Endress+Hauser CM14-AAK Manuel utilisateur

Products Solutions Services

Operating Instructions

CM14

Transmitter, pH and ORP

BA01032C/09/EN/02.14

71257172

Valid as of FW version:

02.00.xx

AUTHORIZED DISTRIBUTOR:

InstrumentsAndControl.com

Houston, Texas USA

[email protected]

281-609-7170

AUTHORIZED DISTRIBUTOR:

InstrumentsAndControl.com

Houston, Texas USA

[email protected]

281-609-7170

CM14 Table of contents

Endress+Hauser 3

Table of contents

1 Safety instructions .............. 4

1.1 Workplace safety .................... 4

1.2 Requirements concerning the staff ...... 4

1.3 Operational safety ................... 4

1.4 Designated use ...................... 5

1.5 Technical improvement ............... 5

1.6 Return ............................. 5

1.7 Notes on safety conventions and

icons ............................... 5

2 Identification .................... 7

2.1 Device designation ................... 7

2.2 Scope of delivery ..................... 7

2.3 Certificates and approvals ............. 8

3 Installation ...................... 9

3.1 Incoming acceptance, transport,

storage ............................. 9

3.2 Installation ......................... 9

3.3 Dimensions ......................... 9

3.4 Installation procedure ............... 10

3.5 Post-installation check ............... 10

4 Wiring .......................... 11

4.1 Connecting the transmitter ........... 12

4.2 Post-connection check ............... 13

5 Operation ...................... 14

5.1 Display and device status indicator/

LED ............................... 14

5.2 Local operation at the device .......... 14

5.3 Icons .............................. 15

5.4 Operating functions ................. 16

5.5 Hold function ...................... 16

6 Commissioning ................ 17

6.1 Installation check and switching on the

device ............................. 17

6.2 Display settings (Display menu) ....... 17

6.3 Configuration of the device (Setup

menu) ............................ 17

6.4 Extended configuration (Extended

setup menu) ....................... 18

6.5 Device diagnostics (Diagnostics menu) .21

7 Calibration and adjustment .. 22

7.1 Definitions ......................... 22

7.2 pH sensors ......................... 22

7.3 ORP sensors ........................ 24

7.4 Device functions for calibration ....... 25

8 Maintenance .................. 25

9 Accessories .................... 26

9.1 Sensors ........................... 26

10 Troubleshooting ............... 27

10.1 Troubleshooting instructions ......... 27

10.2 Diagnostic messages ................ 27

10.3 Spare parts ........................ 32

10.4 Return ............................ 32

10.5 Disposal ........................... 33

11 Technical data ................. 33

Index ................................. 41

Safety instructions CM14

4 Endress+Hauser

1 Safety instructions

Reliable and safe operation of the transmitter is guaranteed only if the user reads these

Operating Instructions and complies with the safety instructions they contain.

1.1 Workplace safety

For work on and with the device:

‣Wear the required personal protective equipment according to federal/national

regulations.

1.2 Requirements concerning the staff

The personnel for installation, commissioning, diagnostics and maintenance must fulfill the

following requirements:

‣Trained, qualified specialists: must have a relevant qualification for this specific function

and task

‣Are authorized by the plant owner/operator

‣Are familiar with federal/national regulations

‣Before beginning work, the specialist staff must have read and understood the instructions

in the Operating Instructions and supplementary documentation as well as in the

certificates (depending on the application)

‣Following instructions and basic conditions

The operating personnel must fulfill the following requirements:

‣Being instructed and authorized according to the requirements of the task by the facility's

owner-operator

‣Following the instructions in these Operating Instructions

1.3 Operational safety

Risk of injury.

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for interference-free operation of the device.

Conversions to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers.

‣If, despite this, modifications are required, consult with Endress+Hauser.

Repair

To ensure continued operational safety and reliability,

‣Carry out repairs on the device only if they are expressly permitted.

‣Observe federal/national regulations pertaining to repair of an electrical device.

‣Use original spare parts and accessories from Endress+Hauser only.

CM14 Safety instructions

Endress+Hauser 5

Environmental requirements

If a plastic transmitter housing is permanently exposed to certain steam and air mixtures, this

can damage the housing.

‣If you are unsure, please contact your Endress+Hauser Sales Center for clarification.

‣If used in an approval-related area, observe the information on the nameplate.

1.4 Designated use

The transmitter evaluates measured values of an analytical sensor and displays them on its

multicolor display. Processes can be monitored and controlled using the transmitter outputs

and limit relays. The device is equipped with a wide range of software functions for this

purpose.

• The manufacturer accepts no liability for damages resulting from incorrect use or use other

than that designated. It is not permitted to convert or modify the device in any way.

• The device is designed for installation in a panel and must only be operated in an installed

state.

1.5 Technical improvement

The manufacturer reserves the right to modify technical data without prior notice. Please

contact your sales center for information on modifications or updates to the Operating

Instructions.

1.6 Return

For a return, e.g. in case of repair, the device must be sent in protective packaging. The

original packaging offers the best protection. Repairs must only be carried out by your

supplier's service organization.

When returning the device for repair, enclose a note with a description of the problem

and the application.

1.7 Notes on safety conventions and icons

1.7.1 Warnings

!DANGER

Causes (/consequences)

Consequences of non-compliance (if applicable)

‣Corrective action

‣This symbol alerts you to a dangerous situation. Failure to avoid the situation will result in

a fatal or serious injury.

!WARNING

Causes (/consequences)

Consequences of non-compliance (if applicable)

‣Corrective action

‣This symbol alerts you to a dangerous situation. Failure to avoid the situation can result in

a fatal or serious injury.

Safety instructions CM14

6 Endress+Hauser

!CAUTION

Causes (/consequences)

Consequences of non-compliance (if applicable)

‣Corrective action

‣This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or more serious injuries.

NOTICE

Causes (/consequences)

Consequences of non-compliance (if applicable)

‣Corrective action

‣This symbol alerts you to situations which may result in damage to property.

1.7.2 Document symbols

Permitted

Indicates procedures, processes or actions that are permitted.

Preferred

Indicates procedures, processes or actions that are preferred.

Forbidden

Indicates procedures, processes or actions that are forbidden.

Additional information, tips

Reference to documentation

Reference to a page in this manual

Reference to a graphic

CM14 Identification

Endress+Hauser 7

2 Identification

2.1 Device designation

2.1.1 Nameplate

Compare the nameplate with the following diagram:

-10°C (14°F) < Ta < 60°C (140°F)

â 1

Liquiline

A0015221

 1 Nameplate of the transmitter (example)

1 Device designation

2 Order code, serial number and ID number of the device

3 Power supply

4 Power consumption

5 Output values

6 Temperature range

2.2 Scope of delivery

The scope of delivery of the transmitter comprises:

• Transmitter for panel mounting

• Operating Instructions

• Fastening fixtures

Identification CM14

8 Endress+Hauser

2.3 Certificates and approvals

CE mark, Declaration of Conformity

The process display unit is designed to meet state-of-the-art safety requirements, has been

tested, and left the factory in a condition in which it is safe to operate. The device complies

with the applicable standards and regulations in accordance with EN 61 010-1 "Safety

requirements for electrical equipment for measurement, control and laboratory use".

The device described in these Operating Instructions therefore complies with the statutory

requirements of the EU Directives. The manufacturer confirms that the device has been

successfully tested by applying the CE mark.

An overview of all the certificates and approvals available is provided in the "Technical data"

section.

CM14 Installation

Endress+Hauser 9

3 Installation

3.1 Incoming acceptance, transport, storage

The permitted ambient and storage conditions must be observed. The precise specifications

can be found in Section "Technical data" (→  33).

3.1.1 Incoming acceptance

On receipt of the goods, check the following points:

• Are the packaging or contents damaged?

• Is anything missing from the delivery? Compare the scope of delivery with the information

you specified in the order.

3.1.2 Transportation and storage

Note the following points:

• Pack the device so that is protected against impact for storage and transportation. The

original packaging provides optimum protection.

• The permitted storage temperature range is –40 to +85 °C (–40 to +185 °F); it is possible to

store the device in the borderline temperature ranges for a limited period (maximum 48

hours).

3.2 Installation

NOTICE

Overheating due to heat accumulation in the device

‣To avoid heat accumulation, please always make sure the device is sufficiently cooled.

If the device is operated in the upper temperature limit range, this reduces the operating

life of the display.

The transmitter is designed to be used in a panel.

The orientation is determined by the readability of the display. Connections and outputs are

fitted on the rear of the device. The wires are connected by means of number-coded terminals.

Ambient temperature range:–10 to +60 °C (14 to 140 °F)

3.3 Dimensions

Observe the installation depth of 150 mm (5.91 ") for the device incl. terminals and fastening

clips.

More dimensions can be found in Section "Technical data" (→  33).

• Panel cutout: 92 mm x 45 mm (3.62 in x 1.77 in).

• Panel thickness: max. 26 mm (1 in).

• Max. viewing angle range: 45° to the left and right from the central display axis.

• If the devices are arranged horizontally beside one another in the X-direction, or arranged

vertically on top of one another in the Y-direction, the mechanical distance (specified by the

housing and front section) must be observed.

Installation CM14

10 Endress+Hauser

3.4 Installation procedure

The required panel cutout is 92 mm x 45 mm (3.62 in x 1.77 in).

A0015216

 2 Installation in the panel

1. Screw the threaded rods (item 2) into the positions provided on the mounting frame

(item 1). Four opposing screw positions (item 3/4) are available for this purpose.

2. Push the device with the sealing ring through the panel cutout from the front.

3. To secure the tube in the panel, hold the device in a horizontal position and push the

installation frame (item 1), with the threaded rods screwed in, over the tube until the

frame locks into position.

4. Tighten the threaded rods to fasten the device in place.

To disassemble the device, the mounting frame can be unlocked at the locking elements (item

5) and then removed.

3.5 Post-installation check

• Is the sealing ring undamaged?

• Is the mounting frame securely engaged on the housing of the device?

• Are the threaded rods tightened?

• Is the device positioned in the center of the panel cutout?

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Endress+Hauser Émetteur

Endress+Hauser

Endress+Hauser Omnigrad TMT146 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Prosonic Flow 93 Manuel utilisateur

Endress+Hauser

Endress+Hauser cerabar S PROFIBUS-PA Manuel utilisateur

Endress+Hauser

Endress+Hauser OTMT85 Manuel utilisateur

Endress+Hauser

Endress+Hauser Heat Caractéristiques techniques

Endress+Hauser

Endress+Hauser Proline 500 HART Caractéristiques techniques

Endress+Hauser

Endress+Hauser Proline Promass O 100HART Caractéristiques techniques

Endress+Hauser

Endress+Hauser iTEMP TMT112 Manuel utilisateur

Endress+Hauser

Endress+Hauser RMA42 Manuel utilisateur

Endress+Hauser

Endress+Hauser Flowmeter Proline 300 Caractéristiques techniques

Endress+Hauser

Endress+Hauser iTEMP TMT162 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M COM 223 F Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT84 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Liquisys M CUM223 Manuel utilisateur

Endress+Hauser

Endress+Hauser TMT122 Manuel utilisateur

Endress+Hauser

Endress+Hauser TMD1000 Manuel utilisateur

Endress+Hauser

Endress+Hauser HART Flowmeter Proline 400 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Liquisys M CLM223/253 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline 300 PROFIBUS PA Manuel utilisateur

Endress+Hauser

Endress+Hauser smartgrad TMD833 Manuel utilisateur

Endress+Hauser

Endress+Hauser PROFIBUS DP Proline 100 Caractéristiques techniques

Endress+Hauser

Endress+Hauser iTEMP TMT85 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M CLM 223 Manuel utilisateur

Endress+Hauser

Endress+Hauser Levelflex M FMP45 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur