 Manuel utilisateur
Front Runner
Front Runner RRAC210 Manuel utilisateur
Front Runner
Front Runner RRAC051 Manuel utilisateur
Front Runner
Front Runner RRAC105 Manuel utilisateur
Front Runner
Front Runner RRAC129 Manuel utilisateur
Front Runner
Front Runner RRAC203 Manuel utilisateur
Front Runner
Front Runner SSDS113 Manuel utilisateur
Front Runner
Front Runner LALD005 Manuel utilisateur
Front Runner
Front Runner Slimline II FATF005 Manuel utilisateur
Front Runner
Front Runner BGTH002 Manuel utilisateur
Front Runner
Front Runner RRAC242 Manuel utilisateur
Front Runner
Front Runner SLIMLINE II KRFE009T Manuel
Front Runner
Front Runner JCH004 Manuel utilisateur
Front Runner
Front Runner TRAC003 Manuel utilisateur
Front Runner
Front Runner KSVT001 Manuel utilisateur
Front Runner
Front Runner BPTH007 Manuel utilisateur
Front Runner
Front Runner SSDS105 Manuel utilisateur
Front Runner
Front Runner SHOWER ARM MKII Manuel utilisateur
