Front Runner LATF001 Manuel utilisateur
LATF001_REV_A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
front runner
LATF001
ENG
1
Thank you for purchasing Front Runner Toyota 4Runner (5th Gen) Ladder.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
TOYOTA 4RUNNER (5TH GEN)LADDER
LATF001_REV_A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
2
TOOLS NEEDED
FIGURE 1.1
GET ORGANIZED
1
IN THE BOX
1
19
3
4
5
6
2
10
5
11
12
13
1 1 X Top RH Ladder Side
2 20 X M6x12 Button Head Screw
3 2 X Bottom Ladder Side 1LH+1RH
4 1 X Press Plate
5 11 X M6x16 Button Head Screw
6 28 X M6 Nut Cap
7 28 X M6 Nyloc Nut
8 28 X M6 Flat Washer
9 1 X Bottom Bracket
10 1 X Bottom Rung
11 1 X Middle Rung
12 2 X Joiner Plate
13 1 X Upper Rung
14 1 X Top LH Ladder Side
IN THE BOX
15 1 X Ladder Top Step
16 2 X M8 Flat Washer
17 2 X M8 Nyloc Nut
18 2 X M8 Nut Cap
19 1 X Top Mounting Bracket
7
8
9
3
6
14
7 8
15
16
17 18
4mm
10mm
13mm
De-Natured
Alcohol
2
LATF001_REV_A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE2
2.1
2.2
2.3
Assemble Top LH Ladder Side (Item 14),
Ladder Top Step (Item 15), Upper Rung
(Item 13) and the Top RH Ladder Side (Item
1), using four M6x12 Button Head Screws,
four M6x16 Button Head Screws and eight
M6 Nyloc Nuts (Item 2,11, 8 & 7). Finish off
by placing eight M6 Nut Caps over the M6
Nyloc Nuts.
Assemble the Bottom LH and RH Ladder
Sides (Item 3), Ladder Rung (Item 10) and
Ladder Rung (Item 11) using eight M6x12
Button Head Screws, eight M6 Flat Washers
and M6 Nyloc Nuts (Item 2, 8 & 7). Finish off
by placing eight M6 Nut Caps (Item 6) over
the M6 Nyloc Nuts.
Assemble the Top Ladder assembly and
Bottom Ladder assembly using the two
Joiner Plates (Item 12), eight M6x12 Button
Head Screws, eight M6 Flat Washers and
eight M6 Nyloc Nuts (Item 2, 8 & 7). Finish
off by placing eight M6 Nut Caps (Item 6)
over the M6 Nyloc Nuts.
1
2
14
15
13
6 7 8
4mm
10mm
6 7 8
3
2
10
11
3
6 7 8 12
2
4mm
10mm
4mm
10mm
11
LATF001_REV _A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
4
FIT AND SECURE
2
2.4
2.5
2.6
Measure 100mm from the inside edge of the
spoiler trim, along the hatch edge and mark
with masking tape as shown.
Clean the surface where the Top Mount
Bracket (Item 19) wil be secured with
De-Natured Alcohol.
Remove the backing tape of the self-adhe-
sive tape on the bottom of the Top Mount
Bracket and hook the Top Mount Bracket
over the top hatch edge.
Position the Top Mount Bracket hook next to
the masking tape.
Press on the front hook, making sure the
hook is evenly pressed up against the hatch
top edge.
Remove the masking tape and firmly press
the Top Mount Bracket down to secure the
bracket to the hatch.
Open the rear hatch. Measure 220mm from
the outside hatch edge and mark it with
masking tape as shown.
De-Natured
Alcohol
100mm
220mm
LATF001_REV _A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
5
FIT AND SECURE
2
2.7
2.8
2.9
Clean the inside bottom edge lip using
De-Natured Alcohol. Remove the backing
tape from the self-adhesive tape on the
Press Plate (Item 4) and firmly secure the
Press Plate to the inside bottom edge lip as
shown.
Loosely secure three M6x16 Button Head
Screws to the Bottom Bracket (Item 9) and
fit the Bottom Bracket over the bottom hatch
lip and Press Plate. Hand tighten the M6x16
Button Head Screws to hold the Bottom
Bracket in place.
Carefully close the hatch.
Hook the ladder over the studs in the Top
Mount Bracket and lower the ladder. Loosely
secure the ladder to the Bottom Bracket
using four M6x16 Button Head Screws, four
M6 Flat Washers and four M6 Nyloc Nuts
(Item 5, 8 & 7).
Fully tighten the M6x16 Button Head Screws
on the Bottom Bracket.
Fully secure the ladder to the Top Mount
Bracket (Item 19) using two M8 Flat Washers
and two M8 Nyloc Nuts (Item 16 & 17). Finish
off by placing two M8 Nut Caps (Item 18)
over the M8 Nyloc Nuts.
The Ladder Bottom and Bottom Bracket
should be face to face.
Finish off by placing four M6 Nut Caps
(Item 6) over the M6 Nyloc Nuts.
TIP: Start with the forward LH and RH
fasteners, alternating between the
fasteners to pull the ladder down evenly.
10mm
13mm
4mm
De-Natured
Alcohol
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!
LATF001_REV _A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
6
FIT AND SECURE
2
2.10
Open the rear hatch.
Fully tighten the three M6x16 Button Head
Screws (Item 5).
Table des matières
Autres manuels Front Runner Accessoires automobiles
Front Runner
Front Runner KRJW021T Manuel utilisateur
Front Runner
Front Runner FAJL002 Manuel utilisateur
Front Runner
Front Runner FAMG001 Manuel utilisateur
Front Runner
Front Runner FAJK002 Mode d’emploi
Front Runner
Front Runner TRCA005 Manuel utilisateur
Front Runner
Front Runner SLIMLINE II KRFE009T Manuel
Front Runner
Front Runner LAMS001 Manuel utilisateur
Front Runner
Front Runner RRAC054 Manuel utilisateur
Front Runner
Front Runner LAVT003 Manuel utilisateur
Front Runner
Front Runner TRCA004 Manuel utilisateur
Front Runner
Front Runner SHOW013 Manuel utilisateur
Front Runner
Front Runner RRAC120 Manuel utilisateur
Front Runner
Front Runner SLIMLINE II Manuel utilisateur
Front Runner
Front Runner FAJL004 Manuel utilisateur
Front Runner
Front Runner Toyota LAND Cruiser 100 SLIMLINE II Manuel utilisateur
Front Runner
Front Runner SSDS110 Manuel utilisateur
Front Runner
Front Runner Slimline II KRKS007T Manuel utilisateur
Front Runner
Front Runner SLIMLINE II Manuel utilisateur
Front Runner
Front Runner RRAC203 Manuel utilisateur
Front Runner
Front Runner GBHO012 Manuel utilisateur
