FIC VT-501 Guide de référence

11

Installation Procedures

The VT-501 has several user-adjustable jumpers on the board that allow you to

configure your system to suit your requirements. This chapter contains

information on the various jumper settings on your mainboard.

To set up your computer, you should follow these installation steps:

■Step 1 -

Set system jumpers

■Step 2 -

Install DRAM and SDRAM modules

■Step 3 -

Install the CPU

■Step 4 -

Install expansion cards

■Step 5 -

Connect cables and power supply

■Step 6 -

Set up BIOS feature (Please read Chapter Three.)

Chapter 2

VT-501 Mainboard Manual

12

Mainboard Layout

Installation Procedures

13

1). Set System Jumpers

Jumpers

Jumpers are used to select the operation modes for your system. Some jumpers

on the board have three metal pins with each pin representing a different

function. To “set” a jumper, a black cap containing metal contacts is placed

over the jumper pin/s according to the required configuration. A jumper is said

to be “shorted” when the black cap has been placed on one or two of its pins.

The types of jumpers used in this manual are shown below:

NOTE : Users are not encouraged to change the jumper settings not listed in

this manual. Changing the jumper settings improperly may adversely affect

system performance.

VT-501 Mainboard Manual

14

Clear Password: CPW

This jumper allows you to set the password configuration to “Enabled” or

“Disabled”. You may need to enable this jumper if you forget your password.

Flash EPROM Type: EP1, EP2 and EP3

These three jumpers allows you to configure the mainboard when using the

MXIC 28F1000, Intel 28F001, SST 29EE010 (default), ATMEL 29C0101A,

MXIC 28F2000, SST 29EE0202 Flash EPROM chip.

Installation Procedures

15

2). Install System Memory

DRAM and SDRAM

The working space of the computer is the Random Access Memory (RAM).

The system cannot act upon data unless it is loaded into RAM. When more

memory is added, the working memory of the computer is larger, thereby

increasing total performance.

The VT-501’s RAM is comprised of two industry standard 72-pin Single In-

line Memory Modules (SIMMs) and one 168-pin Dual In-line Memory Module

(DIMM). The SIMM socket is able to support from 8 to 128MB FPM (Fast

Page Mode) and EDO (Extended Data Out) DRAM. Its DIMM socket is able

to support 64MB SRAM (Synchronous DRAM).

SDRAM is an advanced new memory technology that boosts overall system

performance with its ability to synchronize all operations with the processor

clock signal. This makes the implementation of control interfaces easier, and

speeds up column access time. SDRAM features an on-chip burst counter that

can be utilized to increment column addresses for very fast burst accesses,

which means that SDRAM allows new memory accesses to be initiated before

the preceding access has been finished.

Before making DRAM upgrades you should verify the type and speed of the

RAM currently installed from your dealer. Installing mixtures of RAM types

other than those described in this manual will have up unpredictable results.

VT-501 Mainboard Manual

16

DRAM and SDRAM Configuration

TOTAL

MEMORY SIMM

BANK0 (72-PIN X 2) DIMM

BANK1 (168-PIN X 1)

8MB 4MB & 4MB

8MB

16MB 8MB & 8MB

4MB & 4MB 8MB

24 MB 8MB & 8MB 8MB

32 MB 8MB & 8MB 16MB

16MB & 16MB

40MB 16MB & 16MB 8MB

48MB 16MB & 16MB 16MB

64MB 16MB & 16MB 32MB*

32MB & 32MB

72MB 32MB & 32MB 8MB

80MB 32MB & 32MB 16MB

96MB 32MB & 32MB 32MB*

128MB 32MB & 32MB 64MB*

Note : * A DIMM of this size was not available for testing when this book

was printed.

Installation Procedures

17

Install SIMMs

Complete the following procedures to install SIMMs:

CAUTION : Always turn the system power off before installing or removing

any device; and see “Handling Precautions” at the start of this manual.

1. Locate the SIMM slots on the mainboard. (See figure below.)

NOTE : BANK 0 and BANK 1 can use different type SIMMs - but you must

populate each memory bank with the same type of SIMM. The BIOS will

automatically configure the memory size.

2. Carefully fit a SIMM at a 45

degree angle into each empty

sockets to be populated. All the

SIMMs must face the same

direction.

3.

Swing each SIMM into its

upright, locked position.

When locking a SIMM

in place, push on each end of the SIMM -

do not push in the middle, as shown above.

Remove SIMMs

To remove the SIMMs, pull the retaining latch on both ends of the socket and

reverse the procedure above.

VT-501 Mainboard Manual

18

Install DIMM

Complete the following procedures to install DIMMs:

1. Locate the DIMM slot on the mainboard. (See figure below.)

2. Insert the DIMM straight down onto the DIMM slot with both hands

carefully until the clips on the ends of the slot close up to hold the DIMM

firmly.

Remove DIMM

Press the clips on the ends of the slot simultaneously. The DIMM will spring

out easily.

Installation Procedures

19

Cache Memory

The VT-501 comes with onboard 256KB/512KB synchronous 3V Pipeline

Burst SRAM.

Please note that for 256KB secondary cache, M2 and M3 should be mounted

with 32Kx32 Pipeline Burst SRAM. (Please refer to your dealer for the 512KB

cache upgrade and the appropriate SRAM type.)

VT-501 Mainboard Manual

20

256/512KB Cache SRAM

NOTE : Use the correct chips for the amount of cache memory you want to

add. Install both the correct Cache and Tag SRAM.

Autres manuels pour VT-501

1

Table des matières

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur